Heatiator CL36D 7Installation of Fireplace, A. Things to Consider, B. Position the Fireplace

Page 22

7Installation of Fireplace

7Installation of Fireplace

Caution! Risk of Cuts/Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

A. Things to Consider

•Location of chimney air kit (see Figure 7.4)

•Location of outside air kit

•Electrical connections and/or wall switch

•Gas line piping

B. Position the Fireplace

•Place the fireplace on a continuous flat surface.

•Follow framing instructions in Section 6.

Warning! Risk of Fire! Prevent contact with sag- ging, loose insulation.

•DO NOT install against vapor barriers or exposed insulation.

•Secure insulation and vapor barriers.

•Provide minimum air space clearances at the sides and back of the fireplace assembly as outlined in Section 6.

C. Place Protective Metal Hearth Strips

Warning! Risk of Fire! Protective metal hearth strips MUST be installed. DO NOT cover metal strips with com- bustible materials. Sparks or embers may ignite flooring.

•Refer to Figures 7.1 and 7.2.

•Locate the two protective metal hearth strips measuring approximately 26 in. x 4 in. (660 mm x 102 mm) included with this fireplace.

•Slide each metal strip 2 in. (51 mm) under front edge of fireplace.

•Overlap strips in the middle of the front fireplace opening by 1 in. (25 mm) minimum.

•Metal strips must extend beyond the front and sides of the fireplace opening by at least 2 in. (51 mm).

•Protect the front of a platform elevated above the hearth extension with metal strips (not included with fireplace) per Figure 7.2. See Section 11 for hearth extension instructions.

D. Level Fireplace

•Level fireplace side-to-side and front-to-back.

•Shim with non-combustible material as necessary.

•Secure fireplace to framing with nailing flanges with a minimum of two fasteners per nailing flange.

•Check fireplace opening for square to ensure proper fit of glass doors. Measure diagonals of fireplace opening to make sure they are equal.

1" OVERLAP

Metal strip 2 in. (51 mm) under edge of fireplace openings and hearth extension.

Figure 7.1 Position the Protective Metal Hearth Strips

	Top piece must overlap
	bottom piece
	Raised Platform
2 in.	1 in. (25 mm) min.
(51 mm)	overlap

Floor

2 in.

(51 mm)

Figure 7.2 Protect the Front of an Elevated Platform

22	Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12

Image 22

Contents Owner’s Manual Wood Burning FireplaceModels CL36D CR36D Listing Label Information/Location CongratulationsHomeowner Reference Information FIREPLACE NOSafety Alert Key Table of ContentsInstaller Guide User GuideWARRANTY COVERAGE Limited Warranty Hearth & Home Technologies IncLIMITED LIFETIME WARRANTY WARRANTY PERIODThis warranty is void if WARRANTY CONDITIONSWARRANTY EXCLUSIONS LIMITATIONS OF LIABILITYB. Non-CombustibleMaterials 1Listing and Code ApprovalsA. Appliance Certification C. Combustible MaterialsA. Your Fireplace User Guide2Operating Instructions Hot glass will cause burnsD. Grate B. Seasoned WoodC. Starting a Fire E. FirescreenJ. Vented Gas Log Sets & Gas Log Lighters H. Glass DoorsI. Outside Air optional K. Optional ComponentsMoisture M. Wood FuelHardwood vs Softwood Seasoned WoodA. Disposal of Ashes 3Maintenance and ServiceB. Chimney Inspection/Cleaning Creosote - Formation and Need for RemovalD. Inspect Grate E. Glass CleaningC. Check Firebox Refractory Frequency: As desiredSolution 4Troubleshooting GuideStart Fire Problems Possible CauseA. Typical Fireplace System Installer Guide5Getting Started •Illustrations/diagrams are not drawn to scaleC. Draft B. Design and Installation ConsiderationsD. Negative Pressure E. Locating Fireplace & Chimney G. Fireplace System Requirements F. Tools and Supplies NeededH. Inspect Fireplace and Components 6Framing & Clearances A. Select Fireplace LocationB. Clearances Heatilator • CL36D, CR36D • 12538 • Rev Z 7/1239 deg C. Sidewalls/Surrounds20 in 50 degD. Frame the Fireplace B. Position the Fireplace 7Installation of FireplaceA. Things to Consider C. Place Protective Metal Hearth StripsCanada Note: Chimney air kit notshown, but required in Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12E. Install Outside Air Kit 8Chimney Assembly A. Chimney Requirements TableTable B. Using Offsets/ReturnsExample E. Install Ceiling Firestops D. Install Chimney Air KitC. Assemble Chimney Sections F. Install Attic Insulation Shield I. Install Flashing H. Complete InstallationG. Cut out Hole in Roof J. Chimney Termination Requirements 9Chase Installations A. Construct the ChaseC. Install Chase Top B. Install Fireplace & ChimneyD. Install Termination Cap •Warning! Risk of Fire! The minimum overlap of•ST375 Square Termination Cap •TR342 Round Telescoping Termination Cap•TS345/TS345P Square Termination Cap •TCT375 Terra Cotta CapA. Radiation Shield 10 ShroudsB. Field Constructed Shrouds Roofed Style Shroud radiation shield required Figure 10.4 Roofed Style Shroud DimensionsMailbox Style Shroud radiation shield required Heatilator CL36D, CR36D 12538 Rev Z 7/12B. Combustible Materials 11 FinishingA. Non-combustibleMaterials C. Hearth ExtensionD. Finishing Material Warning! Risk of FireE. Combustible Mantel MantelSidewalls/Surrounds B. Wood Burning Inserts 12 AccessoriesA. Gas Log/Lighter Provision Gas Code, ANSI Z223.113 Reference Materials A. Fireplace DimensionsB. Optional Components C. Chimney Components Catalog #14-1/2in 368 mmHeatilator • CL36D, CR36D • 12538 • Rev Z 7/12 Stocked D. Service PartsCL36D at DepotStocked D. Service Parts continuedCR36D at DepotDO NOT DISCARD THIS MANUAL – NOTES –E. Contact Information DO DISCARDNOT

Related manuals

Manual 48 pages 11.28 Kb