Heatiator CL36D owner manual 6Framing & Clearances, A. Select Fireplace Location

Page 18

6Framing & Clearances

A. Select Fireplace Location

		As room divider
		23 in.
		45 in.
	48 in. Min.	18 in. minimum from
	48 in. Min.	front opening to sidewall
		front opening to sidewall
		45 in.
		23 in.

48 in. Min.

Note: 18 in. minimum from front opening to sidewall.

Note: 1/2 in. min. distance from fireplace to combustible materials.

Note: In addition to these framing dimensions, also reference the following sections:

•Clearances (Section 6.B.)

•Mantel Projections (Section 11.E.)

•Fireplace Dimensions (Section 13.A.)

Figure 6.1 Fireplace Locations (Framing dimensions shown)

18	Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12

Image 18

Contents Wood Burning Fireplace Owner’s ManualModels CL36D CR36D Listing Label Information/Location CongratulationsHomeowner Reference Information FIREPLACE NOSafety Alert Key Table of ContentsInstaller Guide User GuideWARRANTY COVERAGE Limited Warranty Hearth & Home Technologies IncLIMITED LIFETIME WARRANTY WARRANTY PERIODThis warranty is void if WARRANTY CONDITIONSWARRANTY EXCLUSIONS LIMITATIONS OF LIABILITYB. Non-CombustibleMaterials 1Listing and Code ApprovalsA. Appliance Certification C. Combustible MaterialsA. Your Fireplace User Guide2Operating Instructions Hot glass will cause burnsD. Grate B. Seasoned WoodC. Starting a Fire E. FirescreenJ. Vented Gas Log Sets & Gas Log Lighters H. Glass DoorsI. Outside Air optional K. Optional ComponentsMoisture M. Wood FuelHardwood vs Softwood Seasoned WoodA. Disposal of Ashes 3Maintenance and ServiceB. Chimney Inspection/Cleaning Creosote - Formation and Need for RemovalD. Inspect Grate E. Glass CleaningC. Check Firebox Refractory Frequency: As desiredSolution 4Troubleshooting GuideStart Fire Problems Possible CauseA. Typical Fireplace System Installer Guide5Getting Started •Illustrations/diagrams are not drawn to scaleB. Design and Installation Considerations C. DraftD. Negative Pressure E. Locating Fireplace & Chimney F. Tools and Supplies Needed G. Fireplace System RequirementsH. Inspect Fireplace and Components 6Framing & Clearances A. Select Fireplace LocationB. Clearances Heatilator • CL36D, CR36D • 12538 • Rev Z 7/1239 deg C. Sidewalls/Surrounds20 in 50 degD. Frame the Fireplace B. Position the Fireplace 7Installation of FireplaceA. Things to Consider C. Place Protective Metal Hearth StripsCanada Note: Chimney air kit notshown, but required in Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12E. Install Outside Air Kit 8Chimney Assembly A. Chimney Requirements TableB. Using Offsets/Returns TableExample D. Install Chimney Air Kit E. Install Ceiling FirestopsC. Assemble Chimney Sections F. Install Attic Insulation Shield H. Complete Installation I. Install FlashingG. Cut out Hole in Roof J. Chimney Termination Requirements 9Chase Installations A. Construct the ChaseC. Install Chase Top B. Install Fireplace & ChimneyD. Install Termination Cap •Warning! Risk of Fire! The minimum overlap of•ST375 Square Termination Cap •TR342 Round Telescoping Termination Cap•TS345/TS345P Square Termination Cap •TCT375 Terra Cotta Cap10 Shrouds A. Radiation ShieldB. Field Constructed Shrouds Roofed Style Shroud radiation shield required Figure 10.4 Roofed Style Shroud DimensionsMailbox Style Shroud radiation shield required Heatilator CL36D, CR36D 12538 Rev Z 7/12B. Combustible Materials 11 FinishingA. Non-combustibleMaterials C. Hearth ExtensionD. Finishing Material Warning! Risk of FireE. Combustible Mantel MantelSidewalls/Surrounds B. Wood Burning Inserts 12 AccessoriesA. Gas Log/Lighter Provision Gas Code, ANSI Z223.1A. Fireplace Dimensions 13 Reference MaterialsB. Optional Components C. Chimney Components Catalog #14-1/2in 368 mmHeatilator • CL36D, CR36D • 12538 • Rev Z 7/12 Stocked D. Service PartsCL36D at DepotStocked D. Service Parts continuedCR36D at DepotDO NOT DISCARD THIS MANUAL – NOTES –E. Contact Information DO DISCARDNOT

Related manuals

Manual 48 pages 11.28 Kb