Hearth and Home Technologies 5100I-NL-B, 5100I-GD-B warranty 6Mobile Home Installation

Page 19

5100-I ACT WOOD INSERT

6Mobile Home Installation

R

1.

An outside air inlet must be provided for combustion

 

See page 11 for detailed information.

2.

Appliance must be secured to the mobile home structure.

 

Drill a hole on each side of the insert into the outer

 

skin and into the floor. Use plumbers tape to secure to

 

structure (washers may be required).

3.

Appliance must be grounded with #8 solid copper

 

grounding wire or equivalent and terminated at each

Spark Arestor Cap

Storm Collar

Roof Flashing

 

end with N.E.C. approved grounding device.

4.

The factory-built fireplace must meet (UM)84-HUD

 

requirements for outside combustion air supply to the

 

fireplace fire chamber and the chimney must be listed to

 

UL103 HT or a listed UL 1777 full length 6 inch (152mm)

 

diameter liner must be used. It must be equipped with a

 

spark arrestor cap and the outside air must be installed

 

on the insert.

5.

In Canada, this appliance must be connected to a

Joist Shield/Firestop

Figure 19.1

Listed StaInless Steel Liner

 

6 inch (152mm) factory-built chimney conforming to

 

CAN/ULC-S610, STANDARD FOR FACTORY BUILT

 

CHIMNEYS.

6.

Follow the chimney and chimney connector

 

manufacturer’s instructions when installing the flue

 

system for use in a mobile home.

7.

Maintain clearance to combustibles.

8.

Floor protection requirements must be followed

 

precisely.

9.

Use silicone to create an effective vapor barrier at

 

the location where the chimney or other component

 

penetrates to the exterior of the structure.

10. Burn wood only. Other types of fuels may generate

 

poisonous gases (e.g., carbon monoxide).

11. If unit burns poorly while an exhaust blower is on in

 

home, (i.e., range hood), increase combustion air.

NOTE: Top sections of chimney must be removable to allow maximum clearance of 13.5 feet (411cm) from ground level for transportation purposes.

CAUTION

Maintain structural integrity of mobile home:

Floor, wall, ceiling and/or roof.

Do NOT cut through:

Floor joist, wall, studs or ceiling trusses.

Any supporting material that would affect the structural integrity.

WARNING

Asphyxiation Risk.

Never install in a sleeping room.

Consumes oxygen in the room

September 1, 2008

438-0380D

Page 19

Image 19
Contents Hot glass will cause burns Advanced Combustion Technology ACTManufactured Date Location On right side of insert as face the applianceSerial Number Model NameTable of Contents Appliance Certification Mobile Home Approved BTU & Efficiency SpecificationsGlass Specifications 1Listing and Code ApprovalsDesign, Installation & Location Considerations Fire SafetyGetting Started Negative Pressure Tools And Supplies Needed Flue Draft ConsiderationsInspect Appliance and Components Appliance Dimensions 3Dimensions and ClearancesPanel Size With 8 Mantel Deflector, Part No Installation Masonry, Heat Circulating and *Zero ClearanceClearance to Combustibles SideWallCalculating Alternate Floor Protection Material Installation ConsiderationsFloor Protection USA & Canada Hearth ExtensionOutside Air Installation Blower Cord Location Disconnect the appliance from power supplyOptional Offset Adapter Wiring DiagramVenting Components Chimney RequirementsChimney Systems Ovalizing Round Stainless Steel Liners Installing Chimney ComponentsAir Clearances Chimney Termination Requirements Masonry Fireplace Factory-Built Zero Clearance Fireplace USA Installations onlyRequirements for outside combustion air supply to 6Mobile Home InstallationAppliance Set-up Installation Outline Panel & Trim Set InstallationLeveling Bolts Assembling Trim Securing Liner to Flue Collar22.2 Zero Clearance Adjustable Trim SupportSize 12 d x 50 w, 2-10 h Included in Kit Tools NeededBurning Process 8Operating InstructionsOver-Firing Your Appliance Wood Selection & StorageStart-Up System Air ControlsSecond Stage Final StageBurn Rates Heat OutputBuilding a Fire Blower Operating Instructions Opacity SmokeIssues Solutions Frequently Asked QuestionsMaintaining & Servicing Your Appliance General MaintenanceCreosote Chimney Cleaning Glass CleaningCleaning Plated Surfaces Glass Replacement Door AssemblyFrequency As needed Slide Window In / Out Loosen Remove Bolts Nbr Brick Size Qty Firebrick ReplacementBaffle Removal Blower ReplacementIncorrect Positions Correct Baffle & Blanket PlacementDiagnostic Question Possible Causes of Condition Solutions TroubleshootingDon’t get enough/any heat. What can I do about it? Exploded Views Reference MaterialsBeginning Manufactured Date November 1 BRICK-438 Service Parts & AccessoriesAccessories Date of Service Performed By Description of Service Service And Maintenance LogService And Maintenance Log Cont’d Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability Warranty Policy Hearth & Home Technologies Limited WarrantyHearth & Home Technologies Limited Warranty Cont’d Dealer Telephone Contact Information

5100I-NL-B, 5100I-GD-B specifications

Hearth and Home Technologies has established itself as a leader in the home heating industry, offering a wide range of high-quality fireplaces. Among their standout products are the 5100I-GD-B and 5100I-NL-B models. These two direct vent gas fireplaces not only enhance the aesthetics of a home but also provide efficient heating solutions.

The 5100I-GD-B model boasts a contemporary design that fits well in modern interiors. Equipped with a glass front, it allows for an unobstructed view of the flames, creating a cozy atmosphere in any space. The unit's high-efficiency burner maximizes heat output while minimizing gas consumption, making it an eco-friendly choice for homeowners. Additionally, the electronic ignition system ensures reliable startups, while the integrated control panel offers easy adjustments for flame height and heat settings.

On the other hand, the 5100I-NL-B model presents a more traditional design, featuring a clean face that blends seamlessly with various décor styles. Like its counterpart, this model is also engineered for efficiency, offering an impressive Annual Fuel Utilization Efficiency (AFUE) rating. This makes it an excellent choice for those looking to reduce energy costs without sacrificing comfort. The 5100I-NL-B is also equipped with an advanced combustion system that ensures complete fuel combustion, resulting in fewer emissions and a cleaner burn.

Both models feature optional accessories, including decorative media options like logs or stones, allowing homeowners to customize the look of their fireplaces. The direct vent system allows for easy installation in various locations, as it vents gases directly outside, ensuring indoor air quality is maintained.

Safety is a priority with Hearth and Home Technologies, and both models come with a safety screen and an automatic shut-off feature. This ensures peace of mind while enjoying the warmth and ambiance these fireplaces provide.

Overall, the Hearth and Home Technologies 5100I-GD-B and 5100I-NL-B gas fireplaces exemplify the perfect blend of functionality and style, making them ideal choices for anyone looking to enhance their home's heating options. With their impressive features and efficient performance, these models are designed to keep homes warm and inviting while offering options to match personal tastes.