Integra DTR-7.6/6.6 Advanced Setup, Speaker Setup menu appears, Speaker Config menu appears

Page 66

DTR-7.6,6.6.book Page 66 Monday, September 26, 2005 1:40 PM

Advanced Setup

Speaker Setup

2

This section explains how to check the speaker settings and how to set them manually, which is useful if you change a speaker after performing the automatic speaker setup.

Some speaker settings are set automatically by the Auto- matic Speaker Setup function (see page 38).

Use the Up and Down []/[ ] buttons to select “3. Speaker Setup,” and then press [Enter].

The Speaker Setup menu appears.

Receiver

Enter

Speaker Configuration

3

Setup

4

Use the Up and Down []/[ ] buttons to select “Speaker Con- figuration,” and then press [Enter].

The Speaker Config menu appears.

3-2.Speaker Config

------------------------

a.Subwoofer

 

:Yes

b.Front

:80Hz(THX)

c.Center

:80Hz(THX)

d.Surround

:80Hz(THX)

e.SurrBack

:80Hz(THX)

f.SurrBack Ch

:2ch

g.LPF of LFE

 

 

:80Hz(THX)

h.Subwoofer Mode :-------------

Use the Up and Down []/[ ] buttons to select “a. Subwoofer,” and then use the Left and Right []/[ ] buttons to select:

These settings are set automatically by the Automatic Speaker Setup function (see page 38).

With these settings, you can specify which speakers are

connected and a crossover frequency for each speaker.

5

 

The following crossover frequencies can be specified:

 

Full Band, 40 Hz, 50 Hz, 60 Hz, 70 Hz, 80 Hz (THX),

 

90 Hz, 100 Hz, 110 Hz, 120 Hz, 130 Hz, 150 Hz,

 

200 Hz.

 

 

Specify Full Band for speakers that can output low-fre-

 

quency bass sounds adequately, for example, speakers

 

with a good sized woofer. For smaller speakers, specify

 

a crossover frequency. Sounds below the crossover fre-

6

quency will be output by the subwoofer instead of the

 

speaker. Refer to your speakers’ manuals to determine

 

the optimum crossover frequencies.

 

If you’re using THX-certified speakers, specify

 

80 Hz (THX) for all speakers.

 

 

 

 

1

Press the [Receiver] Remote

 

 

 

 

Mode button, followed by the

 

 

[Setup] button.

 

The main menu appears onscreen.

Yes: Select if a subwoofer is con- nected.

No: Select if no subwoofer is con- nected.

Use the Up and Down []/[ ] buttons to select “b. Front,” and then use the Left and Right

[]/[ ] buttons to select a crossover frequency.

Note:

•If the Subwoofer setting in step 4 is set to No, this is fixed at Full Band.

Use the Up and Down []/[ ] buttons to select “c. Center,” and then use the Left and Right

[]/[ ] buttons to select a crossover frequency.

If no center speaker is connected, select None.

Note:

•If the Front setting in step 5 is set to anything other than Full Band, Full Band cannot be selected here.

