Hearth and Home Technologies 5100I-NL-B warranty Securing Liner to Flue Collar, Assembling Trim

Page 21

5100-I ACT WOOD INSERT

R

2.Assembling Trim

a.Place protective covering on surface to be used to assemble the trim pieces. Lay the trim face down.

b.Attach the 2 side trim pieces to the top trim at each corner using the “L” bracket included in fasteners package. Slide assembled trim over panel set.

Figure 21.1.

NOTE: If you have a mantel, you may need to install the trim on your panels before you push the insert into the fireplace opening. If not, you can slide the trim over the panel set after the insert is in its final position.

D. Securing Liner to Flue Collar

There are two options to secure the liner to the chimney ring:

Option One: If there is enough room on the top of the insert to work, hand bend the 2 tabs upward 90°. Secure the liner with the supplied hex head bolts 1/4-20-3/4.

Option Two: Remove the manifold tubes, fiberboard baffle and ceramic blanket. From inside the firebox, pull liner down through the chimney ring below the outer skin. There are 2 pre-drilled holes in the chimney ring 180° apart. Secure the liner with the supplied hex head bolts 1/4-20-3/4. See Fig- ures 32.3 and 32.4 on page 32 for details for removing the manifold tubes, baffle and ceramic blanket.

View of “L” bracket installed

2 pre-drilled holes on flue collar under outer skin (access through firebox)

Figure 21.1

Attach liner with 2 tabs

Figure 22.2

NOTE: Tabs are shipped from factory in a flat position. Bend upwards 90 degrees as show in Figure 22.2

September 1, 2008

438-0380D

Page 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Hot glass will cause burns Advanced Combustion Technology ACTSerial Number Location On right side of insert as face the applianceModel Name Manufactured DateTable of Contents Glass Specifications Mobile Home Approved BTU & Efficiency Specifications1Listing and Code Approvals Appliance CertificationFire Safety Design, Installation & Location ConsiderationsGetting Started Negative Pressure Flue Draft Considerations Tools And Supplies NeededInspect Appliance and Components 3Dimensions and Clearances Appliance DimensionsPanel Size Clearance to Combustibles Installation Masonry, Heat Circulating and *Zero ClearanceSideWall With 8 Mantel Deflector, Part NoFloor Protection USA & Canada Installation ConsiderationsHearth Extension Calculating Alternate Floor Protection MaterialOutside Air Installation Blower Cord Location Disconnect the appliance from power supplyOptional Offset Adapter Wiring DiagramChimney Requirements Venting ComponentsChimney Systems Installing Chimney Components Ovalizing Round Stainless Steel LinersAir Clearances Chimney Termination Requirements Masonry Fireplace Factory-Built Zero Clearance Fireplace USA Installations onlyRequirements for outside combustion air supply to 6Mobile Home InstallationInstallation Outline Panel & Trim Set Installation Appliance Set-upLeveling Bolts Assembling Trim Securing Liner to Flue CollarSize 12 d x 50 w, 2-10 h Zero Clearance Adjustable Trim SupportIncluded in Kit Tools Needed 22.2Over-Firing Your Appliance 8Operating InstructionsWood Selection & Storage Burning ProcessSecond Stage Air ControlsFinal Stage Start-Up SystemHeat Output Burn RatesBuilding a Fire Blower Operating Instructions Opacity SmokeIssues Solutions Frequently Asked QuestionsCreosote Chimney Cleaning General MaintenanceGlass Cleaning Maintaining & Servicing Your ApplianceGlass Replacement Door Assembly Cleaning Plated SurfacesFrequency As needed Slide Window In / Out Loosen Remove Bolts Nbr Brick Size Qty Firebrick ReplacementBaffle Removal Blower ReplacementIncorrect Positions Correct Baffle & Blanket PlacementDiagnostic Question Possible Causes of Condition Solutions TroubleshootingDon’t get enough/any heat. What can I do about it? Reference Materials Exploded ViewsBeginning Manufactured Date November 1 BRICK-438 Service Parts & AccessoriesAccessories Date of Service Performed By Description of Service Service And Maintenance LogService And Maintenance Log Cont’d Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability Warranty Policy Hearth & Home Technologies Limited WarrantyHearth & Home Technologies Limited Warranty Cont’d Dealer Telephone Contact Information

5100I-NL-B, 5100I-GD-B specifications

Hearth and Home Technologies has established itself as a leader in the home heating industry, offering a wide range of high-quality fireplaces. Among their standout products are the 5100I-GD-B and 5100I-NL-B models. These two direct vent gas fireplaces not only enhance the aesthetics of a home but also provide efficient heating solutions.

The 5100I-GD-B model boasts a contemporary design that fits well in modern interiors. Equipped with a glass front, it allows for an unobstructed view of the flames, creating a cozy atmosphere in any space. The unit's high-efficiency burner maximizes heat output while minimizing gas consumption, making it an eco-friendly choice for homeowners. Additionally, the electronic ignition system ensures reliable startups, while the integrated control panel offers easy adjustments for flame height and heat settings.

On the other hand, the 5100I-NL-B model presents a more traditional design, featuring a clean face that blends seamlessly with various décor styles. Like its counterpart, this model is also engineered for efficiency, offering an impressive Annual Fuel Utilization Efficiency (AFUE) rating. This makes it an excellent choice for those looking to reduce energy costs without sacrificing comfort. The 5100I-NL-B is also equipped with an advanced combustion system that ensures complete fuel combustion, resulting in fewer emissions and a cleaner burn.

Both models feature optional accessories, including decorative media options like logs or stones, allowing homeowners to customize the look of their fireplaces. The direct vent system allows for easy installation in various locations, as it vents gases directly outside, ensuring indoor air quality is maintained.

Safety is a priority with Hearth and Home Technologies, and both models come with a safety screen and an automatic shut-off feature. This ensures peace of mind while enjoying the warmth and ambiance these fireplaces provide.

Overall, the Hearth and Home Technologies 5100I-GD-B and 5100I-NL-B gas fireplaces exemplify the perfect blend of functionality and style, making them ideal choices for anyone looking to enhance their home's heating options. With their impressive features and efficient performance, these models are designed to keep homes warm and inviting while offering options to match personal tastes.
Top Page Image Contents