Drolet DG05437/DG05447 manual Straight Out Installation, Corner Installation

Page 17
1) STRAIGHT OUT INSTALLATION

ULTRA FLAME DV “0” Clearance Fireplace

Once the position of the fireplace and the termination cap are fixed, you should select the venting kit appropriate for your needs. First floor installations require either a STRAIGHT OUT kit or a CORNER kit while basement installations must be done with a BASEMENT kit. Please note that the BASEMENT kit can also be used on first (or higher) floors and it is possible to use up to 25' of pipe with a distant installation.

1) STRAIGHT OUT INSTALLATION

Make a 10-1/2" x 10-1/2" opening in the wall, 29-1/2" inches above the base of the fireplace.

Cut the radiation shield to length if necessary and install as shown. Secure with four #10 1” wood screws.

Install the vent pipe starting from the fireplace and working your way out.

NOTE: All joints must be sealed with RTV silicone, 315°C. (600°F) temperature resistance.

Attach the 4" flexible pipe on the fireplace with a locking band and cut to leave a 2- 1/2" projection over the exterior wall.

Slip on the 45°x8" elbow facing toward your wall hole. Seal it with silicone and secure with screws.

Add a spring spacer. The spring spacer must be located opposite the outside pipe joints to prevent puncturing of the inside pipe when the two sections of the outside pipe are screwed together.

Cut the 8" diameter pipe to be flush with outside face of the exterior wall and attach it to the 45° elbow through the radiation shield.

Secure the 8” elbow with screws and seal the pipe joints with silicone.

Cover the 8"diameter pipe with the insulation blanket and seal joint with aluminum tape.

Installation inside the house is now complete. The next step is to install the vent termination cap according to the instructions in the next section.

2) CORNER INSTALLATION

Make a 10-1/2" x 10-1/2" opening in the wall, 39-1/4" inches above the base of the fireplace.

Cut the radiation shield to length if necessary and install as shown. Secure with four #10 1” wood screws.

Install the vent pipe starting from the fireplace and working your way out.

NOTE: All joints must be sealed with RTV silicone, 315°C. (600°F) temperature resistance.

Attach the 4" flexible pipe on the fireplace with a locking band and seal with silicone cut to leave a 2-1/2" projection over the exterior wall.

Slip on the 45° x 8" elbow facing upward. Seal it with silicone and secure with screws.

17

Image 17
Contents FOR YOUR SAFETY INSTALLATION AND OPERATING INSTRUCTIONSFOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS DIRECT VENT 0 CLEARANCE GAS FIREPLACELIGHTING PROCEDURE SPECIFICATIONSMAINTENANCE INSTRUCTIONS GLASS MAINTENANCEKEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE GENERAL INFORMATIONDO NOT MODIFY THIS APPLIANCE SPECIFICATIONS OPERATION LIGHTING PROCEDUREBEFORE LIGHTING THE FIRST FIREBLOWER WALL THERMOSTATSHUTDOWN GLASS MAINTENANCE MAINTENANCE INSTRUCTIONSNever clean this glass with abrasive cleaners Use only a cleaner recommended by your dealerBURST DISC REPLACEMENT FRONT VIEW TOP, FRONT AND SIDE VIEWSTOP VIEW SIDE VIEWPOSITIONING THE FIREPLACE INSTALLATIONSAFETY NOTICE VENT TERMINAL LOCATION MINIMUM CLEARANCE TO COMBUSTIBLES INSTALLATION OF THE UNIT WARNING DO NOT USE OPEN FLAME TO CHECK LEAKS STRAIGH OUT VENTING KITSCORNER BASEMENT2 CORNER INSTALLATION 1 STRAIGHT OUT INSTALLATION3 BASEMENT INSTALLATION ULTRA FLAME DV “0” Clearance Fireplace VENTING SYSTEMVENT TERMINAL, BASEMENT INSTALLATION OPTIONAL BLOWER INSTALLATION VENT TERMINAL, ROOF INSTALLATIONBURNER REMOVAL AND INSTALLATION GLASS FRONT REMOVAL, CLEANING AND INSTALLATIONEMBER KIT INSTALLATION LOG INSTALLATION LOUVRE INSTALLATION 1.Remove the glass front assembly OPTIONAL REFRACTORY PANEL INSTALLATION6.Install the glass front assembly ULTRA FLAME DV “0” Clearance FireplaceNatural Gas Pressure Settings ADJUSTMENTSPropane Pressure Settings ELEVATIONRemember to replace all covers ADJUSTING THE GAS PRESSUREWALL THERMOSTAT ADJUSTING AIR SHUTTEROPTIONAL PARTS REPLACEMENT PARTSITEM DESCRIPTION ITEM DESCRIPTIONDROLET STOVES AND FIREPLACES INC LIMITED 5 YEAR WARRANTY