Hampton Direct H15-LP1, H15-NG1 Planning Your Venting Installation, Kit #640-944 Kit #380-946

Page 21

INSTALLATION

RESIDENTIAL AND MANUFACTURED HOMES / MOBILE HOMES

MINIMUM HORIZONTAL TERMINATION INSTALLATIONS

Planning Your Venting Installation

See the "Exterior Vent Terminal Locations" section for requirements.

When planning your installation, it will be nec- essary to select the proper length of vent pipe for your particular requirements. Determine the minimum clearance to combustibles from the rear of the unit to the wall. It is also important to note the wall thickness. Before cutting the vent hole through the wall ensure that ALL vent and termination clearances (Refer to the "Exterior Vent Terminal Locations" section) will be met.

*Ifthisisanoutsidecorner,theminimumdistance between the vent and the outside corner is 6" (15cm). See "F" on the diagram in the "Exterior Vent Terminal Locations" section.

You will require the following components with your new Hampton® Direct Vent Freestanding Gas Stove. Please review your product to make sure you have everything you need. In the event that you are missing any part, contact your dealer. Decorative brass or chrome trim kits are available from Simpson Dura-Vent for their wall thimbles, as well as a square wall thimble cover.

Note: These are the minimum pieces required. Other parts may be required for your par- ticular installation.

NOTE: Ensure compliance with the outside vent terminal location before cutting hole as both dimensions must be met.

Kit #640-944

Kit #380-946

Minimum components for a Horizontal Installation:

640-944 Horizontal Termination Kit which includes:

16-5/8" Dia. x 18" Black Pipe

14" Dia. x 18" Aluminum Vent

1946-202 Wall Penetration Heat Shield (Wall Thimble) (2 pcs)

1640-530/P Riser Vent Terminal

1640-545/P Decorative Wall Trim (Black)

1948-128 Tube Mill-Pac Screws

380-946 Horizontal Termination Kit which includes:

16-5/8" Dia. x 12" Black Pipe

14" Dia. x 12" Aluminum Vent

1946-202 Wall Penetration Heat Shield (Wall Thimble) (2 pcs)

1

946-523/P

AstroCap

1640-545/P Decorative Wall Trim (Black)

1948-128 Tube Mill-Pac Screws

Optional Components:

 

 

946-204

45o Elbow - 6-5/8" Black pipe

946-523/P

AstroCap

 

and 4" Aluminum Vent

946-206

Vinyl Siding Standoff (AstroCap)

946-205

Vinyl Siding Shield for Riser Vent

946-506/P

Vent Guard (AstroCap)

 

Terminal

 

 

946-208/P

Vent Guard (Riser Vent Terminal)

 

 

940

Square Wall Thimble Cover*

 

 

