Integra DTR-7.2 instruction manual Erasing the programmed command from one button, Enter

Page 66
Erasing the programmed command from one button

Programming the commands of remote controllers for other devices into the remote controller

SEND/LEARN indicator

MODE buttons

3.Press and release the same button again.2.Press and release the same MODE button again.Manual background ENTER

HOME THEATER CONTROLLER

RC-461M

Erasing the programmed command from one button

You can only erase memorized commands and not preset ones.

1.Press and hold down the desired MODE button for the command, press the ENTER button, and then release both buttons.

When you press the MODE button, the SEND/LEARN indicator lights. When you press the ENTER button, the lamp turns off. When you release the buttons, the lamp lights again.

2.Press and release the button for the command you wish to erase.

When you press the button, the SEND/LEARN indicator turns off. When you release the button, the lamp lights again.

3.Press and release the same button again.

The SEND/LEARN lamp flashes twice slowly. The memorized command is erased.

Note:

If no button is pressed for more than 30 seconds during the erasing procedure, the SEND/LEARN indicator flashes three times quickly, and the remote controller exits the erasing mode. Resume from Step 1.

SEND/LEARN indicator

Manual backgroundManual background MODE Manual background buttons

Manual backgroundManual backgroundManual background ENTER

HOME THEATER CONTROLLER

RC-461M

Erasing all the commands programmed under a MODE button

1.Press and hold down the desired MODE button, press the ENTER button twice, and then release both buttons.

When you press the MODE button, the SEND/LEARN indicator lights. When you press the ENTER button, the lamp turns off. When you release the buttons, the lamp flashes twice slowly and then lights again.

2.Press and release the same MODE button again.

When you release the button, the SEND/LEARN indicator flashes twice slowly. This erases all the commands memorized to the MODE button.

Notes:

If no button is pressed for more than 30 seconds during the erasing procedure, the SEND/LEARN indicator flashes three times quickly and the remote controller exits the erasing mode. Resume from Step 1.

If you perform an invalid operation during erasing, the SEND/ LEARN indicator flashes three times quickly, and the remote controller exits the erasing mode. Resume from Step 1.

If many commands have been programmed to the MODE button, then the SEND/LEARN indicator may remain lit for up to 20 seconds during Step 2. This is not a malfunction.

66

Image 66
Contents Setup and operation ContentsBefore using Remote controllerImportant Safeguards AVISFor U.S. models Note to CATV system installer Precautions4. Power 1. Recording CopyrightContents Contents Amplifier Features FeaturesSupplied accessories Audio/Video FeaturesBefore using this unit Installing the remote controller batteriesUsing the remote controller Front panel facilities Front panelFront panel display Front panel facilities Remote controller Front panel facilitiesRemote controller Rear panel facilities DIGITAL INPUT/OUTPUT coaxial and opticalCOMPONENT VIDEO INPUT/OUTPUT Rear panel facilitiesPRE OUT A-BUSPower off function REMOTE CONTROLPower on/ready function Rear panel facilitiesVIDEO IN/OUT Rear panel facilitiesIR IN/OUT MULTI CHANNEL INPUTConnections Connecting your audio componentsConnections Connecting your video components6. Connecting a video cassette recorder VIDEO ConnectionsMONITOR OUT 9.Connecting a television monitor or projectorConnections Digital outputConnecting speakers Ideal speaker configurationSpeaker placement Connecting speakers Connecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an AM outdoor antenna Connecting antennasConnecting an FM outdoor antenna Directional linkageConnecting the remote zone Zone 2 speakers When using the ZONE 2 OUT terminalsfrom connecting block other componentConnecting the power Button on remote controller Setup menusNavigating through the Setup menu Button on DTR-7.2Setup menus Basic MenuAdvanced Menu Hardware Setup 0. Hardware Setup menuSpeaker Setup 1. Speaker Setup menuSpeaker Setup 1-2.Speaker Distance sub-menuSpeaker Setup 1-3.Level Calibration sub-menuBass Peak Level Manager* sub-menu Speaker Setup1-4.Bass Peak Level a. Bass Peak Level LimiterInput Setup 2. Input Setup menuInput Setup 2-2.Multichannel Setup sub-menua. Video Input Setup2-3.Video Setup sub-menu b. Component Videoa. Intelli Volume Input Setup2-5.Intelli Volume sub-menu 2-4.Character Input sub-menuInput source signal Input Setup2-6.Listening Mode Preset sub-menu Analog/PCMInput Setup a. Analog/PCMInput Setup 2-7.12V Trigger Setup sub-menuAudio Adjust 3. Audio Adjust Setup menuAudio Adjust Audio Adjust 3-6.Mono SetupAudio Adjust 3-8.Surround Setup3-10. 3-11. 3-12. 3-13 Audio AdjustSetting ParameterPreference 4. Preference menu4-3.OSD Setup sub-menu Preference4-2.Headphones Level Setup sub-menu 4-4.OSD Position sub-menuListening to Radio Broadcasts Tuning into a radio stationListening to a stereo radio station FM mode Selecting a preset radio station Listening to Radio BroadcastsPresetting a radio station Erasing a preset radio stationListening with headphones Enjoying music or videos with the DTR-7.2Adjusting the bass and treble Temporarily turning off the soundEnjoying music or videos with the DTR-7.2 Changing the listening modeUsing the sleep time remote controller only Switching the displayAdjusting the brightness of the front display Enjoying music or videos with the DTR-7.2Enjoying music or videos with the DTR-7.2 Changing the audio modeEnjoying the multichannel output Enjoying music in the remote zone Playing music using the buttons on the DTR-7.2Recording a source 1.Press the CD input source buttonVideo Using remote controller OverviewUsing remote controller Controlling an Integra/Onkyo CD playerControlling an Integra/Onkyo DVD player Using remote controllerDVD MODE SETUP VOL MENU MUTING SUBTITLE ON STDBYSAT, CABLE, VCR, and TV MODE buttons Using remote controllerControlling an Integra/Onkyo MD recorder 1 to 9, 0, --/--- Numeric keysLearning a pre-programmingcode Learning a pre-programmingcodeSETTING No Learning a pre-programmingcodeSETTING No SETTING NoSAT MODE Satellite Tuner Mode Operating your programmed remote controllerDVD MODE DVD Player Mode CABLE MODE Cable ModeOperating your programmed remote controller VCR MODE VCR ModeTV MODE TV Mode Programming procedure Page 3.Press and release the same button again Erasing the programmed command from one buttonENTER ENTERUsing a Macro function What is a Macro function?Using a Macro function Programming the Direct Macro functionRunning a Direct Macro function MODE MACRO Using a Macro functionErasing a macro from the MODE MACRO button 2.Press the MODE MACRO button againUsing a Macro function AMPLIFIER SECTION SpecificationsREMOTE CONTROLLER All channelsSPEAKERS Troubleshooting guidePOWER FM/AM TUNERVIDEO and AUDIO Troubleshooting guideREMOTE CONTROLLER OTHERMemo Memo Tel 072-831-8111Fax Integra Division of ONKYO U.S.A. CORPORATIONIntegra Division of ONKYO CORPORATION SN 29343210A