66

Page 65 Page 67
Image 66
Page 65 Page 67
Contents DTR-7.6/6.6 Important Safety Instructions AvisPrecautions PowerSupplied Accessories Make sure you have the following accessoriesContents DTR-7.6 Only FeaturesDTR-7.6 and DTR-6.6 DTR-6.6 OnlyBefore Using the AV receiver Installing the BatteriesUsing the Remote Controller Getting to Know the AV Receiver Front PanelGetting to Know the AV Receiver DisplayRear Panel DTR-7.6DTR-6.6 XM antenna on North American model Component Video in 1, 2,Hdmi in 1, 2, and OUT DTR-7.6 only Video 1 IN/OUT and Video 2 IN/OUTRemote Controller About the Remote Controller ModesReceiver/Tape Mode Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Connecting Your Speakers Enjoying Home TheaterConnecting Your Speakers Connecting Your SpeakersRead the following before connecting your speakers Speaker Connection PrecautionsConnecting the Speaker Cables Strip about 5/8Connecting the Indoor FM Antenna Connecting AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shown American ModelConnecting an Outdoor AM Antenna Connecting AntennaConnecting an Outdoor FM Antenna Using a TV/FM Antenna SplitterOptical Digital Jacks Connecting Your ComponentsAbout AV Connections AV Connection Color CodingWhich Connections Should I Use? Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Video Connection FormatsAudio Connection Connecting a TV or ProjectorVideo Connection HintConnecting a DVD player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device Connecting a CD Player Connecting a TurntableStep Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Connecting a Power AmplifierConnecting Components Auto Power On/StandbySupported Audio Formats Connecting Components with Hdmi DTR-7.6 OnlyAbout Hdmi About Copyright ProtectionMaking Hdmi Connections Connecting the Power Cord Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Standby indicator lights upTurning On and Standby Do the automatic speaker setup-this is essentialTurning On the AV Receiver Smooth Operation in a Few Easy StepsTurn on the AV receiver Put the speaker setup microPhone in the listening position Connected TVPress Enter First Time SetupDisconnect the speaker setup On completion, the following menu appearsChecking the Results Setup closes Hdmi Video Setup DTR-7.6 OnlyPress the Setup button Hdmi Video menu appearsPress the Receiver button, fol Component Video SetupLowed by the Setup button Component Video menu appearsDTR-7.6 only Digital Audio Input SetupSetup closes Digital Input menu appearsChanging the Input Display Minimum Speaker Impedance Use the Up and Down TV Format Setup Not North American modelsAM Frequency Step Setup on some models Buttons to select 8. HardwareBasic AV Receiver Operation Select a listening mode and enjoyPlaying Your AV Components Start playback on the source componentListening to AM/FM Stations Tuning into AM/FM Radio StationsListening to the Radio Displaying AM/FM Radio InformationConnecting the XM Antenna Listening to the RadioSigning Up for XM Satellite Radio Selecting XM Radio Channels Channel Search modeMode button, followed by Use the Up and Down Buttons to select a channelButtons to select a chan Displaying XM Radio InformationSelecting XM Channels from the Front Panel NelPositioning the XM Antenna XM Radio MessagesDeleting Presets Presetting AM/FM StationsSelecting Presets XM ChannelsMultichannel DVD Input Settings Using the Multichannel DVD InputUsing the Multichannel DVD Input Input ChannelCommon Functions Adjusting Speaker LevelsSetting the Display Brightness Muting the AV ReceiverCommon Functions Using the Sleep TimerUsing Headphones Displaying Source InformationSelecting the Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV ReceiverUsing the Listening Modes DVDAbout the Listening Modes Use this mode with any stereo or TV, DVD, VHSUse this mode with any stereo movie e.g., TV, DVD, VHS Sound is output by the front left and right speakersThis mode is designed for use with video games Onkyo Original DSP ModesRecording Recording Audio and Video from Separate SourcesRecording the Input Source Onscreen Setup Menus About the Onscreen Setup MenusAdjusting the Listening Modes Audio Adjust MenuUsing the Re-EQ Function PL IIx and Neo6 Settings PL IIx Music 2 ch only Adjusting the Listening ModesTone Control Settings Neo6 MusicLFE Level Setting Dolby Digital SettingsMono/Multiplex Settings MultiplexUse the Up and Down Buttons to select 5. Listening Default Listening ModesListening Mode Preset menu Appears Options for that input selector AppearSpeaker Setup menu appears Advanced SetupSpeaker Setup Speaker Config menu appearsLow-Pass Filter for the LFE Channel Advanced SetupSubwoofer Mode LFE only THX The subwoofer only outputs the LFE channelTance, and then press Enter Speaker DistanceButtons to select Speaker Dis Repeat for all speakersSpeaker Level Calibration Buttons to specify the surround THX Audio SetupSetup menu closes Back speaker spacingButtons to set the a. Use Set Equalizer SettingsRepeat steps 6 and 7 for each speaker Tings option toInput Setup DelayCharacter Edit Use the arrowThen press Enter Repeat to enter up to Characters IntelliVolume Volume SetupPreferences Lock Setup OSD SetupHdmi Setup DTR-7.6 Only OSD PositionChanging the Remote Controller’s ID Remote IDsChanging the AV Receiver’s Remote ID That’s assigned to a digital input Digital Input Signal FormatsInput, and then press Enter Use the Up and Down Opt, coax, or HDMI, and thenUsing Only Speakers in Zone Connecting ZoneUsing Another Amp in Zone ZonePowered Zone 2 Setting Zone 2 Out SettingUsing Zone To adjust On the remote controller, pressZone 2 Remote Mode but Ton, and then use the LevelDelay Using the 12V Triggers in Zone 2 and the Main RoomRepeat this step as necessary for each setting 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with a Cabinet Using a Multiroom Kit with ZoneUsing a Multiroom Kit with Other Components Entering Remote Control Codes Controlling Other ComponentsResetting the Remote Mode Buttons Resetting the Remote ControllerRemote Control Codes for Integra Components Connected via Controlling Other ComponentsPrev CH On, Standby, TVCH +/-, TV CH + TV InputLearning Commands from Other Remote Controllers Running Macros Using MacrosMaking Macros Deleting MacrosTroubleshooting Troubleshooting Sound changes when I connect my head- phones Remote controller doesn’t workCan’t learn commands from another remote controller Immediate display does not appearDTR-7.6,6.6.book Page 92 Monday, September 26, 2005 140 PM Video Section SpecificationAmplifier Section Tuner SectionMemo DTR-7.6,6.6.book Page 95 Monday, September 26, 2005 140 PM 3 4 4 0 8

