Regency P42-NG4, P42-LP4 installation manual Removing the FAN Replacing the FAN, Shut the power off

Page 38

MAINTENANCE

REMOVING THE FAN

REPLACING THE FAN

REMOVING VALVE

1)Shut the power off.

2)Remove the bottom louver.

3)Removeterminalblockcoveranddisconnect the fan wires.

4)Disconnect white fan wire from the terminal block.

5)Disconnect black fan wire from the thermodisc.

6)Disconnect fan ground wire.

7)Lift the fan off the two mounting studs and pull out.

IMPORTANT:

These fans collect a lot of dust from within your home. Ensure you maintain these fan motors on a regular basis by vacuuming out the fan squirrel cages.

Grounding lug detail

1)Shut the power off.

2)Remove the bottom louver. Slide the fan in and push it towards the rear of the unit and slip it over the two mounting studs.

3)Remove the terminal block cover. Wire the fan to the terminal block as shown in the wiring diagram below.

4)Connect white wire from fan to neutral of terminal block.

5)Connect black wire from fan to the thermodisc.

6)Connect fan ground wire. Refer to wiring diagram.

7)Attach the ground wire to the fi replace (ground lug provided).

8)Attach the terminal block cover.

Note: A 120 Volt AC power cord should be installed at rough-in stage so that the power is available. A three wire power cord can be used.

The bearings are lubricated for life. Do not lubricate them. Make sure you vacuum the fan area on a regular basis.

1)Shut off the gas supply.

2)Remove the louvers (and bay door if it is on).

3)Disconnect the inlet gas line.

Note: Be sure to have an 11/16" wrench on the tee to ensure that the whole line is not twisted

4)Disconnect the 2 TP wires and the 2 TH wires from the valve.

5)Remove the Piezo igniter wire.

6)Open and remove the fl ush door.

7)Remove the logs.

8)Remove the burner tube by removing the 3 Phillips head screws and then lift the burner out.

9)Remove the burner grate assembly by removing the 3 Phillips head screws on the feet of the grate assembly.

10)Brush away all the vermiculite and embers from the right hand half of the fi replace.

11)Remove the top and right hand side brick panels.

12)Removethe12Phillipsheadscrewssecuring the valve access plate in place and then lift the entire assembly out.

13)Undo the pilot tube from the valve with a 7/16" wrench.

14)Undo the quick drop out thermocouple nut on the valve with a 9mm wrench.

15)Undo the "gas out" fl are nut with a 13/16" wrench.

16)Undo the "gas out" 90o elbow fl are fi tting with an 11/16" wrench.

17)Remove the 4 Phillips head screws from the sides of the valve bracket and remove valve.

Hint: If you are using black pipe, ensure that there is a union by the valve, otherwise removal will be almost impossible.

