Integra Understanding LPF for LFE and Subwoofer LFE Input Settings
Page 67

DTR-7.6,6.6.book Page 67 Monday, September 26, 2005 1:40 PM

Advanced Setup—Continued

7

8

9

Use the Up and Down []/[ ] buttons to select “d. Surround,” and then use the Left and Right []/[ ] buttons to select a crossover frequency.

If no surround left and right speakers are connected, select None.

Note:

•If the Front setting in step 5 is set to anything other than Full Band, Full Band cannot be selected here.

Use the Up and Down []/[ ] buttons to select “e. SurrBack,” and then use the Left and Right []/[ ] buttons to select a crossover frequency.

If no surround back speakers are con- nected, select None.

Notes:

•If the Surround setting in step 7 is set to None, this setting cannot be selected.

•If the Surround setting in step 7 is set to anything other than Full Band, Full Band cannot be selected here.

Use the Up and Down []/[ ] buttons to select “f. SurrBack Ch,” and then use the Left and Right []/[ ] buttons to select:

1ch: Select if one surround back

speaker is connected.

2ch: Select if two (left and right) surround back speakers are connected.

Continue with step 10 in the next col- umn.

Low-Pass Filter for the LFE Channel

This setting is not set automatically by the Automatic Speaker Setup function (see page 38).

With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

*If you are using THX-certified speakers, select 80 Hz (THX).

10 Use the Up and Down []/[ ] buttons to select “g.LPF of LFE,” and then use the Left and Right []/[ ] buttons to select a low- pass filter frequency.

The following low-pass filter frequen- cies can be selected: 80 Hz (THX) (default), 90 Hz, 100 Hz, 110 Hz, or 120 Hz.

Continue with step 11 below.

Subwoofer Mode

This setting is not set automatically by the Automatic Speaker Setup function (see page 38).

With this setting, you can boost bass output by feeding front left and right channel bass sounds to the subwoofer. This setting can only be made if the Subwoofer setting in step 4 is set to Yes, and the Front setting in step 5 is set to Full Band.

*If you are using THX-certified speakers, select LFE only (THX).

11 Use the Up and Down []/[ ] buttons to select “h. Subwoofer Mode,” and then use the Left and Right []/[ ] buttons to select:

LFE only (THX): The subwoofer only outputs the LFE channel.

Double Bass: In addition to LFE chan- nel sounds, the subwoofer outputs front left and right channel bass sounds.

12

Press the [Setup] button.

 

 

Setup closes.

Note:

•These procedures can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button.

