Desa CD36TN-M Continued, Installing optional wall Mount Switch - gwmS2, Connecting Wall Switch to

Page 22
Installing optional wall Mount Switch - gwmS2

Fireplace

Installation

Continued

Installing optional wall Mount Switch - gwmS2

1.Connect one terminal of 25 ft. wire for the wall switch to the TPTH terminal on the valve. Con- nect remaining wire terminal to the TH terminal on the valve. Make sure that the wire terminals are in the positions on the unit as pictured in Figure 33. If wires are not connected as shown the switch will not work.

2.Route the 25 ft. wire through openings pro- vided on the sides of the burner system to a convenient location to mount your switch.

3.Connect one bare wire end to each of the terminals of the GWMS2 wall switch.

4.Install the wall switch and cover in the wall. IMPORTANT: Do not use any other wire than that provided with the GWMS2 wall switch kit. Do not exceed 15 ft. of distance from the valve connection. Using wire of higher gage or turns or exceeding the minimum distance will increase resistance at the control valve causing unreliable performance of the fireplace controls.

To Wall Switch

Accessory

Figure 33 - Connecting Wall Switch to

Control Valve

Installing Optional Wireless hand-held REMOTE CONTROL for millivolt Ignition - HRC100 and HRC200 Series

NOTICE: Use only alkaline bat- teries (not included).

Installing Remote Receiver

1. Open bottom louver and locate the switch bracket on the right

2. Locate the battery clip mounted on the back of the receiver. Slide a 9-volt alkaline battery (not included) through the clip

3. Attach the terminal wires to the battery (see Figure 34).

4. Connect wires from receiver to TH and TPTH to control valve (see Figure 33).

5.Locate the two plastic mounting clips provided with the kit.

6.Use the clips to mount the receiver on remote mounting bracket as shown in Figure 35.

Receiver

9-Volt Alkaline Battery

Terminal

Wires

Battery Clip

Figure 34 - Attaching Alkaline Battery to

Receiver

Plastic Mounting Clips

REMOTE ON OFF

Towards Front

Figure 33 - Connecting Wall Switch to Remote Receiver

Figure 35 - Mounting Remote Receiver to

Bracket

Installing 9-Volt Alkaline Battery in Hand-
Held Remote Control Unit

1. Remove battery cover on back of remote control unit.

2. Attach terminal wires to a 9-volt alkaline battery (not included). Place battery into the battery housing.

3. Replace battery cover onto remote control unit.

Battery Cover Remote Control Unit

Terminal

Wires

9-Volt

Battery

Housing

Battery

 

Figure 36 - Installing Battery in Hand-

Held Remote Control Unit

22

www.desatech.com

118531-01A

Page 21 Page 23
Image 22
Page 21 Page 23
Contents WHAT TO DO IF YOU SMELL GAS Table of Contents Safety Information Product Identification Safety informationContinued Local Codes Product FeaturesPre-Installation Preparation Location and space requirementsPackaging and Removal Figure 3 - Fireplace Bottom DimensionsContinued ClearancesContinued InstallationFigure 6 - Unit Dimensions Figure 5 - Framing Clearances for CornerContinued MANTEL CLEARANCESInside Corner D E B LFigure 9 - Minimum Clearances for Termination Cap Outside CornerVenting Installation Instructions Continued Venting Installation instructionsINSTALLATION PLANNING Figure 10 - Vent Pipe ConnectionsInner Wall Firestop Figure 12 - Installing Siding StandoffFigure 13 - Installing Outer Wall Firestop Standoff Vent Cap Apply Mastic to All Four SidesConfiguration with Vertical Rise and One 90 Elbow Configuration For Corner InstallationUsing One 90 Elbow Clearance at Ground Floor InstallationHORIZONTAL VENT INSTALLATIONS ContinuedFigure 20 - Installing Firestop Installation for vertical terminationFlat Ceiling Installation ContinuedFigure 21 - Installing Thimble with Firestop Thimble InstallationVertical Termination Configurations for Top Vent ContinuedContinued parts list for venting kits and componentsConfiguration Using Two 90 Elbows Figure 23 - Vertical VentingNumber ContinuedELECTRICAL SUPPLY CONNECTION DescriptionFigure 28 - Attaching Speed Control to Installing optional blower accessoriesFigure 27 - Blower Model BK Firebox Millivolt ModelsContinued Model BKT InstallationFigure 30 - Blower Model BKT Figure 32 - Millivolt Ignition Wiring Diagram Wiring DiagramsFigure 31 - Blower Wiring Diagram for ContinuedInstalling Remote Receiver Installing optional wall Mount Switch - gwmS2Figure 33 - Connecting Wall Switch to Figure 34 - Attaching Alkaline Battery toContinued Installing Gas Piping to Fireplace LocationInstallation Items Needed Check Gas TypeFigure 39 - Connecting Flexible Gas Line CONNECTING FIREPLACE TO GAS SUPPLYInstallation Items Needed Pressure Testing Gas Supply Piping SystemFigure 42 - Checking Gas Joints for Removing/Replacing Glass DoorFigure 40 - Equipment Shutoff Valve Natural Gas FireplaceContinued Removing Lower Louver Access PanelFigure 43 - Removing Lower Louver Access Panel Removing Top Louver Trim PanelContinued Installing LOGS, lava rock and glowing embersFigure 46 - Installing Logs Figure 45 - Removing/Replacing Glass Doorlighting instructions for your safety Read before lightingOperating Fireplace TO TURN OFF GAS TO APPLIANCEContinued MANUAL LIGHTING PROCEDUREFigure 49 - Setting the Selector Switch optional Hand-Held REMOTE OPERATIONAuto Shutoff Feature operating optional blower accessorySafety Features Remote Control Unit HRC200Figure 52 - Pilot Assembly Millivolt pilot assemblysee Troubleshooting, page see Troubleshooting, pageContinued Figure 54 - Removing Logs and Burner AssemblyFigure 56 - Adjusting Air Shutter Pilot Orifice ConversionGas Control Conversion Cleaning and MaintenanceConversion Instructions GLASS DOORpilot and burners CAUTION: Do not vacuum if pieces are hotContinued logsPOSSIBLE CAUSE TroubleshootingOBSERVED PROBLEM REMEDYContinued TROUBLESHOOTINGOBSERVED PROBLEM POSSIBLE CAUSEWARNING If you smell gas Shut off gas supply Parts Not Under Warranty OBSERVED PROBLEMParts Under Warranty ContinuedMANUAL BLOWER KIT - BK WALL MOUNTED ON/OFF SWITCH GWMS2 Not ShownWhen Gas Pressure Is Too Low THERMOSTATICALLY - CONTROLLED BLOWER KIT - BKTFireplace Assembly for Model CD36TN-M Illustrated Parts BreakdownPARTS LIST FIREPLACE ASSEMBLY FOR MODEL CD36TN-MBURNER ASSEMBLY FOR MODEL CD36TN-M Illustrated parts breakdownBURNER ASSEMBLY FOR MODEL CD36TN-M 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16KEEP THIS WARRANTY Warranty InformationLIMITED WARRANTY DIRECT-VENTFIREPLACE
Top Page Image Contents