Omron DDAA1000/SRM manual Main Menu Option 0 Set Operation Mode, Point-to-point Master

Page 25

DDAA1000/SRM User Guide

Main Menu Option (0): Set Operation Mode

When item (0) is selected, the Operation Mode Menu appears as shown in figure 12. The Operation Mode option is used to designate the method in which the particular DDAA1000/SRM will be used. The DDAA1000/SRM operates in a master to remote configuration; therefore, any radio modems that are intended to operate together must be set up as such. In a point- to-point setup, either the master or remote may be used on either end of the communications link. One consideration when setting up the radio modems is that a number of parameters are controlled by the settings in the master; therefore, you may wish to deploy the master on the communications end where you will have easier access to the radio modem.

Figure 12: Mode Menu

Shown below are example settings. Please refer to supplied configuration sheets for your modem’s configuration.

(0)Point-to-point Master

The DDAA1000/SRM operates in a master/remote configuration. When designated as a master in point-to-point mode, the radio modem will call any or all remotes it is instructed to call in the call book. The master determines

the settings used for all Radio Transmission Characteristics, regardless of the settings in the remotes and/or repeaters.

(1)Point-to-Point Remote

When set up as a point-to-point remote, a DDAA1000/SRM will communicate with any master in its call book, either directly or through one or two repeaters. When functioning as a remote, the Entry to Call feature in the

radio modem’s call book (Figure 13) is not operational. The remote will communicate with any master on the list that calls.

(2)Point-to-Multi-Point Master

The DDAA1000/SRM may be set to run in multi-point mode, which allows one master to simultaneously be in communication with numerous remotes. A point-to-multi-point master will communicate only with other radio modems designated as point-to-multi-point remotes or point-to-multi-point repeaters.

(3)Point-to-Multi-Point Remote

Setting (3) allows the radio modem to operate as a remote in a multi-point network.

Please refer to the section entitled multi-point Operation, for more information on running a multi-point network.

PN 161-09981-002C

rev 8/04

DATA-LINC GROUP

23

Page 24 Page 26
Image 25
Page 24 Page 26
Contents DDAA1000/SRM Product User Guide FCC NotificationTable of Contents DATA-LINC Group DDAA1000 and DD1000 IntroductionAntenna Connectoin Type Power ConnectorTeminal Block Connections Discrete OperationMaster Remote Point-to-Point Discrete OperationMaster Point-to-Multipoint Discrete OperationAnalog Operation Supply loop powerPoint-to-Point Analog System Needed. The DDAA1000 unites do notMaster or Remote Connection of a flow meter to the DDAA1000/SRM unitPoint-to-Multipoint Analog System Factory Configuration ProcessPoint-to-Multipoint Analog Example Remote Point-to-Multipoint Analog OperationLayout Drawing Changing System or Radio ConfigurationsTechnical Specifications Troubleshooting Return Material Authorization Product WarrantyTechnical Support Contact InformationTOP Appendix aAppendix B DDAA1000 DD1000 ConfigurationDATA-LINC Group Ddaa Eeprom MENU** *SET Caplck DATA-LINC Group Terminal Settings Appendix C Radio ConfigurationMain Menu Point-to-point Master Main Menu Option 0 Set Operation ModePoint-to-Point Remote Point-to-Multi-Point MasterDDAA1000/SRM User Guide Point-to-Point Remote/Repeater Point-to-Point Remote/Master SwitchablePoint-to-Point Repeater Point-to-Multi-Point RepeaterAvailable data word length and parity selections Main Menu Option 1 Set Baud RateModBus RTU Call Book Menu Main Menu Option 2 Edit Call BookEntry Number Repeater 000-0000 Edit Call Book in Multi-Point SystemsFreqKey Main Menu Option 3 Edit Radio Transmission CharacteristicsMax Packet Size and 2 Min Packet Size Selections Maximum Packet Size Settings where RF Data Rate=3 DDAA1000/SRM User Guide Minimum Packet Size Settings bytesRF Data Rate Xmit RatePower Transmit Settings DDAA1000/SRM User Guide RF Xmit PowerRemote Security RTS to CTSHigh Noise DDAA1000/SRM User Guide Lowpower ModeMCU speed Main Menu Option 4 Show Radio Statistics Average Signal LevelAverage Noise Level Overall Rcv Rate %DDAA1000/SRM User Guide Number of Disconnects Radio TemperatureMulti-Point Operation Multi-Point Parameters Main Menu Option 5 Edit Multi-Point ParametersRemote/Repeater DiagnosticsSubNet ID Radio IDMain Menu Option 8 Password Disabling Password Changing a PasswordDDAA1000/SRM and DD1000/SRM Placement Locations
Top Page Image Contents