Hearth and Home Technologies 5100I-GD-B, 5100I-NL-B warranty Blower Cord Location

Page 12

R

5100-I ACT WOOD INSERT

E. Blower Cord Location

The 5100-I Insert comes standard with 2 blowers, installed at the factory with the power cord on right side of insert (as you face the unit). Do not route the power cord under or in front of appliance.

The power cord can also be installed on the left side. Follow instructions below.

Green grounding wire

White wire into Red Connector

 

Black wire into Blue Connector

 

Left Blower

 

Snap Disc

Right Blower

 

Red

 

Connector

Snap Disc

Blue

by-pass

Connector

switch

 

Speed Control

 

(Rheostat)

Figure 12.1 - Blower Assembly Components

1.Disconnect the appliance from power supply.

2.Remove the grille following instructions on page 11.

3.Unplug the blower cord wires from the wire harness.

4.Remove green grounding wire from grounding screw.

5.Using a pair of pliers, squeeze the strain relief and remove the blower cord wires and strain relief from the grille.

6.Locate the wire harness wires tucked up under the ash- catcher on the left side of the appliance. Cut the zip tie that is holding the wires in place.

7.Remove the button plug from the left side of grille. Thread the blower cords wires through the hole and snap the strain relief in place. Figure 12.3.

8.Attach grounding wire to ground screw.

9.Connect the white blower cord wire to the red connector on the wire harness.

10.Connect the black blower cord wire to the blue connec- tor on the wire harness.

11.Tuck the wire out of the way of the blower motor.

12.Re-install grille.

NOTE: Each wire has a label to denote which component it connects to.

 

 

 

 

Blower cord attached to

 

 

 

 

right side of grille.

 

 

 

 

Strain Relief

Bottom

ofgrille

Blower cord

 

 

 

 

 

 

 

 

Green

 

 

 

 

grounding wire

 

 

 

 

White wire

 

 

 

 

Grounding

 

 

of

grille

screw

Top

Black wire

 

 

 

 

 

 

 

Back view of grille

Figure 12.2

 

Remove button plug

grille

 

of

 

Bottom

 

grille

Grounding screw

 

of

 

Top

Back view of left

 

 

side of grille

Figure 12.3

Caution

Shock hazard.

• Do NOT remove grounding prong from plug.

•Plug directly into properly grounded 3 prong receptacle.

•Route cord away from appliance.

•Do NOT route cord under or in front of appli- ance.

Page 12

438-0380D

September 1, 2008

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Advanced Combustion Technology ACT Hot glass will cause burnsLocation On right side of insert as face the appliance Serial NumberModel Name Manufactured DateTable of Contents Mobile Home Approved BTU & Efficiency Specifications Glass Specifications1Listing and Code Approvals Appliance CertificationFire Safety Design, Installation & Location ConsiderationsGetting Started Negative Pressure Flue Draft Considerations Tools And Supplies NeededInspect Appliance and Components 3Dimensions and Clearances Appliance DimensionsPanel Size Installation Masonry, Heat Circulating and *Zero Clearance Clearance to CombustiblesSideWall With 8 Mantel Deflector, Part NoInstallation Considerations Floor Protection USA & CanadaHearth Extension Calculating Alternate Floor Protection MaterialOutside Air Installation Disconnect the appliance from power supply Blower Cord LocationWiring Diagram Optional Offset AdapterChimney Requirements Venting ComponentsChimney Systems Installing Chimney Components Ovalizing Round Stainless Steel LinersAir Clearances Chimney Termination Requirements Masonry Fireplace USA Installations only Factory-Built Zero Clearance Fireplace6Mobile Home Installation Requirements for outside combustion air supply toInstallation Outline Panel & Trim Set Installation Appliance Set-upLeveling Bolts Securing Liner to Flue Collar Assembling TrimZero Clearance Adjustable Trim Support Size 12 d x 50 w, 2-10 hIncluded in Kit Tools Needed 22.28Operating Instructions Over-Firing Your ApplianceWood Selection & Storage Burning ProcessAir Controls Second StageFinal Stage Start-Up SystemHeat Output Burn RatesBuilding a Fire Opacity Smoke Blower Operating InstructionsFrequently Asked Questions Issues SolutionsGeneral Maintenance Creosote Chimney CleaningGlass Cleaning Maintaining & Servicing Your ApplianceGlass Replacement Door Assembly Cleaning Plated SurfacesFrequency As needed Slide Window In / Out Loosen Remove Bolts Firebrick Replacement Nbr Brick Size QtyBlower Replacement Baffle RemovalCorrect Baffle & Blanket Placement Incorrect PositionsTroubleshooting Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Reference Materials Exploded ViewsBeginning Manufactured Date November 1 Service Parts & Accessories BRICK-438Accessories Service And Maintenance Log Date of Service Performed By Description of ServiceService And Maintenance Log Cont’d Homeowner’s Notes Warranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Contact Information Dealer Telephone

5100I-NL-B, 5100I-GD-B specifications

Hearth and Home Technologies has established itself as a leader in the home heating industry, offering a wide range of high-quality fireplaces. Among their standout products are the 5100I-GD-B and 5100I-NL-B models. These two direct vent gas fireplaces not only enhance the aesthetics of a home but also provide efficient heating solutions.

The 5100I-GD-B model boasts a contemporary design that fits well in modern interiors. Equipped with a glass front, it allows for an unobstructed view of the flames, creating a cozy atmosphere in any space. The unit's high-efficiency burner maximizes heat output while minimizing gas consumption, making it an eco-friendly choice for homeowners. Additionally, the electronic ignition system ensures reliable startups, while the integrated control panel offers easy adjustments for flame height and heat settings.

On the other hand, the 5100I-NL-B model presents a more traditional design, featuring a clean face that blends seamlessly with various décor styles. Like its counterpart, this model is also engineered for efficiency, offering an impressive Annual Fuel Utilization Efficiency (AFUE) rating. This makes it an excellent choice for those looking to reduce energy costs without sacrificing comfort. The 5100I-NL-B is also equipped with an advanced combustion system that ensures complete fuel combustion, resulting in fewer emissions and a cleaner burn.

Both models feature optional accessories, including decorative media options like logs or stones, allowing homeowners to customize the look of their fireplaces. The direct vent system allows for easy installation in various locations, as it vents gases directly outside, ensuring indoor air quality is maintained.

Safety is a priority with Hearth and Home Technologies, and both models come with a safety screen and an automatic shut-off feature. This ensures peace of mind while enjoying the warmth and ambiance these fireplaces provide.

Overall, the Hearth and Home Technologies 5100I-GD-B and 5100I-NL-B gas fireplaces exemplify the perfect blend of functionality and style, making them ideal choices for anyone looking to enhance their home's heating options. With their impressive features and efficient performance, these models are designed to keep homes warm and inviting while offering options to match personal tastes.
Top Page Image Contents