Wayne-Dalton 9600, 9400, 9100 Rear Support, Keep horizontal track, Parallel and within 3/4, Death

Page 26

21

Rear Support

 

Tools Needed:

WARNING

 

Ratchet Wrench

Keep horizontal track

 

1/2” Socket

parallel and within 3/4”

maximum of door edge,

 

1/2” Wrench

otherwise door could fall,

 

resulting in severe injury or

(2) Vice Clamps

death.

 

Raise the door until the top section and

 

half of the next section are in a horizontal

 

position. Do not raise door any further

 

since rear of horizontal track is not yet

 

supported.

WARNING

Raising door further can result in door falling and cause severe injury or death.

Clamp a pair of vice clamps on the vertical tracks just above the second roller on one side, just below the second roller on the other side. This will prevent the door from raising or lowering while installing the rear support.

Using perforated angle, 5/16” x 1-5/8” hex head lag screws and 5/16” bolts with nuts (may not be supplied), fabricate rear support for horizontal tracks. Attach horizontal tracks to the rear supports with 5/16”- 18 x 1-1/4” hex bolts and nuts (may not be supplied). Horizontal tracks must be level and parallel with door.

NOTE: If rear supports are to be installed over drywall, use 5/16” x 2” hex head lag screws.

Adjust weather seal (if necessary) Now permanently attach the weather seal to both door jambs and header. (Temporarily attached in PREPARING THE OPENING on page 10.) Avoid pushing weather seal stop too tightly against face of door.

DOOR IN THE

UP POSITION

vice clamps

vertical

TRACK

Door Edge

3/4”

Horizontal Track

26

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com

Page 25 Page 27
Image 26
Page 25 Page 27
Contents 9100, 9400 Portland Source PlantTable of Contents Package Contents Door Section Identification Tools Required LevelFailure to use approved Spring when the set screws areTorsion Spring Removal For Standard Lift Experienced door technician. Instead haveTorqueMaster Spring Removal Unwind SpringsBracket and Drive Gear Extension Spring Removal Removing the Old DoorSecurely attach a Preparing the OpeningFailure to Suitable mounting pad to structurallyFlagangle to Vertical Track InstallationAttaching Fully Adjustable Hand tighten the flagangle toMeasure the length of the vertical Installing Q.I. Jamb BracketsHole Middle Bottom Quick install feature Left side shownDrums Bottom SectionVertical Track Stacking Sections Top Brackets Bar Bar AsymmetricalOperator Bracket Important When Installing aAdjusted Properly Top Section Door OperationDo not Raise Door Until Horizontal Adjusting Top BracketsFlagangle Torsion End Bearing Brackets Center Bearing BracketTorsion Spring Assembly SideNylon Center Bushing For Spring Winding Counterbalance CablesSecuring Door Important do not USE Impact GUN To Wind SpringsWinding Torsion Springs Parallel and within 3/4 Rear SupportKeep horizontal track Maximum of door edgeWinding bar while carefully loosening To adjust spring tension, fully closeThird roller. Insert a winding bar into Set screws in the winding coneSide Lock Pull RopeStep Plate Failure to use locking nut can result Trolley Installation forStandard Lift Arm releasing and possible resultingPoint, on the header wall. Raise the door slightly until Low HeadroomDetermine center line of door. Mark vertical line at this Top section reaches the highest point of travel high arcPerforated OPERATORangle rail Trolley OperatorHeader Door ARM to Operator Bracket Operator Framing Members Perforated AngleAcrylic Cleaning Instructions CleaningGlass Cleaning Instructions PaintingPainting Lifetime Limited Warranty Models 9100, 9400 Thank you for your purchase
Related manuals
Manual 8 pages 50.32 Kb Manual 10 pages 39.36 Kb Manual 8 pages 41.15 Kb Manual 40 pages 4.99 Kb Manual 40 pages 42.94 Kb Manual 2 pages 9.98 Kb Manual 9 pages 37.96 Kb Manual 48 pages 56.14 Kb

9600, 9100, 9400 specifications

Wayne-Dalton is a renowned name in the garage door industry, and its series of garage doors, namely the 9600, 9400, and 9100, stand out for their exceptional quality, durability, and aesthetic appeal. Each series is designed to meet various needs, offering a range of features and technologies that enhance functionality and performance.

The Wayne-Dalton 9600 series is known for its energy efficiency and robust construction. These doors are insulated with a foamed-in-place polyurethane core, which provides an exceptional R-value, making them ideal for regions with extreme temperature fluctuations. The 9600 series features high-quality steel construction, ensuring durability and resistance to dents and damage. This series also offers a variety of design options, including wood grain textures and multiple color finishes, allowing homeowners to match their garage doors with their home’s exterior.

Moving to the Wayne-Dalton 9400 series, this line is recognized for its versatility and premium insulation. Like the 9600 series, the 9400 features a polyurethane core foamed between two layers of steel for superior thermal performance. Moreover, it offers a wider selection of panel designs, from traditional to contemporary finishes. The 9400 doors come equipped with a weather seal, enhancing protection against the elements and keeping the garage environment comfortable year-round.

Lastly, the Wayne-Dalton 9100 series combines affordability with functionality. It also offers insulated construction, although with a polystyrene core, making it an excellent choice for homeowners seeking a budget-friendly option without sacrificing quality. The 9100 series provides a good range of design options and customizable accessories such as decorative hardware, windows, and color choices to suit individual preferences.

All three series benefit from advanced technology, such as Wayne-Dalton's innovative design features for smooth operation and increased safety. They are equipped with sectional door designs, reducing the risk of pinch points and enhancing user safety. Additionally, Wayne-Dalton offers a variety of remote access and control technologies, ensuring convenience and peace of mind for users.

In summary, the Wayne-Dalton 9600, 9400, and 9100 series are distinguished by their superior insulation, durability, and stylish design options. Whether prioritizing energy efficiency, versatility, or budget considerations, these garage doors cater to a spectrum of consumer needs, thereby continuing Wayne-Dalton's legacy of excellence in design and functionality.
Top Page Image Contents