State Industries 650A, 540A, 740A warranty Direct Vent System Installation

Page 10

1.Shall be located not less than 12” (304.8 mm) above grade.

2.Shall be located not less than 3 (.9144 m) feet horizontally from and not less than 3 feet (.9144 m) below an exhaust vent terminal.

3.Shall not be located directly above an exhaust terminal.

4.Shall be located 12” (304.8 mm) above the snow line in geographical areas where snow accumulates.

5.Shall be located not less than 7 feet 2.1 m) above grade when adjacent to a public walkway.

6.Shall not be closer than 3 feet (.9144 m) from the inside corner of an L - shaped structure.

7.Shall be located not less than 3 feet (.9144 m) horizontally or 3 feet (.9144 m) vertically from gas line, meter, or other gas supply entering a structure, see Figure 6.

DIRECT VENT SYSTEM INSTALLATION

Plan the vent system backwards from the vent hood to the heater.

1.Use the inside wall cover plate as a template to mark two holes in the appropriate places on the wall. Cut holes 1/2” (12.7 mm) larger to facilitate easy installation of vent hoods, see Figures 6 and 7.

BEWARE OF CONCEALED WIRING AND PIPING INSIDE WALL. REFER TO TABLE 3 FOR THE MAXIMUM WALL THICKNESS “B” FOR EACH MODEL.

2.Slide hoods through openings from outside. Fasten hoods to exterior wall with anchors and screws supplied.

3.Install cover plate and fasten to inside wall with 4 screws

4.Attach a seal ring (Selkirk Metalbestos Model SR or equivalent) to the vent hood collar, see Figure 7.

FIGURE 7B.

FIGURE 7.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Models GPG/GPV-540A, 650A and 740A ROUGH-IN Dimensions ForewordTable of Contents General Safety InformationFeatures Extended NON-USE PeriodsRequired Ability Installation InstructionsDishwashing Machine Requirement UncratingAIR Requirements Hard WaterClearances VentingHorizontal SIDE-WALL Venting For GPV Models Barometric Draft Control AssemblyVertical Venting for GPG Models Vent ConnectionsVent System Installation Vent Terminal LOCATIONS-EXHAUSTDirect Venting for GPV Models Vent Terminal LOCATIONS-INTAKEDirect Vent System Installation GAS Piping Vent Diameter GPV -540A, 650A & 740AGAS Valves GAS Meter Size City Gases onlyGAS Pressure Regulation Sources of Ignition for this PurposeRelief Valve Water Line ConnectionsSystem Connections Installation Diagrams Circulating Pump Wiring DiagramWiring Diagram for Tempered Water Loop if Used Circulating Pump Wiring Diagram Page Manifold Kits Purging Heater WiringStart UP FillingPage Page For Your Safety Read Before Lighting Sequence of Operation Page Premix LOW NOx Burner Exploded View for GPG Models Premix LOW NOx Burner Exploded View for GPV Models Maintenance General InformationSediment Removal DrainingLime Scale Removal Checklist and Service Water Heater Makes Sounds TroubleshootingWater is TOO HOT Water Leakage is SuspectedMotor will not RUN Burner Lockout Once in a WhileNoisy Burner Operation GAS Fails to Shut OFFModel GPG/GPV Limited Warranty Replacement Parts List Part List for GPG Burner Assembly Lindahl Parkway, Ashland City, TN Phone 800-821-2017 Fax

740A, 540A, 650A specifications

State Industries is well-known for its high-quality water heating solutions, and among its product lineup, the 650A, 540A, and 740A models stand out for their advanced features and technology. Each of these models cater to different needs, making them versatile choices for both residential and commercial applications.

The State Industries 650A model is designed for efficient hot water delivery, featuring a powerful heating element that ensures rapid heating of water. It has an impressive recovery rate, which is crucial for homes with higher hot water demands. The 650A also integrates a robust insulation system that minimizes heat loss, ensuring energy efficiency. With a capacity of 65 gallons, it is perfectly suited for larger households or small commercial setups.

Next in the lineup is the 540A model, which strikes a balance between performance and size. With a capacity of 54 gallons, this model is ideal for medium-sized homes. It employs advanced heating technology that significantly reduces energy consumption while providing consistent hot water supply. The 540A is also equipped with a user-friendly digital interface that allows homeowners to monitor temperatures and set preferences with ease. Additionally, it features durable construction materials, promoting longevity and reliability in everyday use.

Finally, the 740A model offers the highest capacity of the three, boasting an extensive 74-gallon storage tank. This model is particularly advantageous for larger families or businesses that require substantial hot water availability. Similar to the 650A, the 740A employs advanced insulation techniques, ensuring that energy loss is minimized. It's also equipped with smart technology that allows for remote monitoring and adjustment, providing convenience for busy homeowners.

All three models utilize high-efficiency heating elements and are designed for easy installation and maintenance. They incorporate safety features such as temperature and pressure relief valves to ensure safe operation. Moreover, these units are built to meet or exceed industry standards, making them a reliable choice for anyone looking to invest in a hot water solution. Overall, State Industries continues to lead the market with innovative products like the 650A, 540A, and 740A, catering to diverse hot water needs with efficiency and reliability.
Top Page Image Contents