Hampton Direct H15-LP1 Conversion KIT# 381-969 from NG to LP, LPG Conversion Kit Contains Qty

Page 29

INSTALLATION

CONVERSION KIT# 381-969 FROM NG TO LP

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !!

Each Kit contains one LPG Conversion Kit and one DC Sparker Kit.

LPG Conversion Kit Contains:

Qty.

Part #

Description

1904-575 Burner Orifi ce #55

1918-590 Label "Converted to Propane"

1908-528 Red "LPG" label

1904-529 5/3" Allen Key

1910-037 LP Injector (Pilot Orifi ce)

1918-479 Instruction Sheet

DC Sparker Kit Contains:

Qty.

Part #

Description

1820-475 Bracket DC Sparker

1820-476 Bracket DC Sparker

1904-153 Washer #8 External Star

1904-330 Nut 8-32 Hex

1904-438 Plug Nylon 0.750 Hole, Black

1904-531 Bushing Split Plastic

0.500 in.

1904-543 Screw 8-32 x 3/4 Pan Head

2904-553 Screw #8 x 1/2 Type "B",

Black Oxide

1910-073 Spark Generator Battery Holder

1910-074 Spark Generator Switch C/W Wire

1910-078 Battery Size AA

Energizer En91

2910-199 Clip Wire Holder

1910-903 Wire Fan To Power Cord Ground 30 in.

904-781 Velcro Hook, Black

904-782 Velcro Hook, Black

Installation of LPG

Conversion Kit:

3)Remove burner by removing the 2 screws on each side and then slide the burner to the left and lift out.

Screws

Note: Use a magnetic type screwdriver if possible.

Pilot assembly

is now

accessible

for steps the

following

steps.

4)Turn control knob to the “OFF” position.

5)Remove the black protection cap by hand from the high-low knob (Fig.1).

Fig. 1

7)Check that the screw is clean and if necessary remove dirt.

8)Flip the screw (Fig. 3).

Fig.3

9)Using the Allen wrench as shown in Fig.4, rotate the screw clockwise until snug, do not overtighten.

Fig.4

WARNING!

Do not overtighten the screw. Recommended to

grip the wrench by the short side.

10)Verify that if the conversion is from NG to LPG, the screw must be reassembled with the red o-ring visible (Fig. 5).

1)Shut off the gas supply.

2)Lift off Cast Top, remove Cast Front and Glass Door (refer to the glass replace- ment section in the manual) and carefully remove logs and lava rock.

6)Insert a 5/32” or 4mm Allen wrench into the hexagonal key-way of the screw (Fig. 2), rotate it counter- clockwise until it is free and extract it.

