Vermont Casting 3032, 3033 Complete the Installation, Vermont Castings UVS27 Vent-FreeGas Heater

Page 15
Complete the Installation

Vermont Castings UVS27 Vent-Free Gas Heater

Complete the Installation

1.Install the screen frame by sliding the hooks over the top front edge of the firebox and resting the bottom on the support brackets. If the catalyst has been installed, place the glass front on the stove by resting the bottom edge of the frame on support brackets below the front opening of the firebox. Rotate the top edge of the assembly toward the firebox, and center it. Rotate the right and left cams towards the back of the firebox to secure glass frame in place.

2.Grasp the front plate by the window bars and lift into position engaging the two steel tabs behind the adjacent bosses in the side plates. (Fig. 25) then seat the front against the sides so the tabs at the bottom lip engage with the notches in the stove legs.

Engage steel tabs behind the cast iron bosses

Control Door

Bottom Tabs engage notch in the leg.

ST112

Fig. 25 Install the Front Plate. Your Front may look different from that shown.

On the Pinnacle, the front tabs will engage behind the notched cutouts in the base of either side plate. (Fig. 26)

When properly installed, the bottom of the front plate cannot be pulled away form the sides without lifting it.

NOTE: Be sure that the control door can swing out. It should close against the steel tab stop.

If installing the optional warming shelf, you may find it easiest to attach it to the top plate before placing the top in position on the stove. Follow the instructions supplied with the kit.

 

Bottom Tabs engage notch

ST113

in the base.

Fig. 26 Engage the Hearthmount Front with the notch in the bse of each side plate.

3.Tilt the top plate to engage its rear rib in front of the back panel, then carefully lower it onto the sides. (Fig. 27) The upper edge of the side plates should seat into the channel in the underside of the top.

4.Lay the screen and top grille in place.

This completes assembly of the Stardance Freestand- ing and Pinnacle Hearthmount shells.

Grille

Screen

Manual background Top Plate

Levelling

Screws

ST114

Fig. 27 Install the Top Plate and Grille.

20005004

15

Image 15
Contents INSTALLER / CONSUMER SAFETY INFORMATION Homeowner’s InstallationWHATTO DO IF YOU SMELL GAS Do not try to light any appli- anceTable Of Contents Vermont Castings UVS27 Vent-FreeGas Heater20005004 Installation & Operating Instructions Vermont Castings UVS27 Vent-FreeGas Heater20005004 Freestanding Stove Shell DimensionsVermont Castings UVS27 Vent-FreeGas Heater 20005004Vermont Castings UVS27 Vent-FreeGas Heater Clearance RequirementsMinimum Clearances to Combustible Materials Hearth RequirementsANSI Z21.11.2a-2001 Unvented Heaters Gas SpecificationsGas Inlet and Manifold Pressures UVS27R & UVS27M Vent-Free Certified toProvide For Adequate Ventilation Vent Free FeaturesFresh Air Requirements for Combustion and Ventilation20005004 W A R N I N GVermont Castings UVS27 Vent-FreeGas Heater W A R N I N GVermont Castings UVS27 Vent-FreeGas Heater Assembly ProceduresShell / Firebox Assembly Unpack the FireboxInstall Optional Fan Kit Vermont Castings UVS27 Vent-FreeGas Heater20005004 Install ON/OFF Switch Vermont Castings UVS27 Vent-FreeGas Heater20005004 20005004 Glass & Catalyst InstallationThermostat Connection Optional Vermont Castings UVS27 Vent-FreeGas HeaterConnect the Gas Supply Line Vermont Castings UVS27 Vent-FreeGas Heater20005004 Install Log Set Vermont Castings UVS27 Vent-FreeGas Heater20005004 Complete the Installation Vermont Castings UVS27 Vent-FreeGas Heater20005004 Your First Fire Flame & Temperature AdjustmentFlame Characteristics OperationTo Turn Off Gas To Heater FOR YOUR SAFETY READ BEFORE LIGHTINGLighting and Operating Instructions Lighting InstructionsVermont Castings UVS27 Vent-FreeGas Heater TroubleshootingCONDITION POSSIBLE CAUSEPOSSIBLE CAUSE Troubleshooting cont’dVermont Castings UVS27 Vent-FreeGas Heater CONDITIONGlass Replacement MaintenanceFirebox Cleaning and Inspection Cleaning ProcedureReplace The Combustor Module Clean the Combustor ModuleCatalytic Combustor Remove the Combustor Module20005004 ModelsUVS27R, UVS27M Vent Free Gas Heaters Vermont Castings UVS27 Vent-FreeGas Heater20005004 UVS27R, UVS27M Vent Free Gas HeatersModels 3030, 3031, 3032, 3033 continued Vermont Castings UVS27 Vent-FreeGas HeaterShell Enamel Part Numbers - Hearthmount UVS27R, UVS27M Vent Free Gas HeatersVermont Castings UVS27 Vent-FreeGas Heater Models 3030, 3031, 3032, 3033 continuedGlass / Catalyst Kit UVGODCFK Optional Accessories AvailableRemote Controls Fan KitsVermont Castings UVS27 Vent-FreeGas Heater LIMITED LIFETIME WARRANTYPRODUCT COVERED BY THIS WARRANTY IF WARRANTY SERVICE IS NEEDED…