USA Installations only | Hearth and Home Technologies 5100I-GD-B

5100-I ACT WOOD INSERT

G. Factory-Built Zero Clearance Fireplace

(USA INSTALLATIONS ONLY)

The Quadra-Fire 5100-I Insert is listed to UL 1482 Standard and is approved for installation into listed factory-built zero clearance fireplaces listed to UL 127 conforming to the follow- ing specifications and instructions:

The original factory-built clearance fireplace chimney cap must be re-installed after installing the approved chimney liner meeting type H.T. requirements (2100°F) per UL 1777. The air flow of the factory-built zero-clearance fireplace system must not be altered. The flue liner top support attach- ment must not reduce the air flow for the existing air-cooled chimney system.

NOTE: Refer to chimney liner manufacturer for recom- mendations on supporting the liner.

Minimum Width of cavity opening:	36 in.
Minimum Height:	24 in.
Minimum Depth from front to rear:	19 in.

The fireplace must not be altered, except that the damper may be removed to accommodate a direct-connect starter pipe or chimney liner, and external trim pieces which do not affect the operation of the fireplace may be removed provid- ing they can be stored on or within the fireplace for reassem- bly if the insert is removed.

The following modifications of factory-built fireplaces are permissible:

•removal of damper

•removal of smoke shelf or baffle

•removal of ember catches

•removal of fire grate

•removal of viewing screen/curtain

•removal of doors.

The permanent metal warning label provided must be attached to the back of the fireplace, with screws or nails, stating that the fireplace may have been altered to accom- modate the insert, and must be returned to original condition for use as a conventional fireplace.

Final approval of this installation type is contingent upon the authority having jurisdiction.

The factory-built chimney must be listed per UL127 and meet the type HT requirements of UL103. Factory-built fireplace chimneys tested to UL127-1998, may be at the fireplace manufacturer’s option, tested to the same criteria as UL103 HT requirements. If the chimney is not listed as meeting HT requirements, or if the factory-built fireplace was tested prior to 1998, a full height listed chimney liner must be installed from the appliance flue collar to the chimney top. The liner must meet type HT requirements (2100ºF) per UL 1777.

The liner must be securely attached to the insert flue collar and the chimney top. To prevent room air passage to the chimney cavity of the fireplace, seal either the damper area around the chimney liner with high temperature sealant or the fireplace front with fiberglass batting. Circulating air chambers (i.e. in a steel fireplace liner or metal heat circula- tor) may not be blocked.

WARNING

Fire Risk.

When lining air-cooled factory-built chimneys:.

•Run chimney liner approved to UL 1777 Type HT requirements (2100 degrees F)

•Re-install original factory built chimney cap

ONLY

•DO NOT block cooling air openings in chimney

•Blocking cooling air will overheat the chimney

Flue Liner with Required Air Space

Stainless Steel Chimney Connector

Must Extend to Flue Liner

Minimum 8” (203mm) Masonry Thickness

in Front of Smoke Chamber

		Airtight Insulated Clean-Out
	Minimum Clearance in Accordance with
	Insert Listing	Damper Plate Removed or
		Damper Plate Removed or
		Fastened in Open Position
	Floor Protection in
	Accordance with Insert	Seal with Non-Combustible Material
	Listing	Seal with Non-Combustible Material
	Listing

Combustible Floor

Figure 18.1

Page 18

438-0380D

September 1, 2008

5100I-NL-B, 5100I-GD-B specifications

Hearth and Home Technologies has established itself as a leader in the home heating industry, offering a wide range of high-quality fireplaces. Among their standout products are the 5100I-GD-B and 5100I-NL-B models. These two direct vent gas fireplaces not only enhance the aesthetics of a home but also provide efficient heating solutions.

The 5100I-GD-B model boasts a contemporary design that fits well in modern interiors. Equipped with a glass front, it allows for an unobstructed view of the flames, creating a cozy atmosphere in any space. The unit's high-efficiency burner maximizes heat output while minimizing gas consumption, making it an eco-friendly choice for homeowners. Additionally, the electronic ignition system ensures reliable startups, while the integrated control panel offers easy adjustments for flame height and heat settings.

On the other hand, the 5100I-NL-B model presents a more traditional design, featuring a clean face that blends seamlessly with various décor styles. Like its counterpart, this model is also engineered for efficiency, offering an impressive Annual Fuel Utilization Efficiency (AFUE) rating. This makes it an excellent choice for those looking to reduce energy costs without sacrificing comfort. The 5100I-NL-B is also equipped with an advanced combustion system that ensures complete fuel combustion, resulting in fewer emissions and a cleaner burn.

Both models feature optional accessories, including decorative media options like logs or stones, allowing homeowners to customize the look of their fireplaces. The direct vent system allows for easy installation in various locations, as it vents gases directly outside, ensuring indoor air quality is maintained.

Safety is a priority with Hearth and Home Technologies, and both models come with a safety screen and an automatic shut-off feature. This ensures peace of mind while enjoying the warmth and ambiance these fireplaces provide.

Overall, the Hearth and Home Technologies 5100I-GD-B and 5100I-NL-B gas fireplaces exemplify the perfect blend of functionality and style, making them ideal choices for anyone looking to enhance their home's heating options. With their impressive features and efficient performance, these models are designed to keep homes warm and inviting while offering options to match personal tastes.