Integra DTR-7.2 Connecting the remote zone Zone 2 speakers, When using the ZONE 2 OUT terminals

Page 24

Connecting the remote zone (Zone 2) speakers

Connecting the remote zone (Zone 2) speakers

The DTR-7.2 allows you to connect another set of speakers and place them in a different room or separated area for listening to music. This other room or area is referred to as the remote zone (Zone 2), while the room where the DTR-7.2 is located is the main zone. In addition, the IR IN/OUT allows you to control the DTR-

7.2from the remote zone (Zone 2) with the remote controller even though the remote zone is physically separated. The diagram below shows how to make the proper connections for the remote zone.

When using the ZONE 2 OUT terminals

The ZONE 2 OUT terminal is a constant output. Connect to the LINE input of the amplifier (CD, tape, etc.). Adjust the volume with the amplifier connected to the ZONE 2 OUT terminal.

1.Connect the DTR-7.2 to the amplifier for the remote zone.

2.Connect the remote zone speaker cables to the speaker terminals on the amplifier.

Adjust the volume level at the amplifier.

3.Connect the DTR-7.2 to the monitor for the remote zone.

Remote Zone (Zone 2)
Zone 2			Zone 2 monitor				Zone 2
Left speaker			or projector			Right speaker

Zone 2 amplifier
			Main Room
	AUDIO	VIDEO	S VIDEO
			MONITOR
			OUT
R	L
	OUT		ZONE 2
Right (red)
			DTR-7.2
Left (white)

24

Image 24

Contents Contents Before usingSetup and operation Remote controllerImportant Safeguards AVISPrecautions 4. PowerFor U.S. models Note to CATV system installer 1. Recording CopyrightContents Contents Features Supplied accessoriesAmplifier Features Audio/Video FeaturesBefore using this unit Installing the remote controller batteriesUsing the remote controller Front panel facilities Front panelFront panel display Front panel facilities Remote controller Front panel facilitiesRemote controller Rear panel facilities DIGITAL INPUT/OUTPUT coaxial and opticalRear panel facilities PRE OUTCOMPONENT VIDEO INPUT/OUTPUT A-BUSREMOTE CONTROL Power on/ready functionPower off function Rear panel facilitiesRear panel facilities IR IN/OUTVIDEO IN/OUT MULTI CHANNEL INPUTConnections Connecting your audio componentsConnections Connecting your video components6. Connecting a video cassette recorder VIDEO Connections9.Connecting a television monitor or projector ConnectionsMONITOR OUT Digital outputConnecting speakers Ideal speaker configurationSpeaker placement Connecting speakers Connecting antennas Connecting the AM antenna cableConnecting the included antennas Assembling the AM loop antennaConnecting antennas Connecting an FM outdoor antennaConnecting an AM outdoor antenna Directional linkageConnecting the remote zone Zone 2 speakers When using the ZONE 2 OUT terminalsfrom connecting block other componentConnecting the power Setup menus Navigating through the Setup menuButton on remote controller Button on DTR-7.2Setup menus Basic MenuAdvanced Menu Hardware Setup 0. Hardware Setup menuSpeaker Setup 1. Speaker Setup menuSpeaker Setup 1-2.Speaker Distance sub-menuSpeaker Setup 1-3.Level Calibration sub-menuSpeaker Setup 1-4.Bass Peak LevelBass Peak Level Manager* sub-menu a. Bass Peak Level LimiterInput Setup 2. Input Setup menuInput Setup 2-2.Multichannel Setup sub-menuInput Setup 2-3.Video Setup sub-menua. Video b. Component VideoInput Setup 2-5.Intelli Volume sub-menua. Intelli Volume 2-4.Character Input sub-menuInput Setup 2-6.Listening Mode Preset sub-menuInput source signal Analog/PCMInput Setup a. Analog/PCMInput Setup 2-7.12V Trigger Setup sub-menuAudio Adjust 3. Audio Adjust Setup menuAudio Adjust Audio Adjust 3-6.Mono SetupAudio Adjust 3-8.Surround SetupAudio Adjust Setting3-10. 3-11. 3-12. 3-13 ParameterPreference 4. Preference menuPreference 4-2.Headphones Level Setup sub-menu4-3.OSD Setup sub-menu 4-4.OSD Position sub-menuListening to Radio Broadcasts Tuning into a radio stationListening to a stereo radio station FM mode Listening to Radio Broadcasts Presetting a radio stationSelecting a preset radio station Erasing a preset radio stationEnjoying music or videos with the DTR-7.2 Adjusting the bass and trebleListening with headphones Temporarily turning off the soundEnjoying music or videos with the DTR-7.2 Changing the listening modeSwitching the display Adjusting the brightness of the front displayUsing the sleep time remote controller only Enjoying music or videos with the DTR-7.2Enjoying music or videos with the DTR-7.2 Changing the audio modeEnjoying the multichannel output Enjoying music in the remote zone Playing music using the buttons on the DTR-7.2Recording a source 1.Press the CD input source buttonVideo Using remote controller OverviewUsing remote controller Controlling an Integra/Onkyo CD playerUsing remote controller DVD MODE SETUP VOL MENU MUTING SUBTITLEControlling an Integra/Onkyo DVD player ON STDBYUsing remote controller Controlling an Integra/Onkyo MD recorderSAT, CABLE, VCR, and TV MODE buttons 1 to 9, 0, --/--- Numeric keysLearning a pre-programmingcode Learning a pre-programmingcodeLearning a pre-programmingcode SETTING NoSETTING No SETTING NoOperating your programmed remote controller DVD MODE DVD Player ModeSAT MODE Satellite Tuner Mode CABLE MODE Cable ModeOperating your programmed remote controller VCR MODE VCR ModeTV MODE TV Mode Programming procedure Page Erasing the programmed command from one button ENTER3.Press and release the same button again ENTERUsing a Macro function What is a Macro function?Using a Macro function Programming the Direct Macro functionRunning a Direct Macro function Using a Macro function Erasing a macro from the MODE MACRO buttonMODE MACRO 2.Press the MODE MACRO button againUsing a Macro function Specifications REMOTE CONTROLLERAMPLIFIER SECTION All channelsTroubleshooting guide POWERSPEAKERS FM/AM TUNERTroubleshooting guide REMOTE CONTROLLERVIDEO and AUDIO OTHERMemo Memo Integra Division of ONKYO U.S.A. CORPORATION Integra Division of ONKYO CORPORATIONTel 072-831-8111Fax SN 29343210A