Hearth and Home Technologies EL36, EL42 owner manual Install Termination Cap

Page 34

D. Install Termination Cap

Install the chimney sections up through the chase enclo- sure.

• Caulk the overlap seam of any exposed pipe sections that are located above the roof line to prevent leaks.

•Refer to termination cap instructions.

Warning! Risk of Fire! The minimum overlap of cap to pipe (as shown in the following illustrations) MUST be met or chimney may separate from cap. Separation allows sparks, heat and embers to escape.

Notice: Paint the termination cap with a rust-resistant paint to protect against the effects of corrosion on those parts exposed to the weather.

•TR344 Round Termination Cap

•TR342 Round Telescoping Termination Cap

Assemble

Termination

storm collar

Cap

around extended

 

termination cap

 

pipe

 

once cap is

 

installed.

Do NOT

 

Caulk gaps between

block air

holes

storm collar & pipe,

Storm

and storm collar

Collar

& chase top.

3 clip brackets.

 

Slip over chase collar

 

and attach with screws

 

provided.

Collar

 

2 in. (51 mm)

14 1/2 in. (368 mm)

Minimum Height

Maximum

 

Chase Top

 

Chase

Chimney

Pipe

Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)

Figure 9.5 Installing a TR342 Round Telescoping Termination

Termination

Cap

Slip

storm collar

around chimney pipe

Cap

•ST375 Square Termination Cap

before termination cap pipe is snapped into the chimney pipe.

Caulk gaps between

Storm

storm collar & pipe,

Collar

and storm collar

 

& chase top.

 

Collar

 

2 in. (51 mm)

Chimney

Minimum Height

Pipe

 

Chase Top

 

Do NOT

block air holes

6 in. (153 mm) Minimum top of chase to top of chimney pipe

Flange

Termination Cap

Collar

2 in. (51 mm)

Minimum Height

Chase Top

Place waterproof caulk or sealer under each flange of the termination cap and on top of each screw to help prevent leaks.

The last section of pipe must stop between 2 in. (51

mm)above the top of the chase and 4 3/4 in. (121

mm) below the top of the chase.

2 in. (51 mm)

maximum

4 3/4 in. (121 mm)

maximum

Chase

Chimney

Pipe

Chase

Termination cap pipe and chimney section must be snapped together to maintain an overlap of 1-1/2 in. (38 mm).

Figure 9.4 Installing a TR344 Round Termination Cap

Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)

Figure 9.6 Installing an ST375 Square Termination Cap

34

Heatilator • EL36/EL42 • 4044-132 • Rev AD • 7/12

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Hot screen/mesh and glass doors will cause burns Wood Burning FireplaceFire Risk Homeowner Reference Information Listing Label Information/LocationInstaller Guide Table of ContentsUser Guide Warranty Hearth & Home Technologies Inc Limited Lifetime WarrantyWarranty Conditions This warranty is void ifNon-Combustible Materials Listing and Code ApprovalsAppliance Certification Combustible MaterialsYour Fireplace Operating InstructionsHot glass will cause burns Grate Seasoned WoodStarting a Fire FirescreenOptional Components Glass DoorsVented Gas Log Sets & Gas Log Lighters Clear SpaceWood Fuel Disposal of Ashes Maintenance and ServiceChimney Inspection/Cleaning Creosote Formation and Need for RemovalInspect Grate Glass CleaningCheck Firebox Refractory Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating Fireplace & Chimney Recommended Chimney LocationsFireplace System Requirements Tools and Supplies NeededInspect Fireplace and Components Framing & Clearances Select Fireplace LocationClearances Clearances to Combustible MaterialsOutside Sidewalls/SurroundsFrame the Fireplace Model #Position the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Install Outside Air Kit Outside Air InstallationChimney Assembly Chimney Requirements Chimney RequirementsDegree Using Offsets/ReturnsExample SL306 SL312 SL318 SL324 SL336 SL348Install Chimney Air Kit Assemble Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield Prepare Attic Insulation ShieldFollowing steps should be skipped if using a chase Complete InstallationInstall Flashing Cut out Hole in RoofChimney Termination Requirements Multiple Chimney LocationsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap CapTS345/TS345P Square Termination Cap Field Constructed Shrouds ShroudsRadiation Shield Open Top Shroud TR342 caps require radiation shieldTS345 TR342 Mailbox Style Shroud radiation shield requiredRoofed Style Shroud radiation shield required TR342/344Minimum Finishing= 1/k x inches of thickness Hearth Extension MaterialRaised Hearth Extension Framing Model #Non-combustible Sealant Raised Platform Hearth Extension-Finishing Materi- alsFinishing Material Decorative FacingCombustible Mantel Clearances to Mantels or other Combustibles above Fireplace4 in mm Wood Burning Inserts AccessoriesGas Log/Lighter Provision Gas Code, Ansi Z223.1Fireplace Dimensions Reference MaterialsBifold Glass Doors DM1036, DM1042 In. HX3 Hearth Extension 13 mmMm HX4 Hearth Extension AK24Chimney Components Catalog #CB876 Chimney Joint Band JB877 Chimney Joint BandCeiling Firestop ST375 Square Termination CapCT35 Chase Top TCT375 Terra Cotta CapTS345/TS345P Square Termination Cap Part number list on following Damper Kit Air HandleStocked Service PartsAt Depot EL42 Piece RodEL42 Contact Information
Top Page Image Contents