Hearth and Home Technologies 5100I-NL-B, 5100I-GD-B warranty Masonry Fireplace

Page 17

5100-I ACT WOOD INSERT

F. Masonry Fireplace

R

The Quadra-Fire 5100-I Insert conforms with the UL 1482 and ULC S628 (Canada) in all respects, and is approved to UL & ULC safety standards for installation and use within a fireplace with a masonry chimney in accordance with NFPA 211.

In the USA all masonry fireplace installations require a stain- less steel liner connector pipe extending to the first flue liner of the existing code approved masonry chimney. In Canada, a full reline is required.

NOTE: Installation into fireplaces without a permit will void the listing.

NOTE: In Canada, the chimney liner must conform to the Class 3 requirements of CAN/ULC-S635, Standard for Lining Systems for Existing Masonry or Factory-Built Chimneys and Vents, or CAN/ULC-S640, Standard for Lining Systems for New Masonry Chimneys.

UL 1777 Insulated Stainless Steel Liner or Other Approved Lining System

Follow Manufacturer’s Instructions on Insulation and Support

For Zero or Other Non-Code Clearances, Follow Approved Liner Manufacturer’s Specific Insulation Requirements: Different Clearances May Require Different Specifications

Masonry Chimney Must

Have Structural Integrity

UL 1777 Insulated Stainless Steel

Liner or Other Approved Lining System

Minimum 8 in. (203mm) Masonry

Thickness in Front of Smoke Chamber

Minimum Clearance in Accordance with Insert Listing

Floor Protection in

Accordance with Insert

Listing

Combustible Floor

Follow Manufacturer’s

Instructions for Maximum

Liner Extension Above

Chimney

Maximum 30 Degrees

Offset in Chimney

Damper Plate Removed or

Fastened in Open Position

Seal with Non-Combustible Material

Figure 17.1

September 1, 2008

438-0380D

Page 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Hot glass will cause burns Advanced Combustion Technology ACTSerial Number Location On right side of insert as face the applianceModel Name Manufactured DateTable of Contents Glass Specifications Mobile Home Approved BTU & Efficiency Specifications1Listing and Code Approvals Appliance CertificationGetting Started Fire SafetyDesign, Installation & Location Considerations Negative Pressure Inspect Appliance and Components Flue Draft ConsiderationsTools And Supplies Needed Panel Size 3Dimensions and ClearancesAppliance Dimensions Clearance to Combustibles Installation Masonry, Heat Circulating and *Zero ClearanceSideWall With 8 Mantel Deflector, Part NoFloor Protection USA & Canada Installation ConsiderationsHearth Extension Calculating Alternate Floor Protection MaterialOutside Air Installation Blower Cord Location Disconnect the appliance from power supplyOptional Offset Adapter Wiring DiagramChimney Systems Chimney RequirementsVenting Components Air Clearances Installing Chimney ComponentsOvalizing Round Stainless Steel Liners Chimney Termination Requirements Masonry Fireplace Factory-Built Zero Clearance Fireplace USA Installations onlyRequirements for outside combustion air supply to 6Mobile Home InstallationLeveling Bolts Installation Outline Panel & Trim Set InstallationAppliance Set-up Assembling Trim Securing Liner to Flue CollarSize 12 d x 50 w, 2-10 h Zero Clearance Adjustable Trim SupportIncluded in Kit Tools Needed 22.2Over-Firing Your Appliance 8Operating InstructionsWood Selection & Storage Burning ProcessSecond Stage Air ControlsFinal Stage Start-Up SystemBuilding a Fire Heat OutputBurn Rates Blower Operating Instructions Opacity SmokeIssues Solutions Frequently Asked QuestionsCreosote Chimney Cleaning General MaintenanceGlass Cleaning Maintaining & Servicing Your ApplianceFrequency As needed Glass Replacement Door AssemblyCleaning Plated Surfaces Slide Window In / Out Loosen Remove Bolts Nbr Brick Size Qty Firebrick ReplacementBaffle Removal Blower ReplacementIncorrect Positions Correct Baffle & Blanket PlacementDiagnostic Question Possible Causes of Condition Solutions TroubleshootingDon’t get enough/any heat. What can I do about it? Beginning Manufactured Date November 1 Reference MaterialsExploded Views BRICK-438 Service Parts & AccessoriesAccessories Date of Service Performed By Description of Service Service And Maintenance LogService And Maintenance Log Cont’d Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability Warranty Policy Hearth & Home Technologies Limited WarrantyHearth & Home Technologies Limited Warranty Cont’d Dealer Telephone Contact Information

5100I-NL-B, 5100I-GD-B specifications

Hearth and Home Technologies has established itself as a leader in the home heating industry, offering a wide range of high-quality fireplaces. Among their standout products are the 5100I-GD-B and 5100I-NL-B models. These two direct vent gas fireplaces not only enhance the aesthetics of a home but also provide efficient heating solutions.

The 5100I-GD-B model boasts a contemporary design that fits well in modern interiors. Equipped with a glass front, it allows for an unobstructed view of the flames, creating a cozy atmosphere in any space. The unit's high-efficiency burner maximizes heat output while minimizing gas consumption, making it an eco-friendly choice for homeowners. Additionally, the electronic ignition system ensures reliable startups, while the integrated control panel offers easy adjustments for flame height and heat settings.

On the other hand, the 5100I-NL-B model presents a more traditional design, featuring a clean face that blends seamlessly with various décor styles. Like its counterpart, this model is also engineered for efficiency, offering an impressive Annual Fuel Utilization Efficiency (AFUE) rating. This makes it an excellent choice for those looking to reduce energy costs without sacrificing comfort. The 5100I-NL-B is also equipped with an advanced combustion system that ensures complete fuel combustion, resulting in fewer emissions and a cleaner burn.

Both models feature optional accessories, including decorative media options like logs or stones, allowing homeowners to customize the look of their fireplaces. The direct vent system allows for easy installation in various locations, as it vents gases directly outside, ensuring indoor air quality is maintained.

Safety is a priority with Hearth and Home Technologies, and both models come with a safety screen and an automatic shut-off feature. This ensures peace of mind while enjoying the warmth and ambiance these fireplaces provide.

Overall, the Hearth and Home Technologies 5100I-GD-B and 5100I-NL-B gas fireplaces exemplify the perfect blend of functionality and style, making them ideal choices for anyone looking to enhance their home's heating options. With their impressive features and efficient performance, these models are designed to keep homes warm and inviting while offering options to match personal tastes.
Top Page Image Contents