67

Page 66 Page 68
Image 67
Page 66 Page 68
Contents DTR-7.6/6.6 Avis Important Safety InstructionsPower PrecautionsMake sure you have the following accessories Supplied AccessoriesContents DTR-6.6 Only FeaturesDTR-7.6 and DTR-6.6 DTR-7.6 OnlyInstalling the Batteries Before Using the AV receiverUsing the Remote Controller Front Panel Getting to Know the AV ReceiverDisplay Getting to Know the AV ReceiverDTR-7.6 Rear PanelDTR-6.6 Video 1 IN/OUT and Video 2 IN/OUT Component Video in 1, 2,Hdmi in 1, 2, and OUT DTR-7.6 only XM antenna on North American modelAbout the Remote Controller Modes Remote ControllerReceiver/Tape Mode Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Enjoying Home Theater Connecting Your SpeakersConnecting Your Speakers Connecting Your SpeakersStrip about 5/8 Speaker Connection PrecautionsConnecting the Speaker Cables Read the following before connecting your speakersAttach the FM antenna, as shown American Model Connecting AntennaConnecting the AM Loop Antenna Connecting the Indoor FM AntennaUsing a TV/FM Antenna Splitter Connecting AntennaConnecting an Outdoor FM Antenna Connecting an Outdoor AM AntennaAV Connection Color Coding Connecting Your ComponentsAbout AV Connections Optical Digital JacksVideo Connection Formats Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Which Connections Should I Use?Hint Connecting a TV or ProjectorVideo Connection Audio ConnectionConnecting a DVD player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device Connecting a Turntable Connecting a CD PlayerStep Connecting a Power Amplifier Connecting a Cassette, CDR, MiniDisc, or DAT RecorderAuto Power On/Standby Connecting ComponentsAbout Copyright Protection Connecting Components with Hdmi DTR-7.6 OnlyAbout Hdmi Supported Audio FormatsMaking Hdmi Connections Standby indicator lights up Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Connecting the Power CordSmooth Operation in a Few Easy Steps Do the automatic speaker setup-this is essentialTurning On the AV Receiver Turning On and StandbyConnected TV Put the speaker setup microPhone in the listening position Turn on the AV receiverOn completion, the following menu appears First Time SetupDisconnect the speaker setup Press EnterChecking the Results Hdmi Video menu appears Hdmi Video Setup DTR-7.6 OnlyPress the Setup button Setup closesComponent Video menu appears Component Video SetupLowed by the Setup button Press the Receiver button, folDigital Input menu appears Digital Audio Input SetupSetup closes DTR-7.6 onlyChanging the Input Display Minimum Speaker Impedance Buttons to select 8. Hardware TV Format Setup Not North American modelsAM Frequency Step Setup on some models Use the Up and DownStart playback on the source component Select a listening mode and enjoyPlaying Your AV Components Basic AV Receiver OperationDisplaying AM/FM Radio Information Tuning into AM/FM Radio StationsListening to the Radio Listening to AM/FM StationsListening to the Radio Connecting the XM AntennaSigning Up for XM Satellite Radio Use the Up and Down Buttons to select a channel Channel Search modeMode button, followed by Selecting XM Radio ChannelsNel Displaying XM Radio InformationSelecting XM Channels from the Front Panel Buttons to select a chanXM Radio Messages Positioning the XM AntennaXM Channels Presetting AM/FM StationsSelecting Presets Deleting PresetsInput Channel Using the Multichannel DVD InputUsing the Multichannel DVD Input Multichannel DVD Input SettingsMuting the AV Receiver Adjusting Speaker LevelsSetting the Display Brightness Common FunctionsDisplaying Source Information Using the Sleep TimerUsing Headphones Common FunctionsSelecting on the AV Receiver Using the Listening ModesSelecting with the Remote Controller Selecting the Listening ModesDVD Using the Listening ModesSound is output by the front left and right speakers Use this mode with any stereo or TV, DVD, VHSUse this mode with any stereo movie e.g., TV, DVD, VHS About the Listening ModesOnkyo Original DSP Modes This mode is designed for use with video gamesRecording Audio and Video from Separate Sources RecordingRecording the Input Source About the Onscreen Setup Menus Onscreen Setup MenusAudio Adjust Menu Adjusting the Listening ModesUsing the Re-EQ Function Neo6 Music Adjusting the Listening ModesTone Control Settings PL IIx and Neo6 Settings PL IIx Music 2 ch onlyMultiplex Dolby Digital SettingsMono/Multiplex Settings LFE Level SettingOptions for that input selector Appear Default Listening ModesListening Mode Preset menu Appears Use the Up and Down Buttons to select 5. ListeningSpeaker Config menu appears Advanced SetupSpeaker Setup Speaker Setup menu appearsLFE only THX The subwoofer only outputs the LFE channel Advanced SetupSubwoofer Mode Low-Pass Filter for the LFE ChannelRepeat for all speakers Speaker DistanceButtons to select Speaker Dis Tance, and then press EnterSpeaker Level Calibration Back speaker spacing THX Audio SetupSetup menu closes Buttons to specify the surroundTings option to Equalizer SettingsRepeat steps 6 and 7 for each speaker Buttons to set the a. Use SetDelay Input SetupUse the arrow Character EditThen press Enter Repeat to enter up to Characters Volume Setup IntelliVolumePreferences OSD Position OSD SetupHdmi Setup DTR-7.6 Only Lock SetupRemote IDs Changing the Remote Controller’s IDChanging the AV Receiver’s Remote ID Opt, coax, or HDMI, and then Digital Input Signal FormatsInput, and then press Enter Use the Up and Down That’s assigned to a digital inputZone Connecting ZoneUsing Another Amp in Zone Using Only Speakers in ZoneZone 2 Out Setting Powered Zone 2 SettingUsing Zone Ton, and then use the Level On the remote controller, pressZone 2 Remote Mode but To adjust12V Trigger Setting for Each Input Source Using the 12V Triggers in Zone 2 and the Main RoomRepeat this step as necessary for each setting DelayUsing a Multiroom Kit with Zone Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Other Components Controlling Other Components Entering Remote Control CodesControlling Other Components Resetting the Remote ControllerRemote Control Codes for Integra Components Connected via Resetting the Remote Mode ButtonsTV Input On, Standby, TVCH +/-, TV CH + Prev CHLearning Commands from Other Remote Controllers Deleting Macros Using MacrosMaking Macros Running MacrosTroubleshooting Troubleshooting Immediate display does not appear Remote controller doesn’t workCan’t learn commands from another remote controller Sound changes when I connect my head- phonesDTR-7.6,6.6.book Page 92 Monday, September 26, 2005 140 PM Tuner Section SpecificationAmplifier Section Video SectionMemo DTR-7.6,6.6.book Page 95 Monday, September 26, 2005 140 PM 3 4 4 0 8

DTR-7.6/6.6 specifications

The Integra DTR-7.6 and DTR-6.6 are high-performance AV receivers that cater to audiophiles and home theater enthusiasts alike. Both models are designed to deliver exceptional audio quality and advanced features, making them ideal for a wide range of entertainment needs.

One of the standout characteristics of the DTR-7.6 and DTR-6.6 is their ability to support advanced audio formats, including Dolby Atmos and DTS:X. This enables users to experience immersive soundscapes by harnessing overhead sound for a three-dimensional auditory experience. The receivers also feature multiple speaker configuration options, allowing you to set up a customized surround sound experience based on your room’s size and shape.

In terms of power output, the DTR-7.6 offers an impressive power rating, providing ample drive for even the most demanding speaker systems. The DTR-6.6, while having a slightly lower power output, still boasts sufficient capabilities for medium to large home theater setups. Both models incorporate high-current amplifiers, ensuring clean and dynamic performance across all frequencies.

The inclusion of advanced video processing technologies further enhances the viewing experience. With support for 4K UHD video and HDR formats such as HDR10, Dolby Vision, and HLG, users can expect stunning picture quality and vibrant color reproduction. The receivers come equipped with multiple HDMI inputs, enabling users to connect various devices such as gaming consoles, Blu-ray players, and streaming devices effortlessly.

Connectivity options on both the DTR-7.6 and DTR-6.6 are extensive, featuring built-in Wi-Fi and Bluetooth for easy streaming from smartphones and tablets. Additionally, the receivers support popular streaming services, making it simple to access a vast library of music and entertainment. For those who value a seamless setup process, both models also support automated calibration through Audyssey MultEQ, which fine-tunes your system based on the unique acoustics of your space.

The sleek design of both receivers ensures they will fit well within any entertainment setup. The front panel includes an easy-to-navigate interface with a clear display, remote control functionality, and compatibility with smart home systems. Overall, the DTR-7.6 and DTR-6.6 are powerful, feature-rich receivers that stand out in the crowded AV market, offering a combination of advanced technologies and audio performance suitable for both casual listeners and serious audiophiles.
Top Page Image Contents