Regency Wraps P36-LPG4, P36-NG4 Copy of the Lighting Plate Instructions, Maintenance Instructions

Page 32

OPERATING INSTRUCTIONS

COPY OF THE LIGHTING PLATE INSTRUCTIONS

FORYOURSAFETYREADBEFORELIGHTING

This appliance must be installed in accordance with local codes, if any; if not, follow the current CAN1-B149/ANSI Z 223.1 (Australia: AS5601-2004, New Zealand: NZS 5261)

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss oflife.Improperinstallation,adjustment,alteration,serviceormaintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or gas supplier.

MAINTENANCE

INSTRUCTIONS

1) Alwaysturnoffthegasvalvebeforecleaning.

For relighting, refer to lighting instructions.

Keep the burner and control compartment

clean by brushing and vacuuming at least

once a year. When cleaning the logs, use a

soft clean paint brush as the logs are fragile

and easily damaged.

2) Clean appliance and door with a damp

cloth (never when unit is hot). Never use

an abrasive cleaner. The glass should be

cleaned with a gas fi replace glass cleaner.

The glass should be cleaned when it

A)This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B)BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

-Do not try to light any appliance

-Do not touch any electric switch, do not use any phone in your building

-Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

C)Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D)Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

starts looking cloudy.

3) The heater is fi nished in a heat resistant

paint and should only be refinished with heat

resistant paint. Regency® uses StoveBright

Paint - Metallic Black #6309.

4) Make a periodic check of burner for proper

position and condition. Visually check the

flame of the burner periodically, making sure

the fl ames are steady; not lifting or fl oating.

If there is a problem, call an authorized

service person.

5) The appliance and fl ueing system must be

inspected before use, and at least annually,

by an authorized fi eld service person, to

ensure that the fl ow of combustion and

ventilation air is not obstructed.

CAUTION:Hotwhileinoperation.Donottouch.SevereBurnsmayresult.Due to high surface temperatures keep children, clothing and furniture, gasoline and other liquids having fammable vapors away. Keep burner and control compartment clean. See installation and operating instructions

accompanying appliance.

LIGHTINGINSTRUCTIONS

STOP! Read the safety information above on this label.

1)Push in gas control knob slightly and turn to “PILOT” position.

2)Push in control knob all the way and hold in until the pilot lights up. Continue to hold the control knob in for about 20 seconds after the pilot is lit. Release knob.

3) Push in gas control knob slightly and

Gas Inlet

turn to "ON" position.

4) Turn ON the flame switch.

TO TURN OFF GAS APPLIANCE

You may shut off the pilot during prolonged non use periods to conserve fuel.

1)Turn OFF the flame switch.

2)Push in gas control knob slightly and turn to "OFF" position.

DO NOT REMOVE THIS INSTRUCTION PLATE

918-253a

Note: Never operate the appliance without the glass properly secured in place.

6)Donotusethisapplianceifanyparthasbeen under water. Immediately call an authorized service technician to inspect the appliance and to replace nay part of the control system and any gas control which has been under water.

7)Verify operation after servicing.

General Flue Maintenance

Conduct an inspection of the fl ueing system semi-annually. Recommended areas to inspect as follows:

1)Check the Flueing System for corrosion in areas that are exposed to the elements. These will appear as rust spots or streaks, and in extreme cases, holes. These components should be replaced immediately.

2)Remove the Cap, and shine a fl ashlight down the Flue. Remove any bird nests, or other foreign material.

