Wayne-Dalton 9600 installation instructions Positioning Support Bracket, Installation

Page 25
Positioning Support Bracket

25

Positioning Support Bracket

 

Tools Needed:

NOTE: See idrive® main installation and

Power Drill

owners manual for idrive® parts.

 

1/8” Drill Bit

NOTE: idrive® must be installed on a

solid mounting surface.

7/16” Socket

 

Driver

Locate the mounting surface. The

 

 

mounting surface is a vertical board

 

running directly above the center of the

45 angle

Antenna

mounting

 

wire

 

surface

 

 

door. Remove (2) 1/4”-20 flange nuts

from bottom of opener.

NOTE: Do not discard flange nuts.

Place the support bracket underneath

opener, to the right side of motor,

centered on mounting surface. Using a

tape measure, level the bottom of the

TorqueMaster® spring tube to the top of

the door section with the idrive® resting

on the support bracket. Once

TorqueMaster® spring tube is level, drill

1/8” pilot holes for the lag screws. Then

secure support bracket to the mounting

surface with (2) 1/4” x 1-1/2" lag

screws.

 

1/4” X

 

1-1/2” LAG

(Header)

SCREWs

 

TOP OF DOOR

TorqueMaster® spring tube

Manual background SUPPORT

BRACKET

1/4” - 20

FLANGE NUTS

mounting

studs

INSTALLATION

IMPORTANT: TorqueMaster® spring

tube must be level after support

bracket is fasten to mounting

surface.

NOTE: If wood mounting surface is

behind dry wall, use 1/4” x 2” lag

screws.

Lift and slide the opener over the

support bracket, aligning the mounting

studs with the bracket slots. Loosely

fasten to mounting studs with the (2)

1/4”-20 flange nuts.

NOTE: Do not tighten 1/4”-20 flange

nuts to opener studs at this time.

Remove the temporary orange label

holding the antenna wire. Straighten

antenna wire and angle it 45 degrees to

the right.

NOTE: Do not coil the antenna wire.

This will reduce the radio signal range.

mounting

studs bracket slots

 

support

TorqueMaster®

bracket

spring tube

 

(2) 1/4” - 20

flange nuts

“x”

“x”

“x”

 

top section

 

Using a tape measure, maintain an equal measurement “x” (top of door to bottom of Torquemaster® tube) at both ends and the center.

25

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Image 25
Contents TorqueMaster - Single and Double Spring 9100, 9400, ANDDefinition of key words used in this manual Table of ContentsPackage Contents Door Section Identification Tools Required Page TorqueMaster Spring Removal PRE-INSTALLATIONRemoval continued TorqueMaster SpringExtension Spring Removal PRE-INSTALLATIONRemoving the Old Door Failure to securely Preparing the Openingattach a suitable mounting pad to structurally soundAttaching Quick Install Flag InstallationINSTALLATION Angle to Vertical TrackHorizontal Angle INSTALLATION Installing Q.I. Jamb BracketsDrums Vertical Track Bottom SectionTop Brackets Stacking SectionsU-Bar- Asymmetrical U-BarOperator Bracket INSTALLATIONTop Section Attaching Quick Install Flagangleto Horizontal Track Adjusting Top Brackets Attaching Adjustable Flagangleto Horizontal Track Center Bracket Bushing TorqueMaster Spring Tubeidrive Installation Cable Drum Installation INSTALLATION Drive Gear InstallationTools Needed Power Drill 3/16” Drill Bit 7/16” End BracketsAssembly Counter InstallationSecuring Center Bracket Positioning Support Bracket INSTALLATIONMounting Disconnect Attaching Disconnect CablesHandle Bracket Attaching Disconnect Handle Securing Door for Spring Winding Cable AdjustmentsTools Needed Vice Clamp Tools Needed Locking Pliers Flat Tip ScrewdriverSetting Spring Tension INSTALLATIONWinding Bolt Rotation Drum Wrap Installation Rear Support Continued INSTALLATIONDoorMasterTM Bracket Side LockStep Plate OPTIONAL INSTALLATIONPull Rope Standard Lift Trolley Installation forOPTIONAL INSTALLATION Trolley Installation for Low HeadroomTrolley Operator MAINTENANCE CleaningPainting Painting Continued Lifetime Limited Warranty Models Thank you for your purchase Please Do Not Return This Product To The Store
Related manuals
Manual 8 pages 50.32 Kb Manual 10 pages 39.36 Kb Manual 8 pages 41.15 Kb Manual 40 pages 42.94 Kb Manual 36 pages 11.38 Kb Manual 2 pages 9.98 Kb

9600 specifications

Wayne-Dalton is a renowned name in the garage door industry, and its series of garage doors, namely the 9600, 9400, and 9100, stand out for their exceptional quality, durability, and aesthetic appeal. Each series is designed to meet various needs, offering a range of features and technologies that enhance functionality and performance.

The Wayne-Dalton 9600 series is known for its energy efficiency and robust construction. These doors are insulated with a foamed-in-place polyurethane core, which provides an exceptional R-value, making them ideal for regions with extreme temperature fluctuations. The 9600 series features high-quality steel construction, ensuring durability and resistance to dents and damage. This series also offers a variety of design options, including wood grain textures and multiple color finishes, allowing homeowners to match their garage doors with their home’s exterior.

Moving to the Wayne-Dalton 9400 series, this line is recognized for its versatility and premium insulation. Like the 9600 series, the 9400 features a polyurethane core foamed between two layers of steel for superior thermal performance. Moreover, it offers a wider selection of panel designs, from traditional to contemporary finishes. The 9400 doors come equipped with a weather seal, enhancing protection against the elements and keeping the garage environment comfortable year-round.

Lastly, the Wayne-Dalton 9100 series combines affordability with functionality. It also offers insulated construction, although with a polystyrene core, making it an excellent choice for homeowners seeking a budget-friendly option without sacrificing quality. The 9100 series provides a good range of design options and customizable accessories such as decorative hardware, windows, and color choices to suit individual preferences.

All three series benefit from advanced technology, such as Wayne-Dalton's innovative design features for smooth operation and increased safety. They are equipped with sectional door designs, reducing the risk of pinch points and enhancing user safety. Additionally, Wayne-Dalton offers a variety of remote access and control technologies, ensuring convenience and peace of mind for users.

In summary, the Wayne-Dalton 9600, 9400, and 9100 series are distinguished by their superior insulation, durability, and stylish design options. Whether prioritizing energy efficiency, versatility, or budget considerations, these garage doors cater to a spectrum of consumer needs, thereby continuing Wayne-Dalton's legacy of excellence in design and functionality.