Bosch Appliances FMR-1000-RCMD Lamp Test, 3Keypad Operations, View Status, Acknowledge, Silence

Page 13

14 en OperatingRemote Command Center

9.2

Lamp Test

 

A lamp test is accomplished by pressing and holding the acknowledge [ACK] key for more

 

than 3 seconds. All LEDs on the FMR-1000-RA are turned on and the LCD display is filled with

 

black blocks when the lamp test starts. As soon as the acknowledge [ACK] key is released, the

 

revision number, Option Bus address, and key lock status appear on LCD display for

 

3 seconds. Then the LEDs and the LCD display return to normal working mode (controlled by

 

the panel).

9.3Keypad Operations

With the key lock in the locked position, the user can use the scroll keys only for navigating the LCD display and operate the acknowledge [ACK] key. Upon an invalid key press, the display shows “KEY LOCKED” for 3 seconds. Refer to Table 7.1 on Page 11 for key lock bypass option.

With either the key lock in unlocked position or the DIP switch setting for the key lock bypassed, the user may operate any of the device’s keys.

View Status

With no alarms or troubles in the system, the display message is "SYSTEM NORMAL" or "SYSTEM NORMAL DAY" along with the current date and time.

During initialization by start-up or re-configuration, the screen indicates "System Initializing”. The panel shows the “System Resetting” screen upon reset, until the system returns to the normal supervising condition.

If PAS or Pre-signal is turned on, the screen indicates “SYSTEM NORMAL DAY”.

Any off-normal conditions are shown in groups classified as fire alarm, gas alarm, supervisory and trouble.

Use the arrow keys to view events or conditions in the same group. Up and down keys move the user to the previous or next event. The left and right keys switch to other groups.

NOTICE!

For system display information, refer to FPA-1000 Installation and Operation Guide (P/N F.01U.173.607).

Acknowledge

During an alarm, pressing the acknowledge [ACK] key turns off the piezo that is sounding on an annunciator. All the ongoing events or conditions are marked as “Acknowledged”. The

24-hour trouble reminder timer starts. Any trouble event not cleared within 24 hours is sent again and the piezo begins to beep again.

If a fire input point configured as "PAS enabled" (with global PAS enabled) is activated, pressing the acknowledge [ACK] key within 15 seconds after a PAS activation starts the investigation timer. This allows the user to investigate the fire alarm or take other appropriate actions until the timer expires.

An acknowledgement operation can also be initiated by the activation of an input point configured as an acknowledge type.

Silence

Pressing the silence key performs all functions of the acknowledge operation.

When the silence operation is initiated, the panel goes into a “Silenced” status and the “Silenced" LED lights. The piezos on all keypads and annunciators turn off. All outputs are silenced if configured as “Silenceable”. NACs play the “Silenced” pulse for the programmed

F.01U.078.098 3.0 2011.11

Installation and Operation Guide

Bosch Security Systems, Inc.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Remote Command Center FMR-1000-RCMD 01U.078.098 3.0 Bosch Security Systems, Inc Table of Contents Device Description Scope of DeliveryDescription Removing the Cover Frame 4MountingSurface Mounting Flush Mounting Inserting the Language Tab on Address Setting on Wiring onOption Bus Circuit Wiring Distance 5WiringWiring Connections GNDInserting the Language Tab Removing the Cover Frame for Service8Programming 7Address SettingOption Bus DIPLEDs and LCD Keypad OperatingLED System StatusPiezo Sounder DisplayPiezo Operation System Status 3Keypad Operations Lamp TestView Status AcknowledgeSpecifications Troubleshooting11.1 Electrical 11.3 Environmental Conditions 11.2 Mechanics11.4Trademarks Índice Solución de problemas EspecificacionesCableado Suministro Incluido AvisoDescripción del Dispositivo ¡NOTAExtracción de la Cubierta de Carcasa 4MontajeMontaje en Superficie Leyenda Montaje Empotrado CableadoDistancia del cableado de los circuitos del bus de opciones Conexiones del CableadoTierra Introducción de la Ficha de Idioma Configuración de DirecciónExtracción del Marco de Cubierta de la Carcasa para el MantenimientoDirección de 8ProgramaciónBus de Opciones Teclado LCD y LED OperaciónLED Estado del SistemaSirena Piezoeléctrica PantallaOperación de la Sirena Estado del Sistema Piezoeléctrica Operaciones de Teclado Prueba de lámparasVisualización del Estado ReconocerSilencio Recordatorio de ProblemaRestablecer EvacuaciónEspecificaciones Solución de problemas11.1 Datos eléctricos Sirena Descripción Piezoeléctric11.3 Condiciones Ambientales 11.2 Datos mecánicos11.4 Marcas comerciales Cabeamento Resolução de Problemas EspecificaçõesDescrição do Dispositivo Conteúdo do FornecimentoNota CuidadoRemovendo a Estrutura de Cobertura 4InstalaçãoInstalação em Superfície Pt Instalação Centro de Comando Remoto Instalação Embutida CabeamentoDistância do Cabeamento do Circuito do Barramento de OpçõesTerra Removendo a Estrutura de Cobertura para Manutenção Definição do EndereçoEndereço do 8ProgramaçãoBarramento De Opções LEDs e Teclado LCD OperaçãoEstado do Sistema Operação Piezelétrica Estado do Sistema Sirene Piezelétrica3Operações do Teclado Teste de LâmpadaVisualizar Estado ReconhecidoLembrete de Falha Resolução de ProblemasTeste de evacuação Piezelétrica Descrição11.1 Elétricas Especificações11.2 Mecânicas SEM Comunicação11.4 Marcas Registradas 11.3 Condições AmbientaisPhillips é uma marca registrada da Phillips Screw Co Bosch Security Systems, Inc
Top Page Image Contents