32

Regency® P36-4 Gas Log Fireplace

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Manual Please Keep These Instructions For Future ReferenceTo the NEW Owner Table of Contents Data Badge Data Badge Note Regency units areInstallation General Safety InformationInstallation Checklist Important MessageClearances Locating Your GAS FireplaceManufactured Mobile Home Additional Requirements Diagram Combustible MantelsStandard Framing Dimensions Framing Dimensions with Premium Flush Front OptionMantel LEG Clearances Framing FinishingUnit Assembly Prior to Installation Top Standoff AssemblyPremium Flush Front Spacer Installation Flueing IntroductionExterior Flue Termination Locations Clearance k in mmFlueing Regency Direct Vent System Flex Horizontal Terminations OnlySimpson DURA-VENT Flueing Simpson DURA-VENT Flueing Components ListFlueing Arrangements Horizontal Terminations Regency Direct Vent System FlexRegency CO Axial Flue System Flex Flueing Arrangements Vertical Terminations Simpson DURA-VENT CO Axial Flue GS System LPG & NG45o elbows allowed Horizontal Terminations Dura-VentVertical Terminations Offset ChartThis allows for small adjustments Installed Conversion Kit Contains QtyShut off the gas supply Remove the louvers and bay door if it isGAS Line Installation Pilot AdjustmentAeration Adjustment GAS Pipe Pressure TestingVermiculite LOG SET InstallationOptional Brick Panels Rear Bracket 5th Grate TabBracket Bracket Notch 2nd Grate TabFlush Louvres Optional Flush TrimPlace embers in these 3 locations On the burner tray EmbersPremium Flush Front Installation Louver TabThermodisc Plate Thermodisc Cover Grommet Wire Cover Wall Thermostat Wall SwitchRemote Control Wiring Standard WiringWiring with Premium Flush Front Option Operating Instructions Optional FANOperating Instructions To Remove the FanNormal Operating Sounds of GAS Appliances Lighting ProcedureFirst Fire Copy of the Lighting Plate Instructions Maintenance InstructionsGeneral Flue Maintenance Maintenance Installing Valve Diagram 2 Rear Log Stand Valve Tray AssemblyRemoving Valve ScrewsParts List Main AssemblyBurner Assembly & LOG SET BAY Front Assembly Flush Front Accessories DescriptionPremium Flush Front Assembly Cast Faceplate Assembly Regency P36-4 Gas Log Fireplace Regency P36-4 Gas Log Fireplace Warranty ConditionsExclusions General

P36-NG4, P36-LPG4 specifications

Regency Wraps has made a significant mark in the world of grill accessories with its high-quality products, particularly the P36-LPG4 and P36-NG4 wraps. These wraps are designed specifically for grill enthusiasts who value durability, functionality, and aesthetic appeal in their cooking equipment.

The P36-LPG4 model is tailored for those who prefer liquid propane as their fuel source. It boasts a robust construction that ensures longevity and resilience against the elements. One of the key features of the P36-LPG4 is its heat-resistant fabric, which is crafted to withstand high temperatures without compromising the integrity of the wrap. This makes it an ideal choice for situations where intense heat is a norm, providing both safety and performance.

On the other hand, the P36-NG4 model caters to natural gas users. Similar to its LPG counterpart, the P36-NG4 is engineered to handle the rigors of outdoor grilling while offering a stylish appearance. The wrap is designed to fit a range of traditional grills, ensuring a snug yet flexible fit that protects the grill from dust, debris, and harsh weather conditions.

Both models feature advanced technologies, including UV resistance, which helps in maintaining the vibrant colors and quality of the fabric over time. This is crucial for outdoor gear that often faces prolonged exposure to the sun, preserving the product's aesthetic charm as well as its functional attributes.

The characteristics of the P36-LPG4 and P36-NG4 wraps extend beyond mere protection. They are equipped with user-friendly features such as easy installation; most users can simply slip the wrap over their grill in seconds. The wraps are also lightweight, which enhances portability for grillers who like to take their equipment on the go.

Furthermore, both wraps are designed with ease of maintenance in mind. They can be cleaned effortlessly, ensuring that grill enthusiasts can maintain their equipment in pristine condition without excessive effort or time.

In summary, Regency Wraps offers the P36-LPG4 and P36-NG4 models as the ultimate solution for grill protection, combining style with superior functionality. With their durable construction, advanced technologies, and user-friendly design, these wraps are a worthy investment for any grilling aficionado looking to enhance their outdoor cooking experience.
Top Page Image Contents