Hearth and Home Technologies EXCLAIM-36 Assemble Chimney Sections, Install Chimney Air Kit

Page 29

C. Assemble Chimney Sections

WARNING! Risk of Fire! DO NOT install substitute or damaged chimney components.

•Use only those components described in this manual.

Substitute or damaged chimney components could impair safe operation and cause overheating and ﬁre.

•Support the pipe during construction and check to be sure inadvertent loading has not dislodged the chimney section from the ﬁreplace or at any chimney joint.

•Attach a straight chimney section or an offset to the top of the ﬁreplace.

•Place inner ﬂue to the inside of the chimney section below it. Place the outer casing outside the outer casing of the chimney section below it. Refer to Figure 8.4.

NOTICE: Chimney sections cannot be disassembled once locked together. Plan ahead!

•Lock chimney sections and/or offsets/returns together by pushing downward until the top section meets the stop bead on the lower section.

•Pull on the top section to make sure it is fully engaged and will not separate.

•You may use #6 or #8 sheet metal screws no longer than 1/2 in. (13 mm) to fasten chimney sections together. Do NOT penetrate inner ﬂue.

WARNING! Risk of Fire! You MUST use screws (pro- vided) to fasten offset/returns to chimney sections to keep the chimney parts from twisting. Failure to do so could cause ﬁre.

•Fasten offset/returns to chimney sections. Insert the screws (provided) through the predrilled holes. Do NOT penetrate inner ﬂue.

•Secure chimney returns with hanger straps provided; fasten to studs or joists.

•Vertical straight runs of chimney must be supported every 35 ft (10.7 m).

D. Install Chimney Air Kit

•Required in Canada.

•Follow instructions provided with this accessory.

Figure 8.4 Assembling Chimney Sections

Heat & Glo • EXCLAIM-36, EXCLAIM-42 • 4013-251 Rev C • 11/08

29

Image 29

Contents Fire Risk Wood Burning FireplaceHot screen/mesh and glass doors will cause burns Number Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyHeat & Glo EXCLAIM-36, EXCLAIM-42 4013-251 Rev C 11/08 Appliance Certiﬁcation Listing and Code ApprovalsNon-Combustible Materials Combustible MaterialsHot glass will cause burns Operating InstructionsYour Fireplace Starting a Fire Seasoned WoodGrate FirescreenVented Gas Log Sets & Gas Log Lighters Glass DoorsOptional Components Clear SpaceWood Fuel Chimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Creosote Formation and Need for RemovalCheck Firebox Refractory Glass CleaningInspect Grate Frequency As desiredStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedNegative Pressure Design and Installation ConsiderationsDraft Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyInspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Select Fireplace Location Framing & ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsUnpack the Fireplace EXCLAIM-42 only Installation of FireplaceThings to Consider Unpack the Fireplace EXCLAIM-36 onlyRemoving Smoke Shield Position the Fireplace EXCLAIM-42 onlyGAS Knockout Install the Refractory EXCLAIM-42 onlyLevel Fireplace Place Protective Metal Hearth StripsYES Install Outside Air KitChimney Assembly Height of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssemble Chimney Sections Install Chimney Air KitInstalling the Ceiling Firestop Install Ceiling Firestops330 mm Install Attic Insulation ShieldInstall Flashing Complete InstallationFollowing steps should be skipped if using a chase Cut out Hole in RoofFlat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST1175/ST475 Square Termination Cap Install Termination CapTCT1175 Terra Cotta Cap Radiation Shield ShroudsField Constructed Shrouds Open Top Shroud TR11/TR11T caps require radiation shieldRoofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield required= 1/k x inches of thickness FinishingHearth Extension Hearth Extension Construction Raised Hearth Extension FramingFlush Hearth Extension Framing Non-combustible SealantNoncombustible Facing Finishing MaterialCombustible Mantel 19 3/4 502 mm Gas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1Reference Materials Fireplace DimensionsEXCLAIM-36 EXCLAIM-42 Catalog # Chimney Components15-1/4 387 mm 15-3/4 400 mm CT56 Chase Top LDS33/LDS46 Decorative Shroud EXCLAIM-36H, EXCLAIM-36T Service PartsEXCLAIM-42H, EXCLAIM-42T This page intentionally left blank Do not Discard this Manual