Heat & Glo LifeStyle COSMO-I30, COSMO-I35 Installing Adaptor and Termination Cap, Masonry

Page 23

F. Installing Adaptor and Termination Cap

For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 8.4) .

To install adaptor see Figure 8.5.

HORIZONTAL

OVERHANG

CAUTION! Risk of Cuts/Abrasions/Flying Debris.

Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp.

Damper Flashing Kit (Optional)

For use with LINK-DV30B or LINK-DV4-30B Liner Kit. Note: Damper may have to be removed to use this kit.

•

Run flex liners through 3 in. holes in damper flashing.

•

Attach damper flashing to firebox roof with self tapping

2FT.

MIN.

GAS DIRECT VENT

TERMINATION CAP

20 INCHES MIN.

VERTICAL

LOWEST

WALL

 

DISCHARGE

 

OPENING

 

X

12

ROOF PITCH

IS X/ 12

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

screws included in kit.

CLASS A PIPE

Roof Pitch

H (Min.) Ft.

Flat to 6/12

....................

1.0*

Over 6/12 to 7/12

1.25*

Over 7/12 to 8/12

1.5*

Over 8/12 to 9/12

2.0*

Over 9/12 to 10/12

2.5*

Over 10/12 to 11/12

3.25

Roof Pitch

H (Min.) Ft.

Over 11/12 to 12/12

4.0

Over 12/12 to 14/12

5.0

Over 14/12 to 16/12

6.0

Over 16/12 to 18/12

7.0

Over 18/12 to 20/12

7.5

Over 20/12 to 21/12

8.0

Figure 8.5

* 3 foot minimum in snow regions

Figure 8.4 Minimum Height from Roof to Lowest Discharge Opening

To help eliminate cold air drafts, it may be necessary to place non- combustible insulation around the flues as they go though the damper.

Note: The LINK-DV4-30B

system REQUIRES this insulation.

Masonry

LINK-DV30B

LINK-DV4-30B

Installation

Installation

Factory Built

Wood Burning

 

TERMINATION

 

CAP

EXHAUST

EXHAUST

AIR

AIR

VENT PIPE

VENT PIPE

 

OR

 

INLET AIR

 

VENT PIPE

Figure 8.6

 

WARNING:

DO NOT BLOCK

THIS PIPE END!

Note: Untwist the pipe while extend- ing it, to achieve full 30’ length.

INLET AIR

VENT PIPE

OPTIONAL LINK-ZC-ADPB

FOR USE WITH CLASS A

WOODBURNING PIPE

Remove 18 inch x 18 inch flashing on cap by removing 3 screws. Connect both the LINK-ZC-ADPB to Class A Pipe and the termination cap to the LINK-ZC-ADPB with the self tapping screws provided.

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents What to do if you smell gas Models Cosmo-I30 Cosmo-I35Homeowner Reference Information CongratulationsUser Guide Table of ContentsLimited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches IPI Battery Tray/Battery InstallationBefore Lighting Fireplace Module ResetControl Module Operation Final inspection by Lighting Instructions IPIAfter Appliance is Lit Frequently Asked QuestionsRemote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningFirebox Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection VentingIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Minimum Fireplace Opening Fireplace Size RequirementsSide View Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Vent LimitsPlacing, Securing and Leveling the Appli- ance Location of AUX300 for Remote Control Blower FunctionDamper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory Built Wood BurningGas Connection Gas InformationFuel Conversion Gas PressureElectrical Information Wiring RequirementsIntelliFire Plus Ignition System Wiring ON/OFF SwitchBRN To Valve Bracket BLK Ground RE D Optional Accessories RequirementsSee .H for control module operation instructions Fan Wiring with RemoteClearances to Mantels or other Combustibles above Appliance FinishingAppliance Setup Air Shutter Settings Air Shutter SettingIntelliFire Plus Ignition System TroubleshootingSymptom Possible Cause Corrective Action To remove any contaminants that may have accumulated on flame Reference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsModern Metal Insert, IPI Service PartsPart number list on following At Depot Service Parts ListCOSMO-I35 Stocked COSMO-I35COSMO-I30, COSMO-I35 Contact Information

COSMO-I35, COSMO-I30 specifications

The Heat & Glo LifeStyle COSMO-I30 and COSMO-I35 fireplaces are revolutionary additions to modern living spaces, merging outstanding design with advanced technology. Both models are designed to enhance your home's aesthetics while providing efficient heating solutions.

The COSMO-I30 is a 30-inch linear fireplace, while the COSMO-I35 is the larger 35-inch version, allowing homeowners to choose the perfect size to complement their space. These zero-clearance fireplaces can be easily installed in various locations, including existing masonry or prefabricated fireplaces, or even as stand-alone features. This versatility makes them suitable for both remodeling projects and new constructions.

One of the standout features of both models is the innovative design that emphasizes a contemporary look. The clean, linear flame provides a warm ambiance without the clutter of traditional fireplaces. You can enjoy the dancing flames through a sleek front glass panel that maintains a clear view of the fire while enhancing safety.

The COSMO series incorporates advanced technology to ensure optimal performance and energy efficiency. Both models utilize proprietary technology that allows for reliable operation and minimal emissions. The Intellifire ignition system further enhances convenience, providing instant lighting with the push of a button. Homeowners can easily control the flames and heat output, adjusting the ambiance to suit their preferences.

Customizability is another appealing aspect of the COSMO series. The fireplaces come with a range of decorative options, including different styles of media such as glass, stones, or logs, allowing you to tailor the appearance to match your interior design. The ambient lighting feature adds another layer of sophistication, providing a soft glow that can be enjoyed even when the fire isn’t lit.

Both the COSMO-I30 and COSMO-I35 are energy-efficient, boasting high-efficiency ratings that help reduce heating costs without sacrificing comfort. They are designed to function efficiently, effectively distributing heat throughout the room.

With their striking design, innovative technology, and customizable options, the Heat & Glo LifeStyle COSMO-I30 and COSMO-I35 fireplaces create the perfect focal point in any living space, combining functionality with elegance for an unparalleled home experience.
Top Page Image Contents