Fig.2

Red o-ring visible

Fig.5

LPG Configuration

Hampton® H15-1 Direct Vent Freestanding Gas Stove

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents 918-516a 12/17/07 H15 Direct Vent Gas FireplaceTo the New Owner Unit DimensionsHampton Table of Contents Safety Label MA Code CO Detector RequirementsSpecifications InstallationImportant Message Save These Instructions Mobile Manufactured Homes After First SaleInstallation Checklist General Safety InformationClearances to Combustibles This includesOptional FAN InstallationManufactured Mobile Home Additional Requirements Fan Kit ContainsRear Plate Wires Lug NutVent Restrictor Position PrecautionsRotating Elbow Remove all 4 screws WashersExterior Vent Terminal Locations Description 6-5/8 Rigid Pipe Cross Reference Chart6-5/8 Rigid Pipe Cross Reference Chart Alternate Rigid Pipe Venting SystemsHorizontal Caps+ H1 With these options, max Horizontal Venting with Two 2 90o ElbowsFeet total horizontal Vertical Venting with Two 2 90o ElbowsMin Max Min. pipe length is 30 feet with min Venting Arrangements Required Parts Vertical Termination with CO-LINEAR Flex SystemStraight Vertical Terminations DescriptionQty. Description DV Stove Horizontal Vent KITOn a siding cov- ered wall, a vinyl siding standoff Minimum components for a Horizontal Installation Planning Your Venting InstallationKit #640-944 Kit #380-946 640-545/P Decorative Wall Trim Black Tube Mill-Pac ScrewsDURA-VENT Termination KIT Planning Your Dura-Vent InstallationDura-Vent Basic Horizontal Kit # 90o Elbow Wall Thimble Cover Horiz. Sq. Term. CapHorizontal Terminations Below Grade Snorkel InstallationMinimum components for a Dura-Vent Verti- cal Termination Snorkel TerminationsSeal around the outer edge of the Riser Vent Backing Plate Vertical TerminationsContinue to assemble pipe lengths Offset ChartConverting a Factory Built Metal Chimney Approved for US Installations OnlyVent System GAS Connection Cathedral CeilingsHigh Elevation Valve Description LPG Conversion Kit Contains Qty Conversion KIT# 381-969 from NG to LPInstallation of the DC Sparker Velcro Inside View LOG SET InstallationRemove Glass Door Left Front Log Right Front LogLogs must be oriented as shown below Connect the wires as per the wiring diagram below Wire Size Max. LengthFinal Check Check for proper draftWiring Diagrams For Propane Units and Units Equipped with DC Spark Boxes Operating Instructions Copy of the Lighting Plate Instructions For Your Safety Read Before LightingMaintenance Instructions MaintenancePilot Adjustment Normal Operating Sounds of GAS AppliancesGlass Replacement General Vent MaintenanceFAN Maintenance LOG ReplacementTo remove valve from valve assembly, continue Installing Valve AssemblyRemoving Valve ScrewsMain Assembly Parts List910-039 Burner & LOG AssemblyHampton H15-1 Direct Vent Freestanding Gas Stove Hampton H15-1 Direct Vent Freestanding Gas Stove Hampton H15-1 Direct Vent Freestanding Gas Stove Conditions WarrantyInstaller Please complete the following information

H15-LP1, H15-NG1 specifications

Hampton Direct has established a reputation for producing innovative and high-quality products, and their H15-NG1 and H15-LP1 appliances are no exceptions. These two models have been thoughtfully designed to cater to different needs while sharing several essential features that promise reliability and performance.

The H15-NG1 is designed as a natural gas appliance, ideal for users who prefer the efficiency and cost-effectiveness of natural gas heating. Its advanced technology ensures that it operates smoothly and efficiently, providing consistent heating without compromising safety. Users can appreciate the integrated safety features, including automated shut-off mechanisms and flame detection systems. The H15-NG1 also has adjustable heat settings, giving users the flexibility to control the temperature according to their requirements.

On the other hand, the H15-LP1 is specifically designed for propane users. This model is perfect for those who utilize propane as a primary energy source in their households. Similar to its counterpart, the H15-LP1 boasts a powerful heating system that can quickly warm up large spaces, making it an excellent choice for both indoor and outdoor applications. It also includes safety features such as a pressure regulator, ensuring a stable flow of propane that enhances both efficiency and safety.

Both the H15-NG1 and H15-LP1 are constructed with durable materials, ensuring longevity and resilience in various conditions. They are easy to install and user-friendly, making them suitable for users of all experience levels.

Another significant feature of both models is their energy efficiency, which not only provides savings on utility bills but also contributes to an eco-friendly lifestyle. They are equipped with innovative heating technology that maximizes heat output while minimizing energy consumption. This focus on sustainability aligns with contemporary standards for energy-efficient home appliances.

In summary, the Hampton Direct H15-NG1 and H15-LP1 offer impressive features and technologies designed to meet diverse heating needs. With a commitment to safety, efficiency, and user convenience, these models stand out as reliable choices for homeowners looking for effective heating solutions. Whether you prefer natural gas or propane, both units promise a blend of performance, durability, and ease of use.
Top Page Image Contents