Desa CD36TN-M installation manual Continued, Horizontal Vent Installations

Page 14

Venting Installation instructions

Continued

HORIZONTAL VENT INSTALLATIONS

USING MULTIPLE 90° ELBOWS

The following configurations show the minimum vertical rise requirements for a horizontal system using two 90° elbows.

90° Elbow

Venting with Two 90° Elbows

	Horizontal (H)+
Vertical (V)	Horizontal (H2)
7' Min.	10' Max
8' Min.	12' Max
9' Min.	14' Max
10' Min.	16' Max
11' Min.	18' Max
13' Min.	20' Max

Figure 17 - Horizontal Termination Configuration For Venting Using Two 90° Elbows

Venting with Two 90° Elbows
		Horizontal (H)+
Vertical (V)	Horizontal (H)	Horizontal (H2)
5' Min.	2' Max.	6' Max
6' Min.	3' Max.	8' Max
7' Min.	4' Max.	10' Max	90°
8' Min.	5' Max.	12' Max	Elbow
12' Min.	8' Max.	20' Max
20' Min.	8' Max.	20' Max	90°
			90°
			Elbow
		H
		O
		T
			90°
			Elbow

Figure 18 - Horizontal Termination Configuration for Venting Using Three 90° Elbows

www.desatech.com

118531-01A

Image 14

Contents WHAT TO DO IF YOU SMELL GAS Table of Contents Safety Information Continued Safety informationProduct Identification Local Codes Product FeaturesPre-Installation Preparation Location and space requirementsPackaging and Removal Figure 3 - Fireplace Bottom DimensionsContinued ClearancesContinued InstallationFigure 6 - Unit Dimensions Figure 5 - Framing Clearances for CornerContinued MANTEL CLEARANCESInside Corner D E B LFigure 9 - Minimum Clearances for Termination Cap Outside CornerVenting Installation Instructions Continued Venting Installation instructionsINSTALLATION PLANNING Figure 10 - Vent Pipe ConnectionsInner Wall Firestop Figure 12 - Installing Siding StandoffFigure 13 - Installing Outer Wall Firestop Standoff Vent Cap Apply Mastic to All Four SidesConfiguration with Vertical Rise and One 90 Elbow Configuration For Corner InstallationUsing One 90 Elbow Clearance at Ground Floor InstallationHORIZONTAL VENT INSTALLATIONS ContinuedFigure 20 - Installing Firestop Installation for vertical terminationFlat Ceiling Installation ContinuedFigure 21 - Installing Thimble with Firestop Thimble InstallationVertical Termination Configurations for Top Vent ContinuedContinued parts list for venting kits and componentsConfiguration Using Two 90 Elbows Figure 23 - Vertical VentingNumber ContinuedELECTRICAL SUPPLY CONNECTION DescriptionFigure 28 - Attaching Speed Control to Installing optional blower accessoriesFigure 27 - Blower Model BK Firebox Millivolt ModelsFigure 30 - Blower Model BKT Model BKT InstallationContinued Figure 32 - Millivolt Ignition Wiring Diagram Wiring DiagramsFigure 31 - Blower Wiring Diagram for ContinuedInstalling Remote Receiver Installing optional wall Mount Switch - gwmS2Figure 33 - Connecting Wall Switch to Figure 34 - Attaching Alkaline Battery toContinued Installing Gas Piping to Fireplace LocationInstallation Items Needed Check Gas TypeFigure 39 - Connecting Flexible Gas Line CONNECTING FIREPLACE TO GAS SUPPLYInstallation Items Needed Pressure Testing Gas Supply Piping SystemFigure 42 - Checking Gas Joints for Removing/Replacing Glass DoorFigure 40 - Equipment Shutoff Valve Natural Gas FireplaceContinued Removing Lower Louver Access PanelFigure 43 - Removing Lower Louver Access Panel Removing Top Louver Trim PanelContinued Installing LOGS, lava rock and glowing embersFigure 46 - Installing Logs Figure 45 - Removing/Replacing Glass Doorlighting instructions for your safety Read before lightingOperating Fireplace TO TURN OFF GAS TO APPLIANCEContinued MANUAL LIGHTING PROCEDUREFigure 49 - Setting the Selector Switch optional Hand-Held REMOTE OPERATIONAuto Shutoff Feature operating optional blower accessorySafety Features Remote Control Unit HRC200Figure 52 - Pilot Assembly Millivolt pilot assemblysee Troubleshooting, page see Troubleshooting, pageContinued Figure 54 - Removing Logs and Burner AssemblyFigure 56 - Adjusting Air Shutter Pilot Orifice ConversionGas Control Conversion Cleaning and MaintenanceConversion Instructions GLASS DOORpilot and burners CAUTION: Do not vacuum if pieces are hotContinued logsPOSSIBLE CAUSE TroubleshootingOBSERVED PROBLEM REMEDYContinued TROUBLESHOOTINGOBSERVED PROBLEM POSSIBLE CAUSEWARNING If you smell gas Shut off gas supply Parts Not Under Warranty OBSERVED PROBLEMParts Under Warranty ContinuedMANUAL BLOWER KIT - BK WALL MOUNTED ON/OFF SWITCH GWMS2 Not ShownWhen Gas Pressure Is Too Low THERMOSTATICALLY - CONTROLLED BLOWER KIT - BKTFireplace Assembly for Model CD36TN-M Illustrated Parts BreakdownPARTS LIST FIREPLACE ASSEMBLY FOR MODEL CD36TN-MBURNER ASSEMBLY FOR MODEL CD36TN-M Illustrated parts breakdownBURNER ASSEMBLY FOR MODEL CD36TN-M 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16LIMITED WARRANTY DIRECT-VENTFIREPLACE Warranty InformationKEEP THIS WARRANTY