Integra DTR-7.6/6.6 instruction manual Speaker Level Calibration, Speaker Setup menu appears

Page 69

DTR-7.6,6.6.book Page 69 Monday, September 26, 2005 1:40 PM

Advanced Setup—Continued

Speaker Level Calibration

3

These settings are set automatically by the Automatic

Speaker Setup function (see page 38).

With these settings, you can adjust the level of each speaker while listening to the test tone so that the volume of each speaker is the same at the listening position.

Notes:

• The speakers cannot be calibrated while the output of the AV receiver is muted or a pair of headphones is connected.

• Because the AV receiver supports THX, the test tone is output at the standard level of 0 dB (abso- lute volume setting 82). If you normally listen at volume settings below this, be careful because the test tone will be much louder.

1

Press the [Receiver] Remote

 

 

 

 

Mode button, followed by the

4

 

[Setup] button.

 

The main menu appears onscreen.

 

2

Use the Up and Down [ ]/[

]

 

buttons to select “3. Speaker

 

 

Setup,” and then press [Enter].

 

The Speaker Setup menu appears.

5

6

Use the Up and Down []/[ ] buttons to select “Level Calibra- tion,” and then press [Enter].

The Level Calibration menu appears and the pink noise test tone is output by the front left speaker.

3-4.Level Calibration

------------------------

a.Left

:

0dB

b.Center

:

0dB

c.Right

:

0dB

d.Surround R

:

0dB

e.SurrBack R

:

0dB

f.SurrBack L

:

0dB

g.Surround L

:

0dB

h.Subwoofer

:

0dB

Note:

Speakers that you set to No or None on the Speaker Config menu (page 66) cannot be adjusted.

Use the Up and Down []/[ ] buttons to select each speaker, and use the Left and Right

[ ]/[

] buttons to set the vol-

ume.

 

The level can be adjusted from –12 to +12 dB in 1 dB steps (–15 to +12 dB for the subwoofer).

Repeat step 4 so that the volume of the test tone from each speaker is the same.

If you’re using a handheld sound level meter, adjust the level of each speaker so it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading.

Press the [Setup] button.

Setup closes.

Note:

•The speaker levels can also be changed by using the dedicated buttons on the remote controller. Press the [Test Tone] button to output the test tone. Use the [CH Sel] button to select each speaker, and use the [Level–] and [Level+] buttons to adjust the level.

