Hearth and Home Technologies EL36, EL42 owner manual Non-combustible Sealant

Page 40

Non-combustible

Finishing Materials

Figure 11.5 Raised Platform Hearth Extension-Finishing Materi- als

Non-combustible Sealant

After completing the framing and applying the facing materials over the framing, a bead of non-combustible sealant must be used to close off any gaps at the top and sides between the fireplace hearth.

Non-combustible Sealant

Figure 11.6 Place Non-combustible Sealant

40	Heatilator • EL36/EL42 • 4044-132 • Rev AD • 7/12

Image 40

Contents Hot screen/mesh and glass doors will cause burns Wood Burning FireplaceFire Risk Homeowner Reference Information Listing Label Information/LocationInstaller Guide Table of ContentsUser Guide Warranty Hearth & Home Technologies Inc Limited Lifetime WarrantyWarranty Conditions This warranty is void ifListing and Code Approvals Appliance CertificationNon-Combustible Materials Combustible MaterialsYour Fireplace Operating InstructionsHot glass will cause burns Seasoned Wood Starting a FireGrate FirescreenGlass Doors Vented Gas Log Sets & Gas Log LightersOptional Components Clear SpaceWood Fuel Maintenance and Service Chimney Inspection/CleaningDisposal of Ashes Creosote Formation and Need for RemovalGlass Cleaning Check Firebox RefractoryInspect Grate Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating Fireplace & Chimney Recommended Chimney LocationsFireplace System Requirements Tools and Supplies NeededInspect Fireplace and Components Framing & Clearances Select Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplaceOutside Model #Installation of Fireplace Things to ConsiderPosition the Fireplace Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Install Outside Air Kit Outside Air InstallationChimney Assembly Chimney Requirements Chimney RequirementsUsing Offsets/Returns ExampleDegree SL306 SL312 SL318 SL324 SL336 SL348Install Chimney Air Kit Assemble Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield Prepare Attic Insulation ShieldComplete Installation Install FlashingFollowing steps should be skipped if using a chase Cut out Hole in RoofChimney Termination Requirements Multiple Chimney LocationsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap CapTS345/TS345P Square Termination Cap Shrouds Radiation ShieldField Constructed Shrouds Open Top Shroud TR342 caps require radiation shieldMailbox Style Shroud radiation shield required Roofed Style Shroud radiation shield requiredTS345 TR342 TR342/344Finishing = 1/k x inches of thickness Hearth ExtensionMinimum MaterialRaised Hearth Extension Framing Model #Non-combustible Sealant Raised Platform Hearth Extension-Finishing Materi- alsFinishing Material Decorative FacingCombustible Mantel Clearances to Mantels or other Combustibles above Fireplace4 in mm Accessories Gas Log/Lighter ProvisionWood Burning Inserts Gas Code, Ansi Z223.1Fireplace Dimensions Reference MaterialsIn. HX3 Hearth Extension 13 mm Mm HX4 Hearth ExtensionBifold Glass Doors DM1036, DM1042 AK24Chimney Components Catalog #JB877 Chimney Joint Band Ceiling FirestopCB876 Chimney Joint Band ST375 Square Termination CapCT35 Chase Top TCT375 Terra Cotta CapTS345/TS345P Square Termination Cap Part number list on following Damper Kit Air HandleStocked Service PartsAt Depot EL42 Piece RodEL42 Contact Information