Hearth and Home Technologies 820-0721 warranty Mobile Home Installation

Page 14

5700 ACT Wood Stove

R

MOBILE HOME INSTALLATION

You must use a Quadra-Fire Outside Air Kit for installation in a mobile home.

1.An outside air inlet must be provided for combustion and must remain clear of leaves, debris, ice and/or snow. It must be unrestricted while unit is in use to prevent room air starvation which can cause smoke spillage and an inability to maintain a fire. Smoke spillage can also set off smoke alarms.

2.Stove must be secured to the mobile home structure by bolting pedestal through hearth pad and into floor. For leg models, use 1/4” (6mm) lag bolts with the appropriate length for your application.

3.Stove must be grounded with #8 solid copper grounding wire or equivalent and terminated at each end with N.E.C. approved grounding device.

4.Stove must be installed with an approved UL103 HT ventilated chimney connector, UL103 HT chimney, and terminal cap with spark arrestor. Never use a single wall connector (stove pipe) in a mobile home installation. Use only double-wall connector pipe, Dura-Vent DVL, Selkirk metalbestos DS or Security DL double-wall connector or any Listed double-wall connector pipe.

5.Refer to page 6 of this manual or the Serial Number label on the back of the stove for clearances to combustibles.

6.Floor protection requirements on pages 7-8must be followed precisely.

7.In Canada, this appliance must be connected to a 6” (152mm) factory-built chimney conforming to CAN/ULC-

629M, STANDARD FOR FACTORY BUILT CHIMNEYS.

8.Use silicone to create an effective vapor barrier at the location where the chimney or other component penetrates to the exterior of the structure.

9.Follow the chimney and chimney connector manufacturer’s instructions when installing the flue system for use in a mobile home.

NOTE: Offsets from the vertical, not exceeding 45°, are allowed per Section 905(a) of the Uniform Mechanical Code (UMC). Offsets greater than 45° are considered horizontal and are also allowed, providing the horizontal run does not exceed 75% of the vertical height of the vent. Construction, clearance and termination must be in compliance with the UMC Table 9C.

 

Spark Arestor Cap

Storm Collar

 

 

roof Flashing

Joist Shield/Firestop

Double Wall

 

 

Connector Pipe

 

Outside Air

 

Kit Connector

Floor

 

Protector

 

 

Outside Air

 

Floor Vent

FIGURE 14A

WARNING: NEVER DRAW COMBUSTION AIR FROM A WALL, FLOOR OR CEILING CAVITY OR FROM ANY ENCLOSED SPACE SUCH AS AN ATTIC OR GARAGE.

CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED. (i.e., DO NOT CUT THROUGH FLOOR JOIST, WALL STUD, CEILING TRUSS, ETC.)

NOTE: Top sections of chimney must be removable to allow maximum clearance of 13.5 ft (411cm) from ground level for transportation purposes.

WARNING: DO NOT INSTALL IN SLEEPING ROOM.

10.Burn wood only. Other types of fuels may generate poisonous gases (e.g., carbon monoxide).

11.If unit burns poorly while an exhaust blower is on in home, (i.e., range hood), then increase combustion air.

Page 14

250-7090E

September 1, 2008

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Wood Stove Sample of Serial Number / Safety Label Location On right side of insert as face the applianceTable of Contents Listings & Safety Cautions Installation Materials Needed for SafetyDimensions Locating Your StoveSerial Number / Safety Label Location On Back of Stove Clearances to Combustibles UL and ULCFloor Protection USAFloor Protection Cont’d Alternate Materials WorksheetChimney HEIGHT/DRAFT Masonry Chimney Flue SystemsMasonry Chimney Cont’d Solid Pack Chimney with Metal Supports AS a Thimble Solid Pack Chimney with Metal Supports AS a Thimble Cont’d Connection to a Metal PRE-FABRICATED Chimney Interior ChimneyMobile Home Installation LEG Model ASH Removal System ARS InstallationARS Operating and Cleaning Pedestal ModelPedestal or LEG KIT Installation Pedestal Model LEG ModelInstallation of Optional BLOWER, Part Adjusting the Blower Speed CONTROL, if NecessaryOutside AIR KIT Installation Pedestal ModelAIR Controls Operating Instructions Cont’d Building a FireWood Selection and Storage OpacityBurn Rates Blower Operating InstructionsCreosote Maintenance and Glass CareChimney Cleaning Glass CareGlass Replacement Replace with 5mm ceramic glass onlySpring Handle Warning Door Handle AssemblyBaffle Removal and Installation Appliance AccessoriesService Parts DOOR, Glass and Door Handle Assembly Exploded ViewsService And Maintenance Log Service And Maintenance Log Cont’d Homeowner’s Notes Warranty Policy CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d ACT Wood Stove

820-0721 specifications

Hearth and Home Technologies (HHT) 820-0721 is a premium fireplace and heating solution that exemplifies modern design and innovative technology. Designed for comfort and efficiency, the 820-0721 model brings together aesthetic appeal and advanced functionality, making it an ideal choice for homeowners seeking to enhance their living spaces.

One of the key features of the HHT 820-0721 is its advanced heating capabilities. Utilizing cutting-edge technology, this fireplace delivers impressive heating performance while maintaining energy efficiency. The model is engineered to provide consistent warmth, ensuring that any room remains cozy even during the coldest months of the year. With its ability to efficiently convert fuel into heat, users can enjoy optimal warmth while minimizing energy costs.

Additionally, the HHT 820-0721 incorporates a range of customization options. Homeowners can choose from a variety of styles, finishes, and sizes, allowing them to tailor the fireplace to their specific decor preferences. The sleek and modern design complements a wide array of interiors, from traditional to contemporary, making it a versatile addition to any home.

The technology behind the HHT 820-0721 is also noteworthy. Equipped with advanced safety features, this fireplace includes an automated shut-off system that ensures safe operation. The unit is designed to prevent overheating and includes protective screens that mitigate the risk of accidental burns. These safety enhancements provide peace of mind for families who prioritize both style and security.

The HHT 820-0721 is also user-friendly, featuring intuitive controls that make it easy to adjust temperature settings. Moreover, many models come with remote control options, allowing users to operate their fireplace from anywhere in the room. This convenience adds to the overall appeal of the unit, making it simple to create the perfect ambiance without the hassle of manual adjustments.

In summary, the Hearth and Home Technologies 820-0721 is a premium fireplace solution that excels in heating efficiency, design flexibility, and safety features. Its modern aesthetics, combined with advanced technology and ease of use, make it an outstanding choice for those looking to enhance their home's comfort and visual appeal. As homeowners continue to seek innovative heating solutions, the HHT 820-0721 stands out as a leader in the market.
Top Page Image Contents