Regency Wraps P36-NG4, P36-LPG4 Important Message, Before YOU Start, Installation Checklist

Page 5

INSTALLATION

IMPORTANT MESSAGE

SAVE THESE INSTRUCTIONS

TheP36-NGorP36-LPGRoomSealedFireplace must be installed in accordance with AS5601- 2004andNZS52615261andtheseinstructions. Carefully read all the instructions in this manual

first. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation. It is the responsibility of the installer to ensure this fi replace is installed in compliance with manufacturer's instructions and all applicable codes.

BEFORE YOU START

NOTE: NOT INTENDED AS A FIREPLACE INSERT.

INSTALLATION AND REPAIR SHOULD BE DONE BY A AUTHORISED SERVICE PERSON. THE APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT LEAST ANNUALLYBYANAUTHORISED SERVICE PERSON. MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING MATERIAL, ETC. IT IS IMPERATIVE THAT CONTROL COMPARTMENTS, BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE LOCATED OUT OFTRAFFICANDAWAYFROMFURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS APPLIANCECORRECTLYWILLVOIDYOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE.

CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.

YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.

CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE. DO NOT USE AEROSOLS IN THE VICINITY OF THIS APPLIANCE.

GENERAL SAFETY

INFORMATION

1)The appliance shall be installed in accordance with the manufacturer's installation instructions,local gas fi tting regulations, municipal building codes, water supply regulations, electrical wiring regulations, with AS5601-2004 (AGA gas installation code) NZS 5261 (New Zealand)

2)Installation and repair should be done ONLY by an authorised person.

3)THISAPPLIANCEISNOTINTENDEDASA FIREPLACE INSERT. DO NOT CONNECT TO MASONARY FLUE.

4)This appliance must be connected to the specified flue and termination cap to the outside of the building envelope. Never flue to another room or inside a building. Make sure that the flue is fitted as per Flueing instructions.

5)Inspect the fl ueing system annually for blockage and any signs of deterioration.

6)Flueing terminals shall not be recessed into a wall or siding.

7)Any safety glass removed for servicing must be replaced prior to operating the appliance.

8)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fi replace.

9)Wearglovesandsafetyglassesforprotection while doing required maintenance.

10)Be aware of electrical wiring locations in walls and ceilings when cutting holes for termination.

11)Under no circumstances should this appliance be modifi ed. Parts that have to be removed for servicing should be replaced prior to operating this appliance.

12)Installation and any repairs to this appliance should be done by an authorised service person.Anauthorisedservicepersonshould be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually.

13)Do not slam shut or strike the glass door.

14)Under no circumstances should any solid fuels (wood, paper, cardboard, coal, etc.) be used in this appliance.

15)The appliance area must be kept clear and free of combustible materials, (gases and other fl ammable vapours and liquids).

INSTALLATION

CHECKLIST

1)Locate appliance

a)Locate Your Gas Fireplace

b)Clearances

c)Combustible Mantels

d)Framing & Finishing

2)Assemble Top Standoffs and Top Facing Support and Side Nailing Strips, refer to section "UnitAssembly Prior to Installation". (NOTE: must be done before installing unit into fi replace.)

3)Install fl ue (Refer to section "Simpson Dura- vent Flueing").

4)Make gas and electrical connections. Test the pilot. Must be as per diagram. Refer to section "Pilot Adjustment."

5)Install standard and optional features. Refer to the following sections:

a. Brick Panels b. Log Set

c. Flush Door

d. Premium Flush Front e. Bay Door

f. Hampton® Cast Faceplate g. Hampton® Cast Grills

h. Wall Switch

i. Remote Control j. Wall Thermostat k. Fan

6)Final check.

Before leaving this unit with the customer, the installer must ensure that the appliance is

firing correctly and operation fully explained to customer.

This includes:

1)Clocking the appliance to ensure the correct fi ring rate (rate noted on label 30,000 Btu/h) after burning appliance for 15 minutes.

2)Ifrequired,adjustingtheprimaryairtoensure that the fl ame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.