DTR-7.6/6.6 specifications

The Integra DTR-7.6 and DTR-6.6 are high-performance AV receivers that cater to audiophiles and home theater enthusiasts alike. Both models are designed to deliver exceptional audio quality and advanced features, making them ideal for a wide range of entertainment needs.

One of the standout characteristics of the DTR-7.6 and DTR-6.6 is their ability to support advanced audio formats, including Dolby Atmos and DTS:X. This enables users to experience immersive soundscapes by harnessing overhead sound for a three-dimensional auditory experience. The receivers also feature multiple speaker configuration options, allowing you to set up a customized surround sound experience based on your room’s size and shape.

In terms of power output, the DTR-7.6 offers an impressive power rating, providing ample drive for even the most demanding speaker systems. The DTR-6.6, while having a slightly lower power output, still boasts sufficient capabilities for medium to large home theater setups. Both models incorporate high-current amplifiers, ensuring clean and dynamic performance across all frequencies.

The inclusion of advanced video processing technologies further enhances the viewing experience. With support for 4K UHD video and HDR formats such as HDR10, Dolby Vision, and HLG, users can expect stunning picture quality and vibrant color reproduction. The receivers come equipped with multiple HDMI inputs, enabling users to connect various devices such as gaming consoles, Blu-ray players, and streaming devices effortlessly.

Connectivity options on both the DTR-7.6 and DTR-6.6 are extensive, featuring built-in Wi-Fi and Bluetooth for easy streaming from smartphones and tablets. Additionally, the receivers support popular streaming services, making it simple to access a vast library of music and entertainment. For those who value a seamless setup process, both models also support automated calibration through Audyssey MultEQ, which fine-tunes your system based on the unique acoustics of your space.

The sleek design of both receivers ensures they will fit well within any entertainment setup. The front panel includes an easy-to-navigate interface with a clear display, remote control functionality, and compatibility with smart home systems. Overall, the DTR-7.6 and DTR-6.6 are powerful, feature-rich receivers that stand out in the crowded AV market, offering a combination of advanced technologies and audio performance suitable for both casual listeners and serious audiophiles.
Top Page Image Contents