Hearth and Home Technologies 5100I-GD-B, 5100I-NL-B warranty Appliance Set-up, Leveling Bolts

Page 20

 

 

 

R

5100-I ACT WOOD INSERT

 

 

 

 

 

 

 

 

 

 

 

Appliance Set-up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Installation Outline

 

C. Panel & Trim Set Installation

 

 

 

 

Standard Size: 30-1/2” h x 47” w

 

A.7

 

 

 

1.

Record serial number on back cover of manual.

Large Size: 34-1/4” h x 51-1/4” w

 

2.

Remove the leveling bolts from the component pack and

 

Kit Includes:

Tools Needed:

 

 

 

start the bolts in the weld nuts. Figure 20.1

 

 

3.

Position insert on hearth with rear of insert extending into

(2) Side panels, left & right

Screwdrivers:

 

(1) Panel top & fastener package

Powered Phillips head

 

 

 

fireplace opening. Slide insert on its base into the open-

(2) Side trim, left & right

Long-handled Phillips head

 

 

 

ing leaving approximately 4 inches (102mm) protruding

(1) Trim top & fastener package.

 

 

out the front.

4.Assemble the panels and temporarily attach to insert.

Push insert into opening leaving 1 inch (25mm) protrud- ing out the front. Confirm the panel size is correct for the opening and that the face can be sealed off from room air when installation is complete. Figure 20.2 & 20.3.

5.Remove the panels and secure liner to the chimney ring.

6.Level the insert in its final position in the fireplace. If an offset adapter is required for installation, install it first and then secure liner to offset adapter.

7.Install the Panel & Trim set and (if applicable) the Zero

Clearance Trim Support.

1.Attaching Panels to the Insert

a.Loosely install the 2 side panels, do not tighten, using the cage nuts already attached to the appliance. (Note: The sides are not interchangeable). Figure

20.3.

b.Put top panel in place pushing straight back and then to the right to lock onto top of side panels. Attach the top panel to the sides using the panel brackets included in the fasteners package. Figure 20.2

c.Tighten side panels to the appliance using a long- handle screw driver.

B. Leveling Bolts

Two leveling bolts, 3/8” x 4” are shipped inside the com- ponent pack found inside the firebox.

NOTE: Not all installations will require the use of the level- ing bolts.

1.Remove the bolts from the component pack and insert into weld nuts welded to each side of the insert bottom

Figure 20.1

2.After securing the liner to the flue collar (or offset adapter) and the insert is in its final position, extend bolts down- ward to level insert.

Panel brackets

Do not tighten sides until top is locked into place

,EVELINGI"OLT

Figure 20.1

Figure 20.2

Back view of top and side panel assembled

Cage nut

Panel bracket

Figure 20.3

Page 20

438-0380D

September 1, 2008

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Advanced Combustion Technology ACT Hot glass will cause burnsLocation On right side of insert as face the appliance Serial NumberModel Name Manufactured DateTable of Contents Mobile Home Approved BTU & Efficiency Specifications Glass Specifications1Listing and Code Approvals Appliance CertificationGetting Started Fire SafetyDesign, Installation & Location Considerations Negative Pressure Inspect Appliance and Components Flue Draft ConsiderationsTools And Supplies Needed Panel Size 3Dimensions and ClearancesAppliance Dimensions Installation Masonry, Heat Circulating and *Zero Clearance Clearance to CombustiblesSideWall With 8 Mantel Deflector, Part NoInstallation Considerations Floor Protection USA & CanadaHearth Extension Calculating Alternate Floor Protection MaterialOutside Air Installation Disconnect the appliance from power supply Blower Cord LocationWiring Diagram Optional Offset AdapterChimney Systems Chimney RequirementsVenting Components Air Clearances Installing Chimney ComponentsOvalizing Round Stainless Steel Liners Chimney Termination Requirements Masonry Fireplace USA Installations only Factory-Built Zero Clearance Fireplace6Mobile Home Installation Requirements for outside combustion air supply toLeveling Bolts Installation Outline Panel & Trim Set InstallationAppliance Set-up Securing Liner to Flue Collar Assembling TrimZero Clearance Adjustable Trim Support Size 12 d x 50 w, 2-10 hIncluded in Kit Tools Needed 22.28Operating Instructions Over-Firing Your ApplianceWood Selection & Storage Burning ProcessAir Controls Second StageFinal Stage Start-Up SystemBuilding a Fire Heat OutputBurn Rates Opacity Smoke Blower Operating InstructionsFrequently Asked Questions Issues SolutionsGeneral Maintenance Creosote Chimney CleaningGlass Cleaning Maintaining & Servicing Your ApplianceFrequency As needed Glass Replacement Door AssemblyCleaning Plated Surfaces Slide Window In / Out Loosen Remove Bolts Firebrick Replacement Nbr Brick Size QtyBlower Replacement Baffle RemovalCorrect Baffle & Blanket Placement Incorrect PositionsTroubleshooting Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Beginning Manufactured Date November 1 Reference MaterialsExploded Views Service Parts & Accessories BRICK-438Accessories Service And Maintenance Log Date of Service Performed By Description of ServiceService And Maintenance Log Cont’d Homeowner’s Notes Warranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Contact Information Dealer Telephone

5100I-NL-B, 5100I-GD-B specifications

Hearth and Home Technologies has established itself as a leader in the home heating industry, offering a wide range of high-quality fireplaces. Among their standout products are the 5100I-GD-B and 5100I-NL-B models. These two direct vent gas fireplaces not only enhance the aesthetics of a home but also provide efficient heating solutions.

The 5100I-GD-B model boasts a contemporary design that fits well in modern interiors. Equipped with a glass front, it allows for an unobstructed view of the flames, creating a cozy atmosphere in any space. The unit's high-efficiency burner maximizes heat output while minimizing gas consumption, making it an eco-friendly choice for homeowners. Additionally, the electronic ignition system ensures reliable startups, while the integrated control panel offers easy adjustments for flame height and heat settings.

On the other hand, the 5100I-NL-B model presents a more traditional design, featuring a clean face that blends seamlessly with various décor styles. Like its counterpart, this model is also engineered for efficiency, offering an impressive Annual Fuel Utilization Efficiency (AFUE) rating. This makes it an excellent choice for those looking to reduce energy costs without sacrificing comfort. The 5100I-NL-B is also equipped with an advanced combustion system that ensures complete fuel combustion, resulting in fewer emissions and a cleaner burn.

Both models feature optional accessories, including decorative media options like logs or stones, allowing homeowners to customize the look of their fireplaces. The direct vent system allows for easy installation in various locations, as it vents gases directly outside, ensuring indoor air quality is maintained.

Safety is a priority with Hearth and Home Technologies, and both models come with a safety screen and an automatic shut-off feature. This ensures peace of mind while enjoying the warmth and ambiance these fireplaces provide.

Overall, the Hearth and Home Technologies 5100I-GD-B and 5100I-NL-B gas fireplaces exemplify the perfect blend of functionality and style, making them ideal choices for anyone looking to enhance their home's heating options. With their impressive features and efficient performance, these models are designed to keep homes warm and inviting while offering options to match personal tastes.
Top Page Image Contents