Desa EFP33NRB Electrical Connections for Power Cord, Relocating Wall Switch Assembly

Page 10

INSTALLATION

Continued

3.Remove screws that attach fireplace floor as- sembly to fireplace. Open lower louver door. Carefully lift up fireplace floor assembly and remove from fireplace, taking care to pull flexible gas line through the access holes (see Figure 6). Note: Be careful of all wires on underside of log base.

CAUTION: Do not pick up fireplacefloorassemblybyburn- ers. This could damage burners. Only handle base by grates.

Flexible Gas Line

Screws

Fireplace Floor

Assembly

Figure 6 - Removing Fireplace Floor

Assembly

ELECTRICAL CONNECTIONS FOR POWER CORD

This fireplace operates on 120 VAC, 60 Hz power. An electrical power cord is supplied with this unit.

For Mantel Installation

1.Determine from which side of the fireplace the power cord will exit. Locate the 1.5" diameter hole near the center of floor support bracket on appropriate side of lower cavity (see Figure 7).

2.Locate power cord. Remove wire tie or tape holding plug end of power cord.

3.Power cord has 2 plastic hole bushings threaded onto it. Route cordʼs 3-prong plug through the 1.5" diameter hole in appropriate floor support bracket.

4.Push first plastic bushing completely through hole. Squeeze bushing as needed to do this.

5.Install the second plastic bushing into the hole in the floor support bracket by snapping into place.

6.Route the 3-prong plug through the 1.5" hole in fireplace outer casing.

7.Install the first plastic bushing into this hole by snapping into place.

8.After you have connected to gas supply and checked your gas connections (see pages 17 through 20), plug power cord into any conve- nient 3-prong grounded wall receptacle near fireplace.

For Recessed Installation

 

If an outlet is not installed in fireplace, install

model GA3555 - Outlet Kit with Cover. This

kit will supply a convenient 3-prong grounded

electrical outlet for power. Refer to installation

manual provided with this optional accessory for

instructions on wiring. Note: A qualified installer

must make all electrical connections.

Hole in Floor

Hole in Outer

Support Bracket

Casing

Bushings

Power

Cord

Figure 7 - Routing Power Cord

RELOCATING WALL SWITCH ASSEMBLY

Note: The decorative wall switch plate supplied is white. The wall switch plate may be painted to match your decor.

The push-button switch and decorative wall plate assembly supplied with your fireplace is pre-mounted at the factory in the lower cavity of the fireplace. You may relocate this wall switch assembly to a more convenient location such as the side of your mantel or directly onto the wall near the fireplace. To mount the wall switch assembly, you must first cut openings in the mantel or wall where the switch will be located.

10

www.desatech.com

111245-01B

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Shown with optional Hearth base accessory CGEFP33PRB, CGEFP33NRB EFP33PRB, EFP33NRBTable of Contents Safety Information Fireplace Floor Assembly Product IdentificationLocal Codes Product FeaturesUnpacking Providing Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation AIR Ventilation Air From Inside BuildingCheck GAS Type InstallationVentilation Air From Outdoors Removing Fireplace Screen and Floor Assembly Installation ClearancesInstallation Sequence Electrical HookupRelocating Wall Switch Assembly Electrical Connections for Power CordFor Mantel Installation For Recessed Installation For Recessed FireplaceMounting Wall Switch Assembly to Side of Mantel Cutting LinesInstalling Variable Speed Blower Accessory Mounting Blower to FireboxLocation of Wiring Diagram Decal 3 from Blower Installing Thermostatic Blower Accessory Installing Switch and Cover Assembly and Speed ControlInstalling Bushings Installation Items Needed Installing GAS Piping to Fireplace LocationOperating the Blower Natural Connecting Fireplace to GAS SupplyPropane/LP Test Pressures In Excess Of 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Conventional Fireplace Installation Pressure Testing Fireplace GAS ConnectionsBUILT-IN Fireplace Installation Nailing FlangesRough Opening for Installing Wall Installing Hood Top Brass Trim Side Brass Trim Adjusting Set ScrewsInstalling Logs Installing Back Log #1 Cgefp Logs ShownFor Your Safety Read Before Lighting Installing Battery Into RemoteInstalling Screen Operating FireplaceNormal Lighting Instructions Using Supplied Wall Switch AssemblyControl Shutting Off Heater Wireless Remote Control Manual Lighting Instructions for Electrical Power OutageTo Turn OFF GAS To Appliance Pilot Flame Pattern Inspecting BurnersOptional Blower Operation Main BurnerPilot AIR Inlet Hole Cleaning MaintenanceBurner Injector Holder LogsTroubleshooting Observed Problem Possible Cause RemedySee Cleaning and Mainte Gas leak. See Warning Statement aboveTechnical Service SpecificationsService Hints When Gas Pressure Is Too LowIllustrated Parts Breakdown Parts List Remote Control LOG Base AssemblyIllustrated Parts Breakdown KEY Part Number EFP33PRB EFP33NRB Description QTY Firebox Models CGEFP33PRB, CGEFP33NRB, EFP33PRB and EFP33NRB KEY Part Number Description QTY Replacement Parts AccessoriesCorner Hearth Base for USE with Corner Mantel Corner Mantel Accessory with Fireplace Perimeter TrimHearth Base for USE with Cabinet Mantel Wiring Diagram Templates This page Intentionally Left Blank Parts Central 111245-01B 111245-01B Not a UPC

EFP33NRB, CGEFP33PRB, CGEFP33NRB, EFP33PRB, EFP33NRB specifications

Desa offers a range of premium electric fireplaces with models such as EFP33NRB, CGEFP33PRB, CGEFP33NRB, EFP33PRB, and EFP33NRB, each designed to blend aesthetics with advanced heating technology. These electric fireplaces are renowned for their ability to create a warm ambiance without the hassle of traditional wood or gas fireplaces.

The EFP33NRB model, a part of Desa's electric fireplace collection, features a sleek design that fits seamlessly into various interior styles. With its realistic flame effect and adjustable brightness settings, users can customize their experience, enhancing any room while maintaining a cozy atmosphere. This model also incorporates energy-efficient LED technology, ensuring minimal power consumption without compromising on the visual appeal and comfort.

Similarly, the CGEFP33PRB and CGEFP33NRB are designed for those who appreciate the combination of style and functionality. These models offer a robust heating output, capable of warming larger spaces efficiently. The innovative heat management system also ensures even heat distribution, making these units suitable for year-round use. Additionally, remote control capabilities allow for effortless adjustment, enhancing user convenience.

The EFP33PRB features a modern framework that showcases the flames within a stylish casing. Its user-friendly interface includes touch controls and an easy-to-read display, allowing users to change settings with ease. The fireplace boasts a range of flame colors, allowing for personalization to match any decor or mood.

Across all these models, safety remains a top priority with built-in overheat protection and a tip-over switch, providing peace of mind during operation. Furthermore, the fireplaces operate quietly, ensuring an undisturbed environment while creating a warm, inviting space.

In conclusion, the Desa EFP33NRB, CGEFP33PRB, CGEFP33NRB, EFP33PRB, and EFP33NRB models represent the pinnacle of electric fireplace technology. With their modern designs, efficiency, and flexibility, they offer a perfect solution for anyone looking to enhance their living spaces with warmth and style. Whether for a contemporary home or a cozy cabin, these fireplaces promise to deliver both comfort and elegance.
Top Page Image Contents