Guardian Technologies ACT2000, ACT1000 installation instructions Card Setup

Page 21

ACT1000/2000 Operating Instructions

Software Version 3.23-00

High Speed

Communications on the controller defaults to 9600 baud. The high speed option sets the controller to operate at 19200 baud. This option applies to direct connect to a PC, networked interface and printer modes of operation.

Slave Mode (ACT2000 Only)

This option selects slave mode operation as part of an ACT5000pc network. While the controller is switched into slave mode and all card events are transmitted to the network master for validation. The controller itself will not make any decisions on card events unless it is operating in fallback mode due to a network failure. This option is always set to No when using ACTWinPro.

No Hist. Log

This option suppresses the reporting of events occurring while offline in slave mode only. Normally when the controller is operating in slave mode, events are logged locally if the controller is offline, and are transmitted to the PC when communications are restored.

Print All

This option selects real-time printing to an attached serial printer. Each event is time stamped and printed immediately on the printer. Real-time printing will be temporarily suspended while a full log printout requested from the operator menu is in progress.

Remote Doors (ACT2000 Only)

This menu is where additional door stations or ACT1000 units are configured as extra doors on the ACT2000 controller. The new door (Door 3 to 16) is selected using the 0 key and the current status of the door is displayed on the bottom line of the LCD. The ✔ key may then be used to enable or disable the door:

1)To enable, select a Disabled door

2)To disable, select an Enabled door

Door 3

Disabled

Door 3

Door Normal

0for next door ✔ to enable door

0for next door ✔ to disable door

If a non-existent or incorrectly addressed door is enabled, the door will be polled for a short while, then the status will be displayed as Door Offline.

Set Password

A password consisting of a 10 digit number may be programmed into the controller to prevent unauthorized access from remote ACTWinPro users. Ensure this password matches the encryption key used by ACTWinPro.

Card Setup

The card setup menu is used to inform the controller which cards should be recognized by the system. Usually all that is required is to set the primary site code for the system. The site code is supplied along with any cards ordered, or can be obtained directly from ACT. In addition, a site code from another installation may be entered allowing shared access to the building. Where non-standard cards are being used, possibly from a previous access control or time & attendance system, the card format may be altered to accept these.

Page 18 of 32

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Page Contents Communications Default Codes Menu Navigation KeysText Entry Keys Enable Card Validity2AUX output off Option Description User SetupAssign PINs LearnBatch Cards Access Rights Group SetupOne-To-One Card Validity ACT 2000 OnlySystem Log C D E F G H + Full Access ? No Access ?Timezone At all times Door 23---7-AB Auxiliary DoorDisplay Log Wiring between Printer & Controller ControllerPrint Log Filter Log ACT 2000 OnlyUser Tracking ACT2000 Only Control DoorClear All ACT2000 Only Set Date/TimeTime Zones Set Holidays C D E Assign Name ? Clear ?March Wed 1 Mar Holiday Change PIN Issue NumberOperation PIN Only AlarmsSecond Door1 Limiting2 One-To-OneAjar Time Timers Relay TimeLock Door PIN RequiredOperation System SettingsDisplay PIN LengthFire Doors User Tracking ACT2000 OnlyOutputs ACT2000 Only Alarms Door SettingsTimed Actions Action What HappensCommunications Card Setup Factory Default Site CodeCard Format Typical ACT1000 Configuration Standalone Typical ACT2000 Configuration Standalone Always Place Varistor Across Lock Terminals DS100 Door Station InstallationController Wiring for Entry/Exit ReadersEntry Reader ACT20 PIN Pad Installation DiagramACT1000/2000 Cable Connections Interlock Configuration Fire Override ConfigurationDoor ACTWinPro Configuration ACT2000 Click here to ConnectACTWinPro ACT 4-Line Network Wiring To Mains SupplyTo PC ACT Single Line RS-485 Converter 12V DC Power Supply 300mA +12VRS-485 Bus RS-232 ACTWin SoftwareDirect Connection from Modem to Controller ACT Modem ConfigurationACTWinPro Software Actlan Configuration DiagramACTWinPro ACT System Diagram

ACT1000, ACT2000 specifications

Guardian Technologies, a leader in air purification solutions, offers two standout products in their lineup: the ACT2000 and the ACT1000. Both air purifiers leverage advanced technologies to deliver cleaner, fresher indoor air, making them ideal for families, pet owners, and anyone looking to improve their indoor air quality.

The ACT2000 is designed with a robust filtration system that includes a True HEPA filter capable of capturing 99.97% of airborne particles as small as 0.3 microns. This feature is particularly effective against allergens, dust, mold spores, and pet dander. Additionally, the ACT2000 employs an activated carbon filter that targets and neutralizes odors from cooking, pets, and smoke, ensuring that the air in your home remains fresh and pleasant.

A highlight of the ACT2000 is its innovative UV-C light technology. This feature works synergistically with the filtration system by using ultraviolet light to kill bacteria and viruses present in the air, creating a thorough air purification process. With its coverage of up to 1,250 square feet, the ACT2000 is suited for larger spaces such as living rooms, gyms, or open-concept homes. The device also comes equipped with real-time air quality monitoring, allowing users to track the air quality and adjust settings accordingly.

On the other hand, the ACT1000 is a more compact model, ideal for smaller rooms or offices up to 700 square feet. Similarly, it utilizes a True HEPA filter and an activated carbon filter to purify the air efficiently. While the ACT1000 may be smaller than its counterpart, it does not compromise on performance. The UV-C light technology is included to ensure that airborne pathogens are effectively neutralized.

Both models feature smart controls that allow users to operate the air purifiers remotely. With multiple fan speeds and a whisper-quiet operation, both units can run unobtrusively in the background, even while you’re sleeping or working. An intuitive filter replacement indicator alerts users when it’s time to change the filters, making maintenance simple and straightforward.

In summary, the Guardian Technologies ACT2000 and ACT1000 epitomize modern air purification with their combination of HEPA filtration, activated carbon, UV-C technology, and user-friendly features. Whether you choose the larger capacity of the ACT2000 or the compact efficiency of the ACT1000, both models offer an effective solution for creating a healthier indoor environment.
Top Page Image Contents