Desa CD36TN-M Removing/Replacing Glass Door, Equipment Shutoff Valve, Checking Gas Joints for

Page 25
Figure 40 - Equipment Shutoff Valve

Fireplace

Installation

Continued

4.

Check all joints of gas supply piping system.

 

Apply noncorrosive leak detection fluid to all

 

joints. Bubbles forming show a leak. Correct

 

all leaks at once.

5.

Reconnect fireplace and equipment shutoff

 

valve to gas supply. Check reconnected fittings

Equipment

Shutoff Valve

Gas

Meter

Gas Valve

for leaks.

Test Pressures Equal To or Less Than

1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 40).

2. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas fireplace or opening main gas valve located on or near gas meter for natural gas fireplace or using compressed air.

3. Check all joints from propane/LP supply tank or gas meter to equipment shutoff valve (see Figure 41, for propane/LP or Figure 42, for natural gas). Apply noncorrosive leak detec- tion fluid to all joints. Bubbles forming show a leak. Correct all leaks at once.

Equipment

Open

Shutoff Valve

 

Closed

Figure 40 - Equipment Shutoff Valve

Figure 42 - Checking Gas Joints for

Natural Gas Fireplace

Pressure Testing Fireplace Gas

Connections

1. Open equipment shutoff valve (see Figure 40).

2. Open propane/LP supply tank valve for propane/LP fireplace or main gas valve located on or near gas meter for natural gas fireplace.

3. Make sure control knob of fireplace is in the OFF position.

4. Check all joints from equipment shutoff valve to gas valve (see Figure 41 for propane/LP or Figure 42 for natural gas). Apply noncorrosive leak detection fluid to all joints. Bubbles form- ing show a leak. Correct all leaks at once.

5. Light fireplace (see Operating Fireplace, page

28). Check all other internal joints for leaks.

6. Turn off fireplace (see To Turn Off Gas to Ap- pliance, page 28).

Removing/Replacing Glass

Door

Propane/LP Supply Tank

Equipment Shutoff Valve

Gas Valve

Figure 42 - Checking Gas Joints for CAUTION: Do not operate this fireplace with a broken glass door panel or without the glass door panel securely in place. For replacement part informa- tion see Replacement Parts, page 38.

Natural Gas Fireplace CAUTION: Wear gloves and safety glasses while handling

Figure 41 - Checking Gas Joints for

Propane/LP Gas Fireplace

or removing broken glass. Do not remove if glass is hot. Keep children and pets away from glass.

118531-01A

www.desatech.com

25

Image 25
Contents WHAT TO DO IF YOU SMELL GAS Table of Contents Safety Information Product Identification Safety informationContinued Pre-Installation Preparation Product FeaturesLocal Codes Location and space requirementsContinued Figure 3 - Fireplace Bottom DimensionsPackaging and Removal ClearancesFigure 6 - Unit Dimensions InstallationContinued Figure 5 - Framing Clearances for CornerMANTEL CLEARANCES ContinuedFigure 9 - Minimum Clearances for Termination Cap D E B LInside Corner Outside CornerVenting Installation Instructions INSTALLATION PLANNING Venting Installation instructionsContinued Figure 10 - Vent Pipe ConnectionsFigure 13 - Installing Outer Wall Firestop Figure 12 - Installing Siding StandoffInner Wall Firestop Standoff Vent Cap Apply Mastic to All Four SidesUsing One 90 Elbow Configuration For Corner InstallationConfiguration with Vertical Rise and One 90 Elbow Clearance at Ground Floor InstallationContinued HORIZONTAL VENT INSTALLATIONSFlat Ceiling Installation Installation for vertical terminationFigure 20 - Installing Firestop ContinuedVertical Termination Configurations for Top Vent Thimble InstallationFigure 21 - Installing Thimble with Firestop ContinuedConfiguration Using Two 90 Elbows parts list for venting kits and componentsContinued Figure 23 - Vertical VentingELECTRICAL SUPPLY CONNECTION ContinuedNumber DescriptionFigure 27 - Blower Model BK Installing optional blower accessoriesFigure 28 - Attaching Speed Control to Firebox Millivolt ModelsContinued Model BKT InstallationFigure 30 - Blower Model BKT Figure 31 - Blower Wiring Diagram for Wiring DiagramsFigure 32 - Millivolt Ignition Wiring Diagram ContinuedFigure 33 - Connecting Wall Switch to Installing optional wall Mount Switch - gwmS2Installing Remote Receiver Figure 34 - Attaching Alkaline Battery toInstallation Items Needed Installing Gas Piping to Fireplace LocationContinued Check Gas TypeInstallation Items Needed CONNECTING FIREPLACE TO GAS SUPPLYFigure 39 - Connecting Flexible Gas Line Pressure Testing Gas Supply Piping SystemFigure 40 - Equipment Shutoff Valve Removing/Replacing Glass DoorFigure 42 - Checking Gas Joints for Natural Gas FireplaceFigure 43 - Removing Lower Louver Access Panel Removing Lower Louver Access PanelContinued Removing Top Louver Trim PanelFigure 46 - Installing Logs Installing LOGS, lava rock and glowing embersContinued Figure 45 - Removing/Replacing Glass DoorOperating Fireplace for your safety Read before lightinglighting instructions TO TURN OFF GAS TO APPLIANCEFigure 49 - Setting the Selector Switch MANUAL LIGHTING PROCEDUREContinued optional Hand-Held REMOTE OPERATIONSafety Features operating optional blower accessoryAuto Shutoff Feature Remote Control Unit HRC200see Troubleshooting, page pilot assemblyFigure 52 - Pilot Assembly Millivolt see Troubleshooting, pageFigure 56 - Adjusting Air Shutter Figure 54 - Removing Logs and Burner AssemblyContinued Pilot Orifice ConversionConversion Instructions Cleaning and MaintenanceGas Control Conversion GLASS DOORContinued CAUTION: Do not vacuum if pieces are hotpilot and burners logsOBSERVED PROBLEM TroubleshootingPOSSIBLE CAUSE REMEDYOBSERVED PROBLEM TROUBLESHOOTINGContinued POSSIBLE CAUSEWARNING If you smell gas Shut off gas supply Parts Under Warranty OBSERVED PROBLEMParts Not Under Warranty ContinuedWhen Gas Pressure Is Too Low WALL MOUNTED ON/OFF SWITCH GWMS2 Not ShownMANUAL BLOWER KIT - BK THERMOSTATICALLY - CONTROLLED BLOWER KIT - BKTIllustrated Parts Breakdown Fireplace Assembly for Model CD36TN-MFIREPLACE ASSEMBLY FOR MODEL CD36TN-M PARTS LISTIllustrated parts breakdown BURNER ASSEMBLY FOR MODEL CD36TN-M1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 BURNER ASSEMBLY FOR MODEL CD36TN-MKEEP THIS WARRANTY Warranty InformationLIMITED WARRANTY DIRECT-VENTFIREPLACE