Regency® P36-4 Gas Log Fireplace

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Please Keep These Instructions For Future Reference ManualTo the NEW Owner Table of Contents Data Badge Note Regency units are Data BadgeGeneral Safety Information InstallationInstallation Checklist Important MessageClearances Locating Your GAS FireplaceManufactured Mobile Home Additional Requirements Combustible Mantels DiagramFraming Dimensions with Premium Flush Front Option Standard Framing DimensionsMantel LEG Clearances Framing FinishingTop Standoff Assembly Unit Assembly Prior to InstallationPremium Flush Front Spacer Installation Flueing IntroductionClearance k in mm Exterior Flue Termination LocationsRegency Direct Vent System Flex Horizontal Terminations Only FlueingSimpson DURA-VENT Flueing Components List Simpson DURA-VENT FlueingRegency Direct Vent System Flex Flueing Arrangements Horizontal TerminationsRegency CO Axial Flue System Flex Simpson DURA-VENT CO Axial Flue GS System LPG & NG Flueing Arrangements Vertical Terminations45o elbows allowed Dura-Vent Horizontal TerminationsVertical Terminations Offset ChartThis allows for small adjustments Conversion Kit Contains Qty InstalledShut off the gas supply Remove the louvers and bay door if it isPilot Adjustment GAS Line InstallationAeration Adjustment GAS Pipe Pressure TestingVermiculite LOG SET InstallationOptional Brick Panels 5th Grate Tab Rear BracketBracket Bracket Notch 2nd Grate TabOptional Flush Trim Flush LouvresPlace embers in these 3 locations On the burner tray EmbersLouver Tab Premium Flush Front InstallationThermodisc Plate Thermodisc Cover Grommet Wire Cover Wall Thermostat Wall SwitchRemote Control Standard Wiring WiringWiring with Premium Flush Front Option Optional FAN Operating InstructionsOperating Instructions To Remove the FanNormal Operating Sounds of GAS Appliances Lighting ProcedureFirst Fire Copy of the Lighting Plate Instructions Maintenance InstructionsGeneral Flue Maintenance Maintenance Diagram 2 Rear Log Stand Valve Tray Assembly Installing ValveRemoving Valve ScrewsMain Assembly Parts ListBurner Assembly & LOG SET BAY Front Assembly Description Flush Front AccessoriesPremium Flush Front Assembly Cast Faceplate Assembly Regency P36-4 Gas Log Fireplace Regency P36-4 Gas Log Fireplace Conditions WarrantyExclusions General

P36-NG4, P36-LPG4 specifications

Regency Wraps has made a significant mark in the world of grill accessories with its high-quality products, particularly the P36-LPG4 and P36-NG4 wraps. These wraps are designed specifically for grill enthusiasts who value durability, functionality, and aesthetic appeal in their cooking equipment.

The P36-LPG4 model is tailored for those who prefer liquid propane as their fuel source. It boasts a robust construction that ensures longevity and resilience against the elements. One of the key features of the P36-LPG4 is its heat-resistant fabric, which is crafted to withstand high temperatures without compromising the integrity of the wrap. This makes it an ideal choice for situations where intense heat is a norm, providing both safety and performance.

On the other hand, the P36-NG4 model caters to natural gas users. Similar to its LPG counterpart, the P36-NG4 is engineered to handle the rigors of outdoor grilling while offering a stylish appearance. The wrap is designed to fit a range of traditional grills, ensuring a snug yet flexible fit that protects the grill from dust, debris, and harsh weather conditions.

Both models feature advanced technologies, including UV resistance, which helps in maintaining the vibrant colors and quality of the fabric over time. This is crucial for outdoor gear that often faces prolonged exposure to the sun, preserving the product's aesthetic charm as well as its functional attributes.

The characteristics of the P36-LPG4 and P36-NG4 wraps extend beyond mere protection. They are equipped with user-friendly features such as easy installation; most users can simply slip the wrap over their grill in seconds. The wraps are also lightweight, which enhances portability for grillers who like to take their equipment on the go.

Furthermore, both wraps are designed with ease of maintenance in mind. They can be cleaned effortlessly, ensuring that grill enthusiasts can maintain their equipment in pristine condition without excessive effort or time.

In summary, Regency Wraps offers the P36-LPG4 and P36-NG4 models as the ultimate solution for grill protection, combining style with superior functionality. With their durable construction, advanced technologies, and user-friendly design, these wraps are a worthy investment for any grilling aficionado looking to enhance their outdoor cooking experience.
Top Page Image Contents