Roper Air Conditioner guide

9.Attach cabinet to finish frame. Drill 4 holes on each side and 2 holes in the top of the cabinet into the finish frame. Use #10 x 1” (25 mm) wood screws to attach cabinet to the frame. See Figure 26.

IMPORTANT: Do not over-tighten screws or the cabinet will distort and provide a poor air seal between the cabinet and the air conditioner.

10.Place the 2%” (63.5 mm) seal strip (J) inside the cabinet. Make sure the seal is flush with the cabinet front edge. See Figure 27.

NOTE: This seal strip fits between the air conditioner base and the cabinet.

11.Inset-l drain cup (T). Place drain cup through hole in cabinet rail. See Figure 28.

12.Insert air conditioner into cabinet.

13.Reattach ground wire with grounding screw. Put excess grounded wire between the coils and the cabinet.

Electrical Shock Hazard

Air conditioner ground wire must be attached to the cabinet.

Failure to do so could result in electrical shock.

14.Attach the front panel. Remove the 2 front panel screws from unit base. Replace front panel by pushing it straight on and then lowering it slightly to lock it in place. Attach bottom front of panel by reinserting the 2 front panel screws. See Figure 29.

15.Caulk all outside wall openings around the installa- tion and cabinet.

16.Install decorative molding. If desired, install molding around room side of cabinet.

9.Colocar la caja metelica en el marco de acabado. Taladrar 4 agujeros a cada lado y 2 a traves de la pane superior de la caja metalica hacia el marco. Usar 10s tornillos de madera #10 x 25 mm (1”) para sujetar la caja metalica al marco. Ver Figura 26.

IMPORTANTE: No apretar demasiado 10s tornillos pues la caja metalica se deformara y no obturara bien el aire entre la caja metalica y el acondicionador de aire.

10.Colocar la cinta obturadora de 63,5 mm (2.5”) (J) dentro de la caja metslica. Asegurarse de que la cinta obturadora este al ras con el borde delantero de la caja metalica. Ver Figura 27.

NOTA: Esta cinta obturadora calza entre la base del acondicionador de aire y la caja metalica.

11.lnsertar la taza de drenaje (T). Colocar la taza de drenaje a traves del agujero en el travesafio de la caja. Ver Figura 28.

12.lnsertar el acondicionador de aire en la caja metalica.

13.Volver a in&alar el alambre de puesta tierra en el tornillo de puesta tierra. Colocar el exceso del alambre de puesta a tierra entre 10s serpentines y la caja metalica.

Riesgo de Choque Electrico

El alambre de puesta a tierra del acondicionador de aire debe ser conectado a la caja metalica de lo contrario se puede ocasionar un choque electrico.

14. lnstalar el panel delantero. Sacar 10s 2 tornillos del panel

delantero que estan en la base del artefacto. Volver a colocar el panel delantero empujandolo derecho y luego haciendolo descender ligeramente para que se trabe en su lugar. Sujetar la parte inferior del panel delantero volviendo a inset-tar 10s 2 tornillos de la base. Ver Figura 29.

15.Calafatear todas las abet-turas de la pared exterior alrededor de la instalacibn y de la caja mettilica.

16.lnstalar moldura decorativa. Si se desea, instalar moldura alrededor de la caja metalica por el lado de la habitation.

Air Conditioner specifications

Roper air conditioners are a popular choice for those seeking reliable cooling systems for their homes or offices. Known for their affordability and efficiency, Roper offers a range of products that cater to diverse cooling needs. These air conditioners come with various features designed to enhance comfort while being easy to operate and maintain.

One of the standout features of Roper air conditioners is their energy efficiency. Many models are equipped with energy-saving technology, allowing users to keep energy costs low while maintaining a comfortable indoor climate. The Energy Efficiency Ratio (EER) ratings of Roper units are designed to comply with modern standards, making them an eco-friendly option for consumers conscious of their environmental impact.

Roper air conditioners also prioritize user-friendliness. Most models are equipped with simple control interfaces, allowing users to easily adjust temperature settings, fan speed, and mode of operation. Some advanced models even incorporate programmable timers, enabling homeowners to set cooling schedules that align with their daily routines, further optimizing energy consumption.

In terms of technologies, Roper air conditioners often feature advanced cooling systems with multiple speed settings. This allows for customizable airflow, ensuring that users can achieve their desired level of comfort. Additionally, many models are designed with a dehumidification function, which helps to remove excess moisture from the air, creating a more pleasant indoor environment.

Another characteristic that makes Roper air conditioners stand out is their compact and portable designs. Many units are designed for window installation or can be used as portable air conditioners, giving users flexibility in placement and operation. This makes them an ideal solution for apartments or spaces where traditional central air conditioning systems may be impractical.

Furthermore, Roper air conditioners often come with easy-to-clean filters, promoting better air quality by reducing dust and allergens in the home. Regular maintenance is straightforward, enabling users to keep their units running efficiently over a longer period.

In conclusion, Roper air conditioners are an excellent choice for those looking for cost-effective and efficient cooling solutions. With their focus on energy efficiency, user-friendly design, advanced cooling technologies, and compact features, Roper air conditioners provide comfort and convenience for any setting. Whether for home use or office environments, Roper stands as a reliable option in the competitive air conditioning market.