Regency Wraps P36-NG4, P36-LPG4 manual Unit Assembly Prior to Installation, Flueing Introduction

Page 9

INSTALLATION

UNIT ASSEMBLY

PRIOR TO

INSTALLATION

The Top Facing Support, the Side Nailing Strips and the 2 Top Standoffs must be correctly positioned and attached to the top before unit is slipped into position.

Top Standoff Assembly

The top standoffs are shipped in a fl at position and must be folded into shape and attached.

1)Remove the standoffs from the fi replace top.

2)Take each standoff and bend into the correct shape. Bend up at the bend lines until the screw holes in the standoff and the pre- punched screw holes on the fi replace top line up.

3)Attach the standoff securely to the top with 2 screws per standoff (on opposite corners).

1)Mount Top Facing Support using the 3 supplied screws into the three pre-punched screw holes on the top front of the unit. Use hole positions A, B, or C depending on your facing depth.

Premium Flush Front

Spacer Installation

Before the unit is slid into position, install the provided spacers to the side of the fireplace as follows;

1)Align the screw locations on spacer with screw locations on the side of the fi rebox and secure in place using 3 screws.

2)Repeat for other side.

NOTE: The side nailing strips are to be in- stalled to the spacer after the spacer is attached to the unit.

Top Facing Support and

Side Nailing Strips

Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the

finished surface to be fl ush with the front of the unit. Total facing thickness can vary from 1/2" (13mm) to 1-1/4" (32mm) thick.

TheTopFacingSupport&SideNailingStripscan be mounted in 3 different positions depending on the thickness of the facing material.

Screw

Facing Material

Position

Depth

 

 

 

 

 

 

A

1/2"

/ 13mm

B

7/8"

/ 22mm

C*

1-1/4"

/ 32mm

*For "C" screw position the top facing support is reversed.

"C" Screw Position:

For a facing material depth of 1-1/4" (32mm), the top facing support must be reversed.

2)Use the same screw hole position for the Side Nailing Strips as was used for the Top Facing Support. Attach each side nailing strip using 3 screws.

Spacer

Left Side Shown

FLUEING

INTRODUCTION

The P36 uses the "balanced fl ue" technology Co Axial system. The inner liner fl ues products of combustion to the outside while the outer liner draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.

Note: These flue pipes must not be

connected to any other appliance.

The gas appliance and fl ue system must be

flued directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas burning appliance. Each Co Axial Flue gas appliance must use it's own separate fl ue system. Common fl ue systems are prohibited.

Regency® P36-4 Gas Log Fireplace

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Please Keep These Instructions For Future Reference ManualTo the NEW Owner Table of Contents Data Badge Note Regency units are Data BadgeGeneral Safety Information InstallationInstallation Checklist Important MessageLocating Your GAS Fireplace Manufactured Mobile Home Additional RequirementsClearances Combustible Mantels DiagramFraming Dimensions with Premium Flush Front Option Standard Framing DimensionsMantel LEG Clearances Framing FinishingTop Standoff Assembly Unit Assembly Prior to InstallationPremium Flush Front Spacer Installation Flueing IntroductionClearance k in mm Exterior Flue Termination LocationsRegency Direct Vent System Flex Horizontal Terminations Only FlueingSimpson DURA-VENT Flueing Components List Simpson DURA-VENT FlueingRegency Direct Vent System Flex Flueing Arrangements Horizontal TerminationsRegency CO Axial Flue System Flex Simpson DURA-VENT CO Axial Flue GS System LPG & NG Flueing Arrangements Vertical Terminations45o elbows allowed Dura-Vent Horizontal TerminationsOffset Chart This allows for small adjustmentsVertical Terminations Conversion Kit Contains Qty InstalledShut off the gas supply Remove the louvers and bay door if it isPilot Adjustment GAS Line InstallationAeration Adjustment GAS Pipe Pressure TestingLOG SET Installation Optional Brick PanelsVermiculite 5th Grate Tab Rear BracketBracket Bracket Notch 2nd Grate TabOptional Flush Trim Flush LouvresPlace embers in these 3 locations On the burner tray EmbersLouver Tab Premium Flush Front InstallationThermodisc Plate Thermodisc Cover Grommet Wire Cover Wall Switch Remote ControlWall Thermostat Standard Wiring WiringWiring with Premium Flush Front Option Optional FAN Operating InstructionsOperating Instructions To Remove the FanLighting Procedure First FireNormal Operating Sounds of GAS Appliances Maintenance Instructions General Flue MaintenanceCopy of the Lighting Plate Instructions Maintenance Diagram 2 Rear Log Stand Valve Tray Assembly Installing ValveRemoving Valve ScrewsMain Assembly Parts ListBurner Assembly & LOG SET BAY Front Assembly Description Flush Front AccessoriesPremium Flush Front Assembly Cast Faceplate Assembly Regency P36-4 Gas Log Fireplace Regency P36-4 Gas Log Fireplace Conditions WarrantyExclusions General

P36-NG4, P36-LPG4 specifications

Regency Wraps has made a significant mark in the world of grill accessories with its high-quality products, particularly the P36-LPG4 and P36-NG4 wraps. These wraps are designed specifically for grill enthusiasts who value durability, functionality, and aesthetic appeal in their cooking equipment.

The P36-LPG4 model is tailored for those who prefer liquid propane as their fuel source. It boasts a robust construction that ensures longevity and resilience against the elements. One of the key features of the P36-LPG4 is its heat-resistant fabric, which is crafted to withstand high temperatures without compromising the integrity of the wrap. This makes it an ideal choice for situations where intense heat is a norm, providing both safety and performance.

On the other hand, the P36-NG4 model caters to natural gas users. Similar to its LPG counterpart, the P36-NG4 is engineered to handle the rigors of outdoor grilling while offering a stylish appearance. The wrap is designed to fit a range of traditional grills, ensuring a snug yet flexible fit that protects the grill from dust, debris, and harsh weather conditions.

Both models feature advanced technologies, including UV resistance, which helps in maintaining the vibrant colors and quality of the fabric over time. This is crucial for outdoor gear that often faces prolonged exposure to the sun, preserving the product's aesthetic charm as well as its functional attributes.

The characteristics of the P36-LPG4 and P36-NG4 wraps extend beyond mere protection. They are equipped with user-friendly features such as easy installation; most users can simply slip the wrap over their grill in seconds. The wraps are also lightweight, which enhances portability for grillers who like to take their equipment on the go.

Furthermore, both wraps are designed with ease of maintenance in mind. They can be cleaned effortlessly, ensuring that grill enthusiasts can maintain their equipment in pristine condition without excessive effort or time.

In summary, Regency Wraps offers the P36-LPG4 and P36-NG4 models as the ultimate solution for grill protection, combining style with superior functionality. With their durable construction, advanced technologies, and user-friendly design, these wraps are a worthy investment for any grilling aficionado looking to enhance their outdoor cooking experience.
Top Page Image Contents