Heat & Glo LifeStyle COSMO-I35 Design and Installation Considerations, Tools and Supplies Needed

Page 16

B. Design and Installation Considerations

Heat & Glo gas inserts are designed for installations into solid fuel masonry or factory built fireplaces that have been installed in accordance with the National, Provin- cial, State and local building codes. Fireplaces are to be constructed of non-combustible materials and, in the ab- sence of local or regional codes, meet criteria of NFPA 211. No additional outside air source is required.

Installation MUST comply with local, regional, state and na- tional codes and regulations. Consult insurance carrier, local building inspector, fire officials or authorities having jurisdic- tion over restrictions, installation inspection and permits.

Prior to installing the gas insert:

•Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certi- fied professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.

•Replace component parts of the chimney and fireplace as specified by the professionals.

•Ensure combustible mantel and surround clearances comply with applicable codes and regulations for solid- fuel fireplaces. In the absence of local or regional codes, refer to NFPA 211.

•Ensure all joints are properly engaged and the chimney is properly secured.

•Minimum fireplace size. See Section 5.A.

•Gas supply piping requirements.

•Electrical wiring requirements.

•Finishing details.

•Whether optional accessories—devices such as a wall switch or remote control—are desired.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Tape measure

Framing material

Pliers

Flat blade screwdriver

Hammer

Phillips screwdriver

Gloves

Framing square

Voltmeter

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Reciprocating saw

Manometer

Noncorrosive leak check solution

1/2 - 3/4 inch length, #6 or #8 Self-drilling screws

Caulking material (300º F minimum continuous exposure rating)

Stove cement (1200ºF or higher continuous exposure rating)

D. Inspect Appliance and Components

•Carefully remove the appliance and components from the packaging.

•The vent system components and decorative doors and fronts may be shipped in separate packages.

•If packaged separately, the log set and appliance grate must be installed.

•Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

•Read all of the instructions before starting the instal- lation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, in- complete or substitute components. Keep appliance dry.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

•Installation and use of any damaged appliance or vent system component.

•Modification of the appliance or vent system.

•Installation other than as instructed by Hearth & Home Technologies.

•Improper positioning of the gas logs or the glass door.

•Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

WARNING! Risk of Fire,/Explosion/Electric Shock! DO NOT use this appliance if any part has been under water. Call a qualified technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water.

16

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Models Cosmo-I30 Cosmo-I35 What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents User GuideLimited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesIPI Battery Tray/Battery Installation Clear SpaceControl Module Operation Module ResetBefore Lighting Fireplace Lighting Instructions IPI Final inspection byFrequently Asked Questions After Appliance is LitMaintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote ControlMaintenance Tasks-Service Technician Gasket Seal and Glass Assembly InspectionVenting FireboxBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Fireplace Size Requirements Minimum Fireplace OpeningMantel and Wall Projections Side ViewTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVent Limits Venting ComponentsLocation of AUX300 for Remote Control Blower Function Placing, Securing and Leveling the Appli- anceInstalling Adaptor and Termination Cap MasonryFactory Built Wood Burning Damper Flashing Kit OptionalGas Information Fuel ConversionGas Pressure Gas ConnectionWiring Requirements IntelliFire Plus Ignition System WiringON/OFF Switch Electrical InformationOptional Accessories Requirements BRN To Valve Bracket BLK Ground RE DFan Wiring with Remote See .H for control module operation instructionsFinishing Clearances to Mantels or other Combustibles above ApplianceAppliance Setup Air Shutter Setting Air Shutter SettingsSymptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System To remove any contaminants that may have accumulated on flame Appliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsPart number list on following Service PartsModern Metal Insert, IPI Service Parts List At DepotCOSMO-I35 COSMO-I35 StockedCOSMO-I30, COSMO-I35 Contact Information

COSMO-I35, COSMO-I30 specifications

The Heat & Glo LifeStyle COSMO-I30 and COSMO-I35 fireplaces are revolutionary additions to modern living spaces, merging outstanding design with advanced technology. Both models are designed to enhance your home's aesthetics while providing efficient heating solutions.

The COSMO-I30 is a 30-inch linear fireplace, while the COSMO-I35 is the larger 35-inch version, allowing homeowners to choose the perfect size to complement their space. These zero-clearance fireplaces can be easily installed in various locations, including existing masonry or prefabricated fireplaces, or even as stand-alone features. This versatility makes them suitable for both remodeling projects and new constructions.

One of the standout features of both models is the innovative design that emphasizes a contemporary look. The clean, linear flame provides a warm ambiance without the clutter of traditional fireplaces. You can enjoy the dancing flames through a sleek front glass panel that maintains a clear view of the fire while enhancing safety.

The COSMO series incorporates advanced technology to ensure optimal performance and energy efficiency. Both models utilize proprietary technology that allows for reliable operation and minimal emissions. The Intellifire ignition system further enhances convenience, providing instant lighting with the push of a button. Homeowners can easily control the flames and heat output, adjusting the ambiance to suit their preferences.

Customizability is another appealing aspect of the COSMO series. The fireplaces come with a range of decorative options, including different styles of media such as glass, stones, or logs, allowing you to tailor the appearance to match your interior design. The ambient lighting feature adds another layer of sophistication, providing a soft glow that can be enjoyed even when the fire isn’t lit.

Both the COSMO-I30 and COSMO-I35 are energy-efficient, boasting high-efficiency ratings that help reduce heating costs without sacrificing comfort. They are designed to function efficiently, effectively distributing heat throughout the room.

With their striking design, innovative technology, and customizable options, the Heat & Glo LifeStyle COSMO-I30 and COSMO-I35 fireplaces create the perfect focal point in any living space, combining functionality with elegance for an unparalleled home experience.
Top Page Image Contents