981Snorkel Termination (36")*

982Snorkel Termination (14")*

942 Wall Penetration

Heat Shield*

* Simpson Dura-Vent Components

Hampton® H15-1 Direct Vent Freestanding Gas Stove

21

Image 21
Contents 918-516a 12/17/07 H15 Direct Vent Gas FireplaceUnit Dimensions HamptonTo the New Owner Table of Contents Safety Label MA Code CO Detector RequirementsSpecifications InstallationImportant Message Save These Instructions Mobile Manufactured Homes After First SaleInstallation Checklist General Safety InformationClearances to Combustibles This includesOptional FAN InstallationManufactured Mobile Home Additional Requirements Fan Kit ContainsRear Plate Wires Lug NutVent Restrictor Position PrecautionsRotating Elbow Remove all 4 screws WashersExterior Vent Terminal Locations Description 6-5/8 Rigid Pipe Cross Reference Chart6-5/8 Rigid Pipe Cross Reference Chart Alternate Rigid Pipe Venting SystemsHorizontal Caps+ H1 With these options, max Horizontal Venting with Two 2 90o ElbowsVertical Venting with Two 2 90o Elbows Min Max Min. pipe length is 30 feet with minFeet total horizontal Venting Arrangements Required Parts Vertical Termination with CO-LINEAR Flex SystemStraight Vertical Terminations DescriptionQty. Description DV Stove Horizontal Vent KITOn a siding cov- ered wall, a vinyl siding standoff Minimum components for a Horizontal Installation Planning Your Venting InstallationKit #640-944 Kit #380-946 640-545/P Decorative Wall Trim Black Tube Mill-Pac ScrewsDURA-VENT Termination KIT Planning Your Dura-Vent InstallationDura-Vent Basic Horizontal Kit # 90o Elbow Wall Thimble Cover Horiz. Sq. Term. CapHorizontal Terminations Below Grade Snorkel InstallationMinimum components for a Dura-Vent Verti- cal Termination Snorkel TerminationsSeal around the outer edge of the Riser Vent Backing Plate Vertical TerminationsContinue to assemble pipe lengths Offset ChartApproved for US Installations Only Vent SystemConverting a Factory Built Metal Chimney Cathedral Ceilings High ElevationGAS Connection Valve Description LPG Conversion Kit Contains Qty Conversion KIT# 381-969 from NG to LPInstallation of the DC Sparker Velcro Inside View LOG SET InstallationRemove Glass Door Left Front Log Right Front LogLogs must be oriented as shown below Connect the wires as per the wiring diagram below Wire Size Max. LengthFinal Check Check for proper draftWiring Diagrams For Propane Units and Units Equipped with DC Spark Boxes Operating Instructions Copy of the Lighting Plate Instructions For Your Safety Read Before LightingMaintenance Instructions MaintenancePilot Adjustment Normal Operating Sounds of GAS AppliancesGlass Replacement General Vent MaintenanceFAN Maintenance LOG ReplacementTo remove valve from valve assembly, continue Installing Valve AssemblyRemoving Valve ScrewsMain Assembly Parts List910-039 Burner & LOG AssemblyHampton H15-1 Direct Vent Freestanding Gas Stove Hampton H15-1 Direct Vent Freestanding Gas Stove Hampton H15-1 Direct Vent Freestanding Gas Stove Conditions WarrantyInstaller Please complete the following information

H15-LP1, H15-NG1 specifications

Hampton Direct has established a reputation for producing innovative and high-quality products, and their H15-NG1 and H15-LP1 appliances are no exceptions. These two models have been thoughtfully designed to cater to different needs while sharing several essential features that promise reliability and performance.

The H15-NG1 is designed as a natural gas appliance, ideal for users who prefer the efficiency and cost-effectiveness of natural gas heating. Its advanced technology ensures that it operates smoothly and efficiently, providing consistent heating without compromising safety. Users can appreciate the integrated safety features, including automated shut-off mechanisms and flame detection systems. The H15-NG1 also has adjustable heat settings, giving users the flexibility to control the temperature according to their requirements.

On the other hand, the H15-LP1 is specifically designed for propane users. This model is perfect for those who utilize propane as a primary energy source in their households. Similar to its counterpart, the H15-LP1 boasts a powerful heating system that can quickly warm up large spaces, making it an excellent choice for both indoor and outdoor applications. It also includes safety features such as a pressure regulator, ensuring a stable flow of propane that enhances both efficiency and safety.

Both the H15-NG1 and H15-LP1 are constructed with durable materials, ensuring longevity and resilience in various conditions. They are easy to install and user-friendly, making them suitable for users of all experience levels.

Another significant feature of both models is their energy efficiency, which not only provides savings on utility bills but also contributes to an eco-friendly lifestyle. They are equipped with innovative heating technology that maximizes heat output while minimizing energy consumption. This focus on sustainability aligns with contemporary standards for energy-efficient home appliances.

In summary, the Hampton Direct H15-NG1 and H15-LP1 offer impressive features and technologies designed to meet diverse heating needs. With a commitment to safety, efficiency, and user convenience, these models stand out as reliable choices for homeowners looking for effective heating solutions. Whether you prefer natural gas or propane, both units promise a blend of performance, durability, and ease of use.