Heat & Glo LifeStyle COSMO-I35, COSMO-I30 owner manual Stocked

Page 38

C. Service Parts List			COSMO-I35
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
					Stocked
parts for your appliance please provide model number and serial number. All parts listed					Stocked
in this manual may be ordered from an authorized dealer.					at Depot
ITEM	DESCRIPTION	COMMENTS	PART NUMBER
1	Termination Plate Assembly		2205-012
	Flex Pipe Handle		438-351
	Gasket		2206-401
2	Burner Assembly		2204-007		Y
3	Burner Leg		2238-103
4	Base Pan		2238-100
5	On/Off Rheostat		2206-800		Y
6	Glass Door Assembly		GLA-2205		Y
7	Rheostat Knob		100-512		Y
8	Control Panel		2205-129
9	Blower		GFK-210
10	Wire Assembly		2206-068		Y
11	Power cord Assembly		2201-017		Y


	Gasket Assembly		2206-080
	Gems. Black	Qty 2 req	MEDIA-BK-GEMS
	Glass Latch Assembly, Bottom	Qty 2 req	2155-045		Y
	Glass Latch Assembly, Top	Qty 2 req	339-121A		Y
	Glass Refractory, Back		2238-200
	Glass Refractory, Left		2238-201
	Glass Refractory, Right		2238-202
	Jumper wire		2187-198		Y
	Remote Wire Assembly		2103-013		Y
	Touch Up Paint		TUP-GBK-12

	Conversion Kit NG	NGK-COSMOI35	Y
	Conversion Kit LP	LPK-COSMOI35	Y
	Pilot Oriﬁce NG	2098-520	Y
	Pilot Oriﬁce LP	2098-512	Y
	Regulator NG	NGK-DXV-50	Y
	Regulator LP	LPK-DXV-50	Y

Additional service part numbers appear on following page.

38	Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11

Image 38

Contents

Models Cosmo-I30 Cosmo-I35 What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents User GuideLimited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide IPI Battery Tray/Battery Installation Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear SpaceBefore Lighting Fireplace Module ResetControl Module Operation Lighting Instructions IPI Final inspection byFrequently Asked Questions After Appliance is LitGlass Cleaning Maintenance and ServiceMaintenance Tasks-Homeowner Remote ControlVenting Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection FireboxBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Fireplace Size Requirements Minimum Fireplace OpeningMantel and Wall Projections Side ViewTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Vent Limits Installing Vent Pipe and ApplianceConnecting Vent Pipe Venting ComponentsLocation of AUX300 for Remote Control Blower Function Placing, Securing and Leveling the Appli- anceFactory Built Wood Burning Installing Adaptor and Termination CapMasonry Damper Flashing Kit OptionalGas Pressure Gas InformationFuel Conversion Gas ConnectionON/OFF Switch Wiring RequirementsIntelliFire Plus Ignition System Wiring Electrical InformationOptional Accessories Requirements BRN To Valve Bracket BLK Ground RE DFan Wiring with Remote See .H for control module operation instructionsFinishing Clearances to Mantels or other Combustibles above ApplianceAppliance Setup Air Shutter Setting Air Shutter SettingsIntelliFire Plus Ignition System TroubleshootingSymptom Possible Cause Corrective Action To remove any contaminants that may have accumulated on ﬂame Appliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsModern Metal Insert, IPI Service PartsPart number list on following Service Parts List At DepotCOSMO-I35 COSMO-I35 StockedCOSMO-I30, COSMO-I35 Contact Information