Omron DDAA1000/SRM manual Changing a Password, Disabling Password

Page 40

DDAA1000/SRM User Guide

To back out of the process and not enable the password, hit escape. To set a password, type in exactly 4 characters. At any point in the process you can cancel by hitting the escape key. Once the 4 characters have been entered, you will be prompted with “<enter> to accept, <esc> to quit”.

At this point, if you wish to accept the password entered and enable the feature, press the enter key. The password that you have chosen is displayed on the line above (please note that the password is case sensitive). To quit the process and not enable the password, press escape.

Changing a Password

Once the password feature has been enabled, it is possible to change to a new password. To enter a new password select

(8)from the Main Menu. You will be prompted with “Enter Security Code”. Enter the current password. Once the password has been entered correctly (it is case sensitive) you will be prompted to enter the new password. At any point this process may be cancelled by pressing escape.

Disabling Password

The process to disable the password is similar to the process to change the password. However, when prompted to enter the new password, the following procedure needs to be followed:

1.Hold the “Alt” key down and using the number key pad (not the numbers across the top of the keyboard) type “0255”

2.Release the “Alt” key

3.Repeat steps 1 and 2 three more times (this will enter 0255 a total of four times).

4.You will be prompted with “<Enter> to accept, <esc> to quit.