Integra DTR-7.2 Rear panel facilities, Ir In/Out, Video In/Out, Multi Channel Input, S video jack

Page 15

IR IN/OUT

Rear panel facilities

IR IN/OUT

If the DTR-7.2 is located inside a rack or cabinet that will not allow infrared beams to reach the IR sensor, you will need to connect a remote sensor to IR IN input to be able to use the remote controller. Then install the remote sensor in an unblocked location where you can easily point the remote controller.

Using a mini-jack connector, connect the IR emitter to the IR OUT terminal on the DTR-7.2 and then place the IR emitter on the remote sensor of the component or facing it.

RS 232

The RS 232 port is to be used in conjunction with an external controller to control the operation of the DTR-7.2 by using an external device.

VIDEO IN/OUT

These are the video inputs and outputs. On the rear panel, there are five video inputs and two video outputs and each one includes both composite video and S video configurations. Connect VCRs, LD players, DVD players, and other video components to the video inputs.

The two video output channels can be used to be connected to video tape recorders for making recordings.

•When connecting a VCR or other video component, make sure you connect the audio and video leads together (i.e., both to VIDEO 3).

•The Video 5 inputs are located on the front panel.

Composite video jack

S video jack

MULTI CHANNEL INPUT

By connecting a DVD player, MPEG decoder, or other component that has a multi channel port, you can playback the audio with 5.1- channel or 7.1-channel output. So be sure to prepare a cable that can properly connect the DTR-7.2 to the peripheral device. The signal input from SURR BACK R is output to the SURR BACK SPEAKER terminal.

L (white)

Front output

R (red)	DIGITAL	PRE OUT
R (red)	OUTPUT	R	L
		FRONT
Subwoofer	OPT
Subwoofer
		SUB	CENTER
		SUB
	DIGITAL
	INPUT

GND

Use this GND terminal for connecting the ground (or earth) wire if a turntable is connected. Refer to “Connecting a turntable” on page 16.

L (white)

Surround

R (red)

Ex: DVD-Audio player/

MPEG decoder

R (red)

Surround back

L (white)

Center

COAX	SURR
1
	SURR
	BACK
2
3	FRONT
3
OPT	SUB
1

SURR

2

SURR

BACK

3

R

DIGITAL

INPUT

GND

MULTI C INPUT

CENTER

L

15

Image 15

Contents Remote controller ContentsBefore using Setup and operationAVIS Important Safeguards1. Recording Copyright Precautions4. Power For U.S. models Note to CATV system installerContents Contents Audio/Video Features FeaturesSupplied accessories Amplifier FeaturesBefore using this unit Installing the remote controller batteriesUsing the remote controller Front panel facilities Front panelFront panel display Front panel facilities Front panel facilities Remote controllerRemote controller DIGITAL INPUT/OUTPUT coaxial and optical Rear panel facilitiesA-BUS Rear panel facilitiesPRE OUT COMPONENT VIDEO INPUT/OUTPUTRear panel facilities REMOTE CONTROLPower on/ready function Power off functionMULTI CHANNEL INPUT Rear panel facilitiesIR IN/OUT VIDEO IN/OUTConnecting your audio components ConnectionsConnecting your video components ConnectionsConnections 6. Connecting a video cassette recorder VIDEODigital output 9.Connecting a television monitor or projectorConnections MONITOR OUTConnecting speakers Ideal speaker configurationSpeaker placement Connecting speakers Assembling the AM loop antenna Connecting antennasConnecting the AM antenna cable Connecting the included antennasDirectional linkage Connecting antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaWhen using the ZONE 2 OUT terminals Connecting the remote zone Zone 2 speakersother component from connecting blockConnecting the power Button on DTR-7.2 Setup menusNavigating through the Setup menu Button on remote controllerSetup menus Basic MenuAdvanced Menu 0. Hardware Setup menu Hardware Setup1. Speaker Setup menu Speaker Setup1-2.Speaker Distance sub-menu Speaker Setup1-3.Level Calibration sub-menu Speaker Setupa. Bass Peak Level Limiter Speaker Setup1-4.Bass Peak Level Bass Peak Level Manager* sub-menu2. Input Setup menu Input Setup2-2.Multichannel Setup sub-menu Input Setupb. Component Video Input Setup2-3.Video Setup sub-menu a. Video2-4.Character Input sub-menu Input Setup2-5.Intelli Volume sub-menu a. Intelli VolumeAnalog/PCM Input Setup2-6.Listening Mode Preset sub-menu Input source signala. Analog/PCM Input Setup2-7.12V Trigger Setup sub-menu Input Setup3. Audio Adjust Setup menu Audio AdjustAudio Adjust 3-6.Mono Setup Audio Adjust3-8.Surround Setup Audio AdjustParameter Audio AdjustSetting 3-10. 3-11. 3-12. 3-134. Preference menu Preference4-4.OSD Position sub-menu Preference4-2.Headphones Level Setup sub-menu 4-3.OSD Setup sub-menuListening to Radio Broadcasts Tuning into a radio stationListening to a stereo radio station FM mode Erasing a preset radio station Listening to Radio BroadcastsPresetting a radio station Selecting a preset radio stationTemporarily turning off the sound Enjoying music or videos with the DTR-7.2Adjusting the bass and treble Listening with headphonesChanging the listening mode Enjoying music or videos with the DTR-7.2Enjoying music or videos with the DTR-7.2 Switching the displayAdjusting the brightness of the front display Using the sleep time remote controller onlyEnjoying music or videos with the DTR-7.2 Changing the audio modeEnjoying the multichannel output Playing music using the buttons on the DTR-7.2 Enjoying music in the remote zoneRecording a source 1.Press the CD input source buttonVideo Overview Using remote controllerControlling an Integra/Onkyo CD player Using remote controllerON STDBY Using remote controllerDVD MODE SETUP VOL MENU MUTING SUBTITLE Controlling an Integra/Onkyo DVD player1 to 9, 0, --/--- Numeric keys Using remote controllerControlling an Integra/Onkyo MD recorder SAT, CABLE, VCR, and TV MODE buttonsLearning a pre-programmingcode Learning a pre-programmingcodeSETTING No Learning a pre-programmingcodeSETTING No SETTING NoCABLE MODE Cable Mode Operating your programmed remote controllerDVD MODE DVD Player Mode SAT MODE Satellite Tuner ModeOperating your programmed remote controller VCR MODE VCR ModeTV MODE TV Mode Programming procedure Page ENTER Erasing the programmed command from one buttonENTER 3.Press and release the same button againWhat is a Macro function? Using a Macro functionUsing a Macro function Programming the Direct Macro functionRunning a Direct Macro function 2.Press the MODE MACRO button again Using a Macro functionErasing a macro from the MODE MACRO button MODE MACROUsing a Macro function All channels SpecificationsREMOTE CONTROLLER AMPLIFIER SECTIONFM/AM TUNER Troubleshooting guidePOWER SPEAKERSOTHER Troubleshooting guideREMOTE CONTROLLER VIDEO and AUDIOMemo Memo SN 29343210A Integra Division of ONKYO U.S.A. CORPORATIONIntegra Division of ONKYO CORPORATION Tel 072-831-8111Fax