Fisher & Paykel MR700, MR720, MR730, MR480 technical manual

Page 19

1Plug in the 41 °C calibration probe.

2Gain access to the adjustment potentiometers VR4 and VR5, by removing the control board from the humidifier front panel.

3With the Chamber Temp button held down turn on the power switch. Display should show -1-

4Using the Chamber Temp button step through to number -4-

5Starting with a vertical bar display adjust VR4 so the display changes to an all 8 display. If VR4 is rotated too far the display becomes all horizontal bars (... thru 8.8.8. to ===). The correct point is where all the segments of the all 8 display are of equal brightness.

6Using the Chamber Temp button step to number -5-

7Remove the 41 °C calibration probe.

8Adjust VR5 for a display reading of zero. (0)

(This value may drift over time. A deviation of up to ± 2.0 will not affect circuit performance.)

9Calibration is complete; do performance check (§ 6.0)

Ref. 185040646 MR730/720/700/480 Technical Manual ¯ Revision F ¯ Issued March 2001

Image 19

Contents Auckland, New Zealand D E L S MR730 MR720 MR700 MR480National Office Revision F changes Section Description of ChangeContents Performance Check MR480 Dual Probe Temperature Test10.1 Power PCB Harness Connection DiagramMaintenance Schedule B1.1 Maintenance Schedule ChecklistAppendix D Models MR730/720/700 MR700 Series General SpecificationsRSD EOHSET TOPMR700 Series Humidifiers with Version 1.0 Software Operating Controls and ModesStandby Button MR700/720/730 only 1 MR700/MR730 ALL Software VERSIONS, MR720 Version 1.0 only 2 MR720 Version 2.0, 3.0 SoftwareAlarms and Indicators Version 3.0 Software Version 1.0 and Version 2.0 SoftwareAudio Alarm Circuit Operation Power Line Interrupt Revisions D/F Pcbs Revision H and J Pcbs For models with Revision D PCB and earlier CalibrationPage Performance Check Alarms Check MR700/720/730 Dual Probe Temperature Test Servicing Information Replacing revision F or earlier power PCB MR700/720/730Replacing revision F or earlier power PCB MR480 Fault Location SCHEMATICS, Part Lists and Mechanical Drawings Power Board Control Board Component Layout Revision F PCB Page This page Left Blank Circuit Diagrams Revision H and J PCB Control PCB Circuit Diagrams Revision H and J PCB Power PCB Circuit Diagrams Revision F PCB Control PCB Circuit Diagrams Revision F PCB Power PCB LED6,LED7 LED8,LED9,LED10 DSP1, DSP2, DSP3LED1, LED3 LED2,LED4, LED5,LED11VR4 SW5SPK1 VR1Fuse fast acting 2 a 20 × 5 mm for 230 999830009 MR480AGM Exploded Diagrams MR480 10.3 MR730/720/700 Mechanical Parts MR720ASU Exploded Diagrams MR730/720/700 Heaterplate Assembly Parts MR730/720/700/480 Page PCB Identification Diagram Power PCB Harness Connection Diagram Date Change First Serial Number Comments Affected Product Change HistoryYear Model Code Serial Number AAA XxxxxOFF Appendix aA2.3 Integral Display Error MessagesEP4 EP1EP2 EP3Second Byte First ByteThird Byte A5.4 Serial Data Interface Connector Appendix B B1 Maintenance ScheduleElectrical Safety Checks as required Photocopy and File in Maintenance RecordsPossible cause Action to take Appendix CHigh Temperature C1.6 C1.5LED on Check Voltage Rating Of Unit Appendix D Cleaning instructionsAppendix E Setup NotesDynamic Test Sequence MR730/720/700 Dynamic Test Procedure MR480