Heat & Glo LifeStyle COSMO-I35 Maintenance and Service, Doors, Surrounds, Fronts, Glass Cleaning

Page 12

3 Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

When properly maintained, your appliance will give you many years of trouble-free service. We recommend an- nual service by a qualified technician.

Doors, Surrounds, Fronts

Frequency: Annually

By: Homeowner

Tools needed: Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualified techni- cian only. The appliance should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service ap- pointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the appliance must be kept clean.

CAUTION! Risk of Burns! The appliance should be turned off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally

By: Homeowner

Tools Needed: Protective gloves, glass cleaner, drop cloth and a stable work surface.

CAUTION! Handle fixed glass assembly with care. Glass is breakable.

•Avoid striking, scratching or slamming glass

•Avoid abrasive cleaners

•DO NOT clean glass while it is hot

•Prepare a work area large enough to accommodate fixed glass assembly and door frame by placing a drop cloth on a flat, stable surface.

Note: Fixed glass assembly and gasketing may have res- idue that can stain carpeting or floor surfaces.

•Remove door or decorative front from appliance and set aside on work surface.

•See Section 12.F for instructions to remove fixed glass assembly.

•Clean glass with a non-abrasive commercially available cleaner.

-Light deposits: Use a soft cloth with soap and water

-Heavy deposits: Use commercial fireplace glass cleaner (consult with your dealer)

•Carefully set fixed glass assembly in place on appliance. Hold glass in place with one hand and secure glass latches with the other hand.

•Reinstall door or decorative front.

•Inspect for scratches, dents or other damage and repair as necessary.

•Check that louvers are not blocked.

•Vacuum or dust surfaces.

Remote Control

Frequency: Seasonally

By: Homeowner

Tools needed: Replacement batteries and remote con- trol instructions.

•Locate remote control transmitter and receiver.

•Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

•Place batteries as needed in remote transmitters and battery-powered receivers.

•Place remote control out of reach of children.

If not using your fireplace for an extended period of time (summer months, vacations/trips, etc), to prevent unin- tended operation:

• Remove batteries from remote controls.

12

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Models Cosmo-I30 Cosmo-I35 What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents User GuideLimited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesIPI Battery Tray/Battery Installation Clear SpaceModule Reset Control Module OperationBefore Lighting Fireplace Lighting Instructions IPI Final inspection byFrequently Asked Questions After Appliance is LitMaintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote ControlMaintenance Tasks-Service Technician Gasket Seal and Glass Assembly InspectionVenting FireboxBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Fireplace Size Requirements Minimum Fireplace OpeningMantel and Wall Projections Side ViewTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVent Limits Venting ComponentsLocation of AUX300 for Remote Control Blower Function Placing, Securing and Leveling the Appli- anceInstalling Adaptor and Termination Cap MasonryFactory Built Wood Burning Damper Flashing Kit OptionalGas Information Fuel ConversionGas Pressure Gas ConnectionWiring Requirements IntelliFire Plus Ignition System WiringON/OFF Switch Electrical InformationOptional Accessories Requirements BRN To Valve Bracket BLK Ground RE DFan Wiring with Remote See .H for control module operation instructionsFinishing Clearances to Mantels or other Combustibles above ApplianceAppliance Setup Air Shutter Setting Air Shutter SettingsTroubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System To remove any contaminants that may have accumulated on flame Appliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsService Parts Part number list on followingModern Metal Insert, IPI Service Parts List At DepotCOSMO-I35 COSMO-I35 StockedCOSMO-I30, COSMO-I35 Contact Information

COSMO-I35, COSMO-I30 specifications

The Heat & Glo LifeStyle COSMO-I30 and COSMO-I35 fireplaces are revolutionary additions to modern living spaces, merging outstanding design with advanced technology. Both models are designed to enhance your home's aesthetics while providing efficient heating solutions.

The COSMO-I30 is a 30-inch linear fireplace, while the COSMO-I35 is the larger 35-inch version, allowing homeowners to choose the perfect size to complement their space. These zero-clearance fireplaces can be easily installed in various locations, including existing masonry or prefabricated fireplaces, or even as stand-alone features. This versatility makes them suitable for both remodeling projects and new constructions.

One of the standout features of both models is the innovative design that emphasizes a contemporary look. The clean, linear flame provides a warm ambiance without the clutter of traditional fireplaces. You can enjoy the dancing flames through a sleek front glass panel that maintains a clear view of the fire while enhancing safety.

The COSMO series incorporates advanced technology to ensure optimal performance and energy efficiency. Both models utilize proprietary technology that allows for reliable operation and minimal emissions. The Intellifire ignition system further enhances convenience, providing instant lighting with the push of a button. Homeowners can easily control the flames and heat output, adjusting the ambiance to suit their preferences.

Customizability is another appealing aspect of the COSMO series. The fireplaces come with a range of decorative options, including different styles of media such as glass, stones, or logs, allowing you to tailor the appearance to match your interior design. The ambient lighting feature adds another layer of sophistication, providing a soft glow that can be enjoyed even when the fire isn’t lit.

Both the COSMO-I30 and COSMO-I35 are energy-efficient, boasting high-efficiency ratings that help reduce heating costs without sacrificing comfort. They are designed to function efficiently, effectively distributing heat throughout the room.

With their striking design, innovative technology, and customizable options, the Heat & Glo LifeStyle COSMO-I30 and COSMO-I35 fireplaces create the perfect focal point in any living space, combining functionality with elegance for an unparalleled home experience.
Top Page Image Contents