69

Page 68 Page 70
Image 69
Page 68 Page 70
Contents DTR-7.6/6.6 Avis Important Safety InstructionsPower PrecautionsMake sure you have the following accessories Supplied AccessoriesContents DTR-7.6 and DTR-6.6 FeaturesDTR-7.6 Only DTR-6.6 OnlyBefore Using the AV receiver Installing the BatteriesUsing the Remote Controller Front Panel Getting to Know the AV ReceiverDisplay Getting to Know the AV ReceiverRear Panel DTR-7.6DTR-6.6 Hdmi in 1, 2, and OUT DTR-7.6 only Component Video in 1, 2,XM antenna on North American model Video 1 IN/OUT and Video 2 IN/OUTRemote Controller About the Remote Controller ModesReceiver/Tape Mode Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Enjoying Home Theater Connecting Your SpeakersConnecting Your Speakers Connecting Your SpeakersConnecting the Speaker Cables Speaker Connection PrecautionsRead the following before connecting your speakers Strip about 5/8Connecting the AM Loop Antenna Connecting AntennaConnecting the Indoor FM Antenna Attach the FM antenna, as shown American ModelConnecting an Outdoor FM Antenna Connecting AntennaConnecting an Outdoor AM Antenna Using a TV/FM Antenna SplitterAbout AV Connections Connecting Your ComponentsOptical Digital Jacks AV Connection Color CodingConnecting Audio and Video Signals to the AV Receiver Connecting Your ComponentsWhich Connections Should I Use? Video Connection FormatsVideo Connection Connecting a TV or ProjectorAudio Connection HintConnecting a DVD player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device Connecting a CD Player Connecting a TurntableStep Connecting a Power Amplifier Connecting a Cassette, CDR, MiniDisc, or DAT RecorderAuto Power On/Standby Connecting ComponentsAbout Hdmi Connecting Components with Hdmi DTR-7.6 OnlySupported Audio Formats About Copyright ProtectionMaking Hdmi Connections Connecting the RS232 Port Connecting the Power Cords of Other ComponentsConnecting the Power Cord Standby indicator lights upTurning On the AV Receiver Do the automatic speaker setup-this is essentialTurning On and Standby Smooth Operation in a Few Easy StepsPhone in the listening position Put the speaker setup microTurn on the AV receiver Connected TVDisconnect the speaker setup First Time SetupPress Enter On completion, the following menu appearsChecking the Results Press the Setup button Hdmi Video Setup DTR-7.6 OnlySetup closes Hdmi Video menu appearsLowed by the Setup button Component Video SetupPress the Receiver button, fol Component Video menu appearsSetup closes Digital Audio Input SetupDTR-7.6 only Digital Input menu appearsChanging the Input Display Minimum Speaker Impedance AM Frequency Step Setup on some models TV Format Setup Not North American modelsUse the Up and Down Buttons to select 8. HardwarePlaying Your AV Components Select a listening mode and enjoyBasic AV Receiver Operation Start playback on the source componentListening to the Radio Tuning into AM/FM Radio StationsListening to AM/FM Stations Displaying AM/FM Radio InformationConnecting the XM Antenna Listening to the RadioSigning Up for XM Satellite Radio Mode button, followed by Channel Search modeSelecting XM Radio Channels Use the Up and Down Buttons to select a channelSelecting XM Channels from the Front Panel Displaying XM Radio InformationButtons to select a chan NelXM Radio Messages Positioning the XM AntennaSelecting Presets Presetting AM/FM StationsDeleting Presets XM ChannelsUsing the Multichannel DVD Input Using the Multichannel DVD InputMultichannel DVD Input Settings Input ChannelSetting the Display Brightness Adjusting Speaker LevelsCommon Functions Muting the AV ReceiverUsing Headphones Using the Sleep TimerCommon Functions Displaying Source InformationSelecting with the Remote Controller Using the Listening ModesSelecting the Listening Modes Selecting on the AV ReceiverDVD Using the Listening ModesUse this mode with any stereo movie e.g., TV, DVD, VHS Use this mode with any stereo or TV, DVD, VHSAbout the Listening Modes Sound is output by the front left and right speakersOnkyo Original DSP Modes This mode is designed for use with video gamesRecording Recording Audio and Video from Separate SourcesRecording the Input Source About the Onscreen Setup Menus Onscreen Setup MenusAdjusting the Listening Modes Audio Adjust MenuUsing the Re-EQ Function Tone Control Settings Adjusting the Listening ModesPL IIx and Neo6 Settings PL IIx Music 2 ch only Neo6 MusicMono/Multiplex Settings Dolby Digital SettingsLFE Level Setting MultiplexListening Mode Preset menu Appears Default Listening ModesUse the Up and Down Buttons to select 5. Listening Options for that input selector AppearSpeaker Setup Advanced SetupSpeaker Setup menu appears Speaker Config menu appearsSubwoofer Mode Advanced SetupLow-Pass Filter for the LFE Channel LFE only THX The subwoofer only outputs the LFE channelButtons to select Speaker Dis Speaker DistanceTance, and then press Enter Repeat for all speakersSpeaker Level Calibration Setup menu closes THX Audio SetupButtons to specify the surround Back speaker spacingRepeat steps 6 and 7 for each speaker Equalizer SettingsButtons to set the a. Use Set Tings option toDelay Input SetupCharacter Edit Use the arrowThen press Enter Repeat to enter up to Characters IntelliVolume Volume SetupPreferences Hdmi Setup DTR-7.6 Only OSD SetupLock Setup OSD PositionChanging the Remote Controller’s ID Remote IDsChanging the AV Receiver’s Remote ID Input, and then press Enter Use the Up and Down Digital Input Signal FormatsThat’s assigned to a digital input Opt, coax, or HDMI, and thenUsing Another Amp in Zone Connecting ZoneUsing Only Speakers in Zone ZoneZone 2 Out Setting Powered Zone 2 SettingUsing Zone Zone 2 Remote Mode but On the remote controller, pressTo adjust Ton, and then use the LevelRepeat this step as necessary for each setting Using the 12V Triggers in Zone 2 and the Main RoomDelay 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with a Cabinet Using a Multiroom Kit with ZoneUsing a Multiroom Kit with Other Components Controlling Other Components Entering Remote Control CodesRemote Control Codes for Integra Components Connected via Resetting the Remote ControllerResetting the Remote Mode Buttons Controlling Other ComponentsCH +/-, TV CH + On, Standby, TVPrev CH TV InputLearning Commands from Other Remote Controllers Making Macros Using MacrosRunning Macros Deleting MacrosTroubleshooting Troubleshooting Can’t learn commands from another remote controller Remote controller doesn’t workSound changes when I connect my head- phones Immediate display does not appearDTR-7.6,6.6.book Page 92 Monday, September 26, 2005 140 PM Amplifier Section SpecificationVideo Section Tuner SectionMemo DTR-7.6,6.6.book Page 95 Monday, September 26, 2005 140 PM 3 4 4 0 8

DTR-7.6/6.6 specifications

The Integra DTR-7.6 and DTR-6.6 are high-performance AV receivers that cater to audiophiles and home theater enthusiasts alike. Both models are designed to deliver exceptional audio quality and advanced features, making them ideal for a wide range of entertainment needs.

One of the standout characteristics of the DTR-7.6 and DTR-6.6 is their ability to support advanced audio formats, including Dolby Atmos and DTS:X. This enables users to experience immersive soundscapes by harnessing overhead sound for a three-dimensional auditory experience. The receivers also feature multiple speaker configuration options, allowing you to set up a customized surround sound experience based on your room’s size and shape.

In terms of power output, the DTR-7.6 offers an impressive power rating, providing ample drive for even the most demanding speaker systems. The DTR-6.6, while having a slightly lower power output, still boasts sufficient capabilities for medium to large home theater setups. Both models incorporate high-current amplifiers, ensuring clean and dynamic performance across all frequencies.

The inclusion of advanced video processing technologies further enhances the viewing experience. With support for 4K UHD video and HDR formats such as HDR10, Dolby Vision, and HLG, users can expect stunning picture quality and vibrant color reproduction. The receivers come equipped with multiple HDMI inputs, enabling users to connect various devices such as gaming consoles, Blu-ray players, and streaming devices effortlessly.

Connectivity options on both the DTR-7.6 and DTR-6.6 are extensive, featuring built-in Wi-Fi and Bluetooth for easy streaming from smartphones and tablets. Additionally, the receivers support popular streaming services, making it simple to access a vast library of music and entertainment. For those who value a seamless setup process, both models also support automated calibration through Audyssey MultEQ, which fine-tunes your system based on the unique acoustics of your space.

The sleek design of both receivers ensures they will fit well within any entertainment setup. The front panel includes an easy-to-navigate interface with a clear display, remote control functionality, and compatibility with smart home systems. Overall, the DTR-7.6 and DTR-6.6 are powerful, feature-rich receivers that stand out in the crowded AV market, offering a combination of advanced technologies and audio performance suitable for both casual listeners and serious audiophiles.
Top Page Image Contents