Integra DTR-7.2 Troubleshooting guide, VIDEO and AUDIO, Remote Controller, Other

Page 73
Troubleshooting guide

Troubleshooting guide

VIDEO and AUDIO

Desired picture does not appear.

Improper connection.

Check the connection again. Insert the plugs and connectors completely.

No OSD Menu display.

Improper connection.

Check connections.

OSD Menu is displayed when monitor is connected to VIDEO or S VIDEO of MONITOR OUT.

Confirm connections (see page 19).

No sound, or sound of the selected source is not heard.

Input Setup menu settings are incorrect. Check settings (see page 34).

No picture appears on the TV screen (or monitor).

TV (or monitor) is not set to receive the output signals from the receiver.

Set the TV (or monitor) to the receiver input.

Video cable is not connected securely.

Check connections.

You have connected to the COMPONENT VIDEO connectors but the DTR-7.2 is not set properly.

Check the Video Setup submenu of the Input Setup menu (page 36).

REMOTE CONTROLLER

Front panel controls function but remote controller controls do not.

No batteries in remote controller.

Insert batteries.

Batteries have worn out.

Replace batteries.

Remote controller is not pointed at the remote sensor of the DTR-7.2.

Point the remote controller at the remote sensor of the DTR- 7.2.

Remote controller is too far from the DTR-7.2.

Operate the remote controller within 16 feet (5 meters).

Remote controller is functioning in a different mode

Press the RCVR MODE button.

OTHER

LATE NIGHT function cannot be used.

Playback source is not Dolby Digital encoded.

Check that the DOLBY DIGITAL indicator lights up on the display.

Re-EQ function cannot be used.

Listening mode is set to Theater-Dimensional, Direct, PL II Music, or Neo:6 Music.

See page 44.

Parameter cannot be set for Front Effect etc.

Parameter may not be able to be set depending on the listening mode.

See table on page 45.

Multichannel audio is not output.

To listen to multichannel audio, “Yes” must be selected in the “Multichannel” in the Multichannel setup sub-menu of the Input Setup menu. Also, it is necessary to select Multichannel with the Audio Selector button.

Check that the component is connected to the MULTI CHANNEL INPUT port and check the Setup menu settings.

Components in remote zone (Zone 2) do not operate properly.

Components are incorrectly connected.

Check connections.

Objects are interfering with remote controller signals.

Move inferring objects away from path of remote controller signals.

If one of the messages shown below appears

“Not available with headphones use”

The operation is not allowed because headphones are plugged into the DTR-7.2.

“Not available with Multichannel use”

Cannot be used while the multi-channel output is being used.

“Not available in this Sp Config”

Will not work with the current speaker configuration settings.

“Not available in Zone 2 mode”

The operation is not allowed because the Zone 2 mode is turned on.

“Only available with Dolby D”

No setting other than Dolby Digital can be set.

“Not available in this Listening mode”

Will not work with the current listening mode.

“Not available with this signal”

The listening mode cannot be selected with the current input source.

“Not available with Muting”

Will not work because the muting is activated.

“Zone 2 is not On”

Will not work because the Zone 2 has not been turned on.

Also refer to the respective instruction manuals of the compact disc player, DVD player, video cassette recorder, TV monitor, etc., that compose your entertainment system.

The DTR-7.2 contains an internal microcomputer that performs high-level operations. However, on extremely rare occasions, noise or interference from an external source or static electricity may cause faulty operation. If this occurs, unplug the power cord from the wall outlet, wait five or more seconds, and then plug it back in. This should correct the situation.

*To reset the surround mode and other settings to the factory default settings, hold down the Video 1 button with the DTR-7.2 turned on and then press the Standby/On button. “CLEAR” appears in the front display and the DTR-7.2 enters the standby state.