38

Regency® P42-4 Zero Clearance Direct Vent Gas Fireplace

Page 37 Page 39
Image 38
Page 37 Page 39
Contents P42 Gas Fireplace 918-523a 03/06/08Information for MOBILE/MANUFACTURED Homes After First Sale To the New OwnerTable of Contents Safety Label Copy of Safety Decal for P42Requirements MA Code CO DetectorInstallation Checklist InstallationGeneral Safety Information Important Message Save These InstructionsHeatwave Optional Duct System KIT Unit Specifications Locating Your GAS FireplaceManufactured Mobile Home Additional Requirements Optional Heat Release KITClearancesmantels Mantel LEG ClearancesVenting Introduction TOP Assembly Nailing StripsFraming Finishing Vent RestrictorExterior Vent Termination Requirements Venting Run of 4 feet6-5/8 Rigid Pipe Cross Reference Chart Description6-5/8 Rigid Pipe Cross Reference Chart Horizontal Rigid Pipe VentingAlternate Termination CapsRigid Pipe Venting Arrangements Horizontal Terminations Vent guard may be required, check local codesFor All Horizontal Terminations 8 outer diameter Regency Flex Vent 4 inner diameterRigid Pipe Venting Arrangements Vertical Terminations Propane & Natural GasVent restrictor #6 must be used Description Vertical Termination With CO-LINEAR Flex SystemRequired Parts Alternate Approved CapsVenting Arrangements Vertical Terminations Snorkel Terminations Below Grade InstallationHorizontal Terminations Diagram Vertical TerminationsFor Regency Direct Vent System Flex Installation ProceduresOffset Chart High Elevation GAS Line InstallationGAS Pipe Pressure Testing System DataAre broken Aeration Brick Panels AdjustmentConditions may occur if the panels FrontPropane LOG SET InstallationNatural GAS Double Screen Doors Standard Flush DoorFlush Louvers Optional Bay Trim Optional BAY DoorBAY Louvers Full Screen Door Frame Installation Full Screen DoorsHinge Location Bottom Grill Hinge Screen Door Do not cut the ground terminal off under Wiring DiagramsAny circumstances Live until the fan is installed For Propane Units and Units Equipped with DC Spark Boxes Thermostat Wire Table Wall SwitchLighting Procedure Operating InstructionsFor Your Safety Read Before Lighting Copy of the Lighting Plate InstructionsMaintenance Instructions MaintenanceShutdown Procedure First FireThermopile Thermocouple GOLD-PLATEDGLASS Louvers ReplacementLOG Replacement Door GlassShut the power off Removing the FAN Replacing the FANInstalling Valve Parts List P42 Main AssemblyP42 Burner & LOG Assembly P42 Flush Door & Louvers P42 BAY Front & Louvers Regency P42-4 Zero Clearance Direct Vent Gas Fireplace Regency P42-4 Zero Clearance Direct Vent Gas Fireplace Regency P42-4 Zero Clearance Direct Vent Gas Fireplace Warranty ConditionsInstaller Please complete the following information

P42-LP4, P42-NG4 specifications

The Regency P42-LP4 and P42-NG4 are two exceptional gas fireplace models that beautifully combine functionality and aesthetic appeal, making them ideal for various home settings. Built with durability and efficiency in mind, these models are equipped with advanced features that enhance user experience.

One of the main highlights of the P42 series is its impressive heating capacity. Both the P42-LP4 and P42-NG4 are designed to deliver substantial warmth, ensuring that spaces of different sizes can be comfortably heated. With a maximum input of up to 40,000 BTUs, these units can effectively warm large living areas, making them perfect for modern homes.

In terms of design, the P42 models boast a sleek and contemporary look. They feature a large viewing area that allows for an expansive flame presentation, inviting warmth and ambiance into your home. The optional polished or brushed stainless steel front and various media options, including glass rocks or logs, provide customization, allowing homeowners to tailor the look of their fireplace to match their personal style and existing decor.

The technologies integrated into the Regency P42-LP4 and P42-NG4 are notable. Both models come equipped with system safety features, ensuring peace of mind. Additionally, they support the use of a programmable remote control, making adjustments to the temperature and flame appearance effortless while allowing homeowners to maintain comfort with just a click.

Efficiency is another key characteristic. These gas fireplaces highlight energy efficiency, designed to maximize heat output while minimizing fuel consumption. They have received high-efficiency ratings, which may qualify users for rebates or incentives in many regions, aligning with the growing demand for eco-friendly home heating solutions.

Installation flexibility is another advantage, with options for direct vent systems allowing for installation in various orientations and settings. This ensures homeowners can enjoy an attractive fireplace without needing extensive renovations or structural changes.

In conclusion, the Regency P42-LP4 and P42-NG4 are standout choices for anyone seeking a powerful, efficient, and stylish gas fireplace. With their innovative technologies, customizable features, and remarkable heating capabilities, these models offer an ideal focal point and cozy environment for any living space. They embody the perfect blend of modern design and traditional warmth, making them an excellent investment for enhancing home comfort and elegance.
Top Page Image Contents