Regency Wraps P36-LPG4, P36-NG4 manual Removing Valve, Installing Valve, Screws

Page 34

MAINTENANCE

REMOVING VALVE

1)Shut off the gas supply.

2)Remove the louvres (and bay door if it is on).

3)Open the fl ush door and remove the door.

4)Remove the logs.

5)Remove the burner/grate assembly by removing the two Phillips head screws and then lift the burner assembly out.

Diagram 1: Remove the left and right screws and then lift out the burner/grate assembly.

6)Remove the rear log stand by removing the 2 screws.

screws

Rear Log Stand

10)Undo the pilot tube from the valve with a 7/16" spanner.

11)Undo the quick drop out thermocouple nut on the valve with a 9mm (metric) spanner.

12)Remove the Piezo igniter wire and push button assembly.

13)Undo the "gas out" fl are nut with a 13/16" spanner.

14)Undo the "gas out" fl are fitting with an 11/16" spanner.

15)Remove the 4 Phillips head screws from the sides of the valve bracket and remove valve.

Hint: If you are using black pipe, ensure that there is a union by the valve, otherwise removal will be almost impossible.

INSTALLING VALVE

1)Attach the valve to the valve bracket with the 4 (m5x8 metric) screws provided.

2)Reconnect the "gas out" fl are fi tting with an 11/16" spanner.

3)Reconnect the "gas out" fl are nut with a 13/16" spanner.

4)Install piezo ignitor push button assembly and reconnect wire.

5)Reconnect the quick drop out thermocouple nut with a 9mm spanner.

6)Reconnect the pilot tube nut with a 7/16" spanner.

7) Scrape off the old gasket from the floor of the

fi rebox and from the valve tray assembly.

8)Install a new gasket and reinstall the valve tray assembly.

Note: Failure to install a new gasket may severely affect the appliance performance.

9)

Reinstall the 10 hold down screws.

10)

Hook up the 2 TP and 2 TH wires to the

 

appropriate connections on the valve.

11)

Reinstall the front log stand.

12)

Install Burner/grate assembly

13)

Hook up the gas line and check for gas

 

leaks with a soap and water solution or a

 

gas leak detector. (Do not use open fl ame

 

for leak testing.)

14)

Fire up the unit temporarily

15)

Check the manifold pressure.

16)

Reinstall the logs and brick panels as

 

needed.

17)

Close the door and replace the louvres.

18)

Fire up the unit again and check for proper

screws

Valve Tray Assembly

Diagram 2: Rear Log Stand and

Valve Tray Assembly

7)Disconnect the inlet gas line. See diagram 2.

8)Disconnect the 2 TP wires and the 2 TH wires from the valve.

9)Removethe10Phillipsheadscrewssecuring the valve tray assembly in place (diagram 2) and then lift the entire assembly out diagram 3).

fl ame appearance and glow on logs.

34

Regency® P36-4 Gas Log Fireplace

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Manual Please Keep These Instructions For Future ReferenceTo the NEW Owner Table of Contents Data Badge Data Badge Note Regency units areInstallation Checklist InstallationGeneral Safety Information Important MessageManufactured Mobile Home Additional Requirements Locating Your GAS FireplaceClearances Diagram Combustible MantelsMantel LEG Clearances Standard Framing DimensionsFraming Dimensions with Premium Flush Front Option Framing FinishingPremium Flush Front Spacer Installation Unit Assembly Prior to InstallationTop Standoff Assembly Flueing IntroductionExterior Flue Termination Locations Clearance k in mmFlueing Regency Direct Vent System Flex Horizontal Terminations OnlySimpson DURA-VENT Flueing Simpson DURA-VENT Flueing Components ListFlueing Arrangements Horizontal Terminations Regency Direct Vent System FlexRegency CO Axial Flue System Flex Flueing Arrangements Vertical Terminations Simpson DURA-VENT CO Axial Flue GS System LPG & NG45o elbows allowed Horizontal Terminations Dura-VentThis allows for small adjustments Offset ChartVertical Terminations Shut off the gas supply InstalledConversion Kit Contains Qty Remove the louvers and bay door if it isAeration Adjustment GAS Line InstallationPilot Adjustment GAS Pipe Pressure TestingOptional Brick Panels LOG SET InstallationVermiculite Bracket Bracket Notch Rear Bracket5th Grate Tab 2nd Grate TabPlace embers in these 3 locations On the burner tray Flush LouvresOptional Flush Trim EmbersPremium Flush Front Installation Louver TabThermodisc Plate Thermodisc Cover Grommet Wire Cover Remote Control Wall SwitchWall Thermostat Wiring Standard WiringWiring with Premium Flush Front Option Operating Instructions Operating InstructionsOptional FAN To Remove the FanFirst Fire Lighting ProcedureNormal Operating Sounds of GAS Appliances General Flue Maintenance Maintenance InstructionsCopy of the Lighting Plate Instructions Maintenance Removing Valve Installing ValveDiagram 2 Rear Log Stand Valve Tray Assembly ScrewsParts List Main AssemblyBurner Assembly & LOG SET BAY Front Assembly Flush Front Accessories DescriptionPremium Flush Front Assembly Cast Faceplate Assembly Regency P36-4 Gas Log Fireplace Regency P36-4 Gas Log Fireplace Exclusions WarrantyConditions General

P36-NG4, P36-LPG4 specifications

Regency Wraps has made a significant mark in the world of grill accessories with its high-quality products, particularly the P36-LPG4 and P36-NG4 wraps. These wraps are designed specifically for grill enthusiasts who value durability, functionality, and aesthetic appeal in their cooking equipment.

The P36-LPG4 model is tailored for those who prefer liquid propane as their fuel source. It boasts a robust construction that ensures longevity and resilience against the elements. One of the key features of the P36-LPG4 is its heat-resistant fabric, which is crafted to withstand high temperatures without compromising the integrity of the wrap. This makes it an ideal choice for situations where intense heat is a norm, providing both safety and performance.

On the other hand, the P36-NG4 model caters to natural gas users. Similar to its LPG counterpart, the P36-NG4 is engineered to handle the rigors of outdoor grilling while offering a stylish appearance. The wrap is designed to fit a range of traditional grills, ensuring a snug yet flexible fit that protects the grill from dust, debris, and harsh weather conditions.

Both models feature advanced technologies, including UV resistance, which helps in maintaining the vibrant colors and quality of the fabric over time. This is crucial for outdoor gear that often faces prolonged exposure to the sun, preserving the product's aesthetic charm as well as its functional attributes.

The characteristics of the P36-LPG4 and P36-NG4 wraps extend beyond mere protection. They are equipped with user-friendly features such as easy installation; most users can simply slip the wrap over their grill in seconds. The wraps are also lightweight, which enhances portability for grillers who like to take their equipment on the go.

Furthermore, both wraps are designed with ease of maintenance in mind. They can be cleaned effortlessly, ensuring that grill enthusiasts can maintain their equipment in pristine condition without excessive effort or time.

In summary, Regency Wraps offers the P36-LPG4 and P36-NG4 models as the ultimate solution for grill protection, combining style with superior functionality. With their durable construction, advanced technologies, and user-friendly design, these wraps are a worthy investment for any grilling aficionado looking to enhance their outdoor cooking experience.
Top Page Image Contents