73

Image 73
Contents Before using ContentsSetup and operation Remote controllerAVIS Important Safeguards4. Power PrecautionsFor U.S. models Note to CATV system installer 1. Recording CopyrightContents Contents Supplied accessories FeaturesAmplifier Features Audio/Video FeaturesInstalling the remote controller batteries Before using this unitUsing the remote controller Front panel Front panel facilitiesFront panel display Front panel facilities Front panel facilities Remote controllerRemote controller DIGITAL INPUT/OUTPUT coaxial and optical Rear panel facilitiesPRE OUT Rear panel facilitiesCOMPONENT VIDEO INPUT/OUTPUT A-BUSPower on/ready function REMOTE CONTROLPower off function Rear panel facilitiesIR IN/OUT Rear panel facilitiesVIDEO IN/OUT MULTI CHANNEL INPUTConnecting your audio components ConnectionsConnecting your video components ConnectionsConnections 6. Connecting a video cassette recorder VIDEOConnections 9.Connecting a television monitor or projectorMONITOR OUT Digital outputIdeal speaker configuration Connecting speakersSpeaker placement Connecting speakers Connecting the AM antenna cable Connecting antennasConnecting the included antennas Assembling the AM loop antennaConnecting an FM outdoor antenna Connecting antennasConnecting an AM outdoor antenna Directional linkageWhen using the ZONE 2 OUT terminals Connecting the remote zone Zone 2 speakersother component from connecting blockConnecting the power Navigating through the Setup menu Setup menusButton on remote controller Button on DTR-7.2Basic Menu Setup menusAdvanced Menu 0. Hardware Setup menu Hardware Setup1. Speaker Setup menu Speaker Setup1-2.Speaker Distance sub-menu Speaker Setup1-3.Level Calibration sub-menu Speaker Setup1-4.Bass Peak Level Speaker SetupBass Peak Level Manager* sub-menu a. Bass Peak Level Limiter2. Input Setup menu Input Setup2-2.Multichannel Setup sub-menu Input Setup2-3.Video Setup sub-menu Input Setupa. Video b. Component Video2-5.Intelli Volume sub-menu Input Setupa. Intelli Volume 2-4.Character Input sub-menu2-6.Listening Mode Preset sub-menu Input SetupInput source signal Analog/PCMa. Analog/PCM Input Setup2-7.12V Trigger Setup sub-menu Input Setup3. Audio Adjust Setup menu Audio AdjustAudio Adjust 3-6.Mono Setup Audio Adjust3-8.Surround Setup Audio AdjustSetting Audio Adjust3-10. 3-11. 3-12. 3-13 Parameter4. Preference menu Preference4-2.Headphones Level Setup sub-menu Preference4-3.OSD Setup sub-menu 4-4.OSD Position sub-menuTuning into a radio station Listening to Radio BroadcastsListening to a stereo radio station FM mode Presetting a radio station Listening to Radio BroadcastsSelecting a preset radio station Erasing a preset radio stationAdjusting the bass and treble Enjoying music or videos with the DTR-7.2Listening with headphones Temporarily turning off the soundChanging the listening mode Enjoying music or videos with the DTR-7.2Adjusting the brightness of the front display Switching the displayUsing the sleep time remote controller only Enjoying music or videos with the DTR-7.2Changing the audio mode Enjoying music or videos with the DTR-7.2Enjoying the multichannel output Playing music using the buttons on the DTR-7.2 Enjoying music in the remote zone1.Press the CD input source button Recording a sourceVideo Overview Using remote controllerControlling an Integra/Onkyo CD player Using remote controllerDVD MODE SETUP VOL MENU MUTING SUBTITLE Using remote controllerControlling an Integra/Onkyo DVD player ON STDBYControlling an Integra/Onkyo MD recorder Using remote controllerSAT, CABLE, VCR, and TV MODE buttons 1 to 9, 0, --/--- Numeric keysLearning a pre-programmingcode Learning a pre-programmingcodeSETTING No Learning a pre-programmingcodeSETTING No SETTING NoDVD MODE DVD Player Mode Operating your programmed remote controllerSAT MODE Satellite Tuner Mode CABLE MODE Cable ModeVCR MODE VCR Mode Operating your programmed remote controllerTV MODE TV Mode Programming procedure Page ENTER Erasing the programmed command from one button3.Press and release the same button again ENTERWhat is a Macro function? Using a Macro functionProgramming the Direct Macro function Using a Macro functionRunning a Direct Macro function Erasing a macro from the MODE MACRO button Using a Macro functionMODE MACRO 2.Press the MODE MACRO button againUsing a Macro function REMOTE CONTROLLER SpecificationsAMPLIFIER SECTION All channelsPOWER Troubleshooting guideSPEAKERS FM/AM TUNERREMOTE CONTROLLER Troubleshooting guideVIDEO and AUDIO OTHERMemo Memo Integra Division of ONKYO CORPORATION Integra Division of ONKYO U.S.A. CORPORATIONTel 072-831-8111Fax SN 29343210A