Hearth and Home Technologies 5100I-GD-B, 5100I-NL-B Zero Clearance Adjustable Trim Support, 22.2

Page 22

R

5100-I ACT WOOD INSERT

E.Zero Clearance Adjustable Trim Support

Size: 12” d x 50” w, 2-10” h

Included in Kit:

Tools Needed:

(1) Trim top

Phillips head screwdriver

(1)

Trim front

Sheet metal shears

(2)

Trim sides

Measuring tape

Double-sided tape

Gloves

(already installed)

1.The 10 screws on each set of scissors will already be loose when shipped. Figure 22.1.

2.Expand scissors to desired height. Tighten screws to hold in place using Phillips Head screwdriver. Figure

22.2.

3.Measure front and side trims to required height to cover scissors and mark pieces for cutting. Cut excess mate- rial from top of trim’s edge, not bottom. This edge will be sharp; wear gloves to prevent injury to your hands.

Figure 22.2.

4.Using sheet metal shears, cut trim along the marked edge. The cut edge fits under lip of top trim, so it allows for some variance in your straight edge.

5.The double-sided tape that holds front and side trims to scissors has a particularly powerful bonding adhesive.

Adjustments are extremely difficult once trim has adhered to tape. Do a dry run first without removing paper from tape.

6.Place cut edge of trim under top lip and into position on scissors. Place side pieces on first and then front piece.

The front piece overlaps side pieces.

7.Once you are satisfied with the positioning, remove trim and set aside.

8.Remove the paper from double-sided tape that is to accept trim side. Align side and then press hard against tape to secure side piece. Repeat for other side. Install front trim piece last.

NOTE: 3/8 inch (9.5mm) thick tile or like material can be cut to size and fit under lip of top trim edge for a decorative touch.

Figure 22.3.

CAUTION

Sharp Edges

• Wear protective gloves during installation.

EXPLODED VIEW OF SCISSORS

 

SCREWS ARE CIRCLED

DOUBLE-SIDED TAPE

DOUBLE-SIDED TAPE

Figure 22.1

EXPAND SCISSORS TO DESIRED HEIGHT

 

 

CUT TOP EDGE OF TRIM,

INSTALL FRONT TRIM LAST.

NOT BOTTOM EDGE

CORNERS OVERLAP SIDE

 

TRIM PIECES

 

Figure 22.2

Decorative tile may

be installed

Figure 22.3

Figure 22.4

Page 22

438-0380D

September 1, 2008

Image 22
Contents Advanced Combustion Technology ACT Hot glass will cause burnsModel Name Location On right side of insert as face the applianceSerial Number Manufactured DateTable of Contents 1Listing and Code Approvals Mobile Home Approved BTU & Efficiency SpecificationsGlass Specifications Appliance CertificationDesign, Installation & Location Considerations Fire SafetyGetting Started Negative Pressure Tools And Supplies Needed Flue Draft ConsiderationsInspect Appliance and Components Appliance Dimensions 3Dimensions and ClearancesPanel Size SideWall Installation Masonry, Heat Circulating and *Zero ClearanceClearance to Combustibles With 8 Mantel Deflector, Part NoHearth Extension Installation ConsiderationsFloor Protection USA & Canada Calculating Alternate Floor Protection MaterialOutside Air Installation Disconnect the appliance from power supply Blower Cord LocationWiring Diagram Optional Offset AdapterVenting Components Chimney RequirementsChimney Systems Ovalizing Round Stainless Steel Liners Installing Chimney ComponentsAir Clearances Chimney Termination Requirements Masonry Fireplace USA Installations only Factory-Built Zero Clearance Fireplace6Mobile Home Installation Requirements for outside combustion air supply toAppliance Set-up Installation Outline Panel & Trim Set InstallationLeveling Bolts Securing Liner to Flue Collar Assembling TrimIncluded in Kit Tools Needed Zero Clearance Adjustable Trim SupportSize 12 d x 50 w, 2-10 h 22.2Wood Selection & Storage 8Operating InstructionsOver-Firing Your Appliance Burning ProcessFinal Stage Air ControlsSecond Stage Start-Up SystemBurn Rates Heat OutputBuilding a Fire Opacity Smoke Blower Operating InstructionsFrequently Asked Questions Issues SolutionsGlass Cleaning General MaintenanceCreosote Chimney Cleaning Maintaining & Servicing Your ApplianceCleaning Plated Surfaces Glass Replacement Door AssemblyFrequency As needed Slide Window In / Out Loosen Remove Bolts Firebrick Replacement Nbr Brick Size QtyBlower Replacement Baffle RemovalCorrect Baffle & Blanket Placement Incorrect PositionsTroubleshooting Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Exploded Views Reference MaterialsBeginning Manufactured Date November 1 Service Parts & Accessories BRICK-438Accessories Service And Maintenance Log Date of Service Performed By Description of ServiceService And Maintenance Log Cont’d Homeowner’s Notes Warranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Contact Information Dealer Telephone

5100I-NL-B, 5100I-GD-B specifications

Hearth and Home Technologies has established itself as a leader in the home heating industry, offering a wide range of high-quality fireplaces. Among their standout products are the 5100I-GD-B and 5100I-NL-B models. These two direct vent gas fireplaces not only enhance the aesthetics of a home but also provide efficient heating solutions.

The 5100I-GD-B model boasts a contemporary design that fits well in modern interiors. Equipped with a glass front, it allows for an unobstructed view of the flames, creating a cozy atmosphere in any space. The unit's high-efficiency burner maximizes heat output while minimizing gas consumption, making it an eco-friendly choice for homeowners. Additionally, the electronic ignition system ensures reliable startups, while the integrated control panel offers easy adjustments for flame height and heat settings.

On the other hand, the 5100I-NL-B model presents a more traditional design, featuring a clean face that blends seamlessly with various décor styles. Like its counterpart, this model is also engineered for efficiency, offering an impressive Annual Fuel Utilization Efficiency (AFUE) rating. This makes it an excellent choice for those looking to reduce energy costs without sacrificing comfort. The 5100I-NL-B is also equipped with an advanced combustion system that ensures complete fuel combustion, resulting in fewer emissions and a cleaner burn.

Both models feature optional accessories, including decorative media options like logs or stones, allowing homeowners to customize the look of their fireplaces. The direct vent system allows for easy installation in various locations, as it vents gases directly outside, ensuring indoor air quality is maintained.

Safety is a priority with Hearth and Home Technologies, and both models come with a safety screen and an automatic shut-off feature. This ensures peace of mind while enjoying the warmth and ambiance these fireplaces provide.

Overall, the Hearth and Home Technologies 5100I-GD-B and 5100I-NL-B gas fireplaces exemplify the perfect blend of functionality and style, making them ideal choices for anyone looking to enhance their home's heating options. With their impressive features and efficient performance, these models are designed to keep homes warm and inviting while offering options to match personal tastes.