Chimney HEIGHT/DRAFT

R	5700 ACT Wood Stove

To be sure that your Quadra-Fire stove burns properly, the chimney draft (static pressure) should be approximately -.10” water column (W.C.) during a high burn and -.04” W.C. during a low burn, measured 6” (152mm) above the top of the stove after one hour of operation at each burn setting.

NOTE: These are guidelines only, and may vary somewhat for individual installations.

Your Quadra-Fire stove was designed for and tested on a 6” (152mm) chimney, 12’-14’ (360-420cm) high, (includes stove height) measured from the base of the stove. The further your stack height or diameter varies from this configuration, the possibility of performance problems exists. In addition, exterior conditions such as roof line, surrounding trees, prevailing winds and nearby hills can influence stove performance. Your local dealer is the expert in your geographic area and can usually make suggestions or discover solutions that will easily correct your flue problem, allowing your woodstove and its flue system to operate correctly and provide safe and economical heat for your home.

A masonry chimney or a Listed factory-built UL103 HT Class “A” chimney must be the required height above the roof and any other nearby obstructions. The chimney must be at least 3’ (91cm) higher than the highest point where it passes through the roof and at least 2’ (61cm) higher than the highest part of the roof or structure that is within 10’ (305cm) of the chimney, measured horizontally. See 2-10-3 Rule below.

These are safety requirements and are not meant to assure proper flue draft.

We recommend using a minimum total system height of 12' (360cm), measured from the flue collar to the top of the chimney (not including chimney cap).

Availability of combustion air: A source of air (oxygen) is necessary in order for combustion to take place. It is important to realize that whatever combustion air is consumed by the fire must be replaced. If you are using room air, the air is replaced via air leakage that occurs around windows and under doors, etc. However, in most newly constructed houses, mobile homes, or even existing homes that are fitted with tightly sealed doors and windows, the area from which the combustion air is taken is relatively air tight. In these cases, an outside air source must be made available to feed combustion air from outside the home into the stove. An Outside Air Kit is available for your stove as an option, Part 831-1780. The kit is a requirement for mobile home installations. Check with the local authorities in your area for the requirements in your location.

	2-10-3 RULE
3 ft Min	2 ft Min (61cm)
3 ft Min
(91cm)
	10 ft Min
	(305cm)
	warning!

always follow chimney connector manufacturer’s instructions for proper installation.

chimney connector is to be used only within the room, between the stove and ceiling OR wall. The connector shall not pass through an attic or roof space, closet or similar concealed space, or a floor, or ceiling. MAINTAIN minimum clearances to combustibles as REFERENCED on pageS 6, 7, 8, & 9.

September 1, 2008

250-7090E

Page

820-0721 specifications

Hearth and Home Technologies (HHT) 820-0721 is a premium fireplace and heating solution that exemplifies modern design and innovative technology. Designed for comfort and efficiency, the 820-0721 model brings together aesthetic appeal and advanced functionality, making it an ideal choice for homeowners seeking to enhance their living spaces.

One of the key features of the HHT 820-0721 is its advanced heating capabilities. Utilizing cutting-edge technology, this fireplace delivers impressive heating performance while maintaining energy efficiency. The model is engineered to provide consistent warmth, ensuring that any room remains cozy even during the coldest months of the year. With its ability to efficiently convert fuel into heat, users can enjoy optimal warmth while minimizing energy costs.

Additionally, the HHT 820-0721 incorporates a range of customization options. Homeowners can choose from a variety of styles, finishes, and sizes, allowing them to tailor the fireplace to their specific decor preferences. The sleek and modern design complements a wide array of interiors, from traditional to contemporary, making it a versatile addition to any home.

The technology behind the HHT 820-0721 is also noteworthy. Equipped with advanced safety features, this fireplace includes an automated shut-off system that ensures safe operation. The unit is designed to prevent overheating and includes protective screens that mitigate the risk of accidental burns. These safety enhancements provide peace of mind for families who prioritize both style and security.

The HHT 820-0721 is also user-friendly, featuring intuitive controls that make it easy to adjust temperature settings. Moreover, many models come with remote control options, allowing users to operate their fireplace from anywhere in the room. This convenience adds to the overall appeal of the unit, making it simple to create the perfect ambiance without the hassle of manual adjustments.

In summary, the Hearth and Home Technologies 820-0721 is a premium fireplace solution that excels in heating efficiency, design flexibility, and safety features. Its modern aesthetics, combined with advanced technology and ease of use, make it an outstanding choice for those looking to enhance their home's comfort and visual appeal. As homeowners continue to seek innovative heating solutions, the HHT 820-0721 stands out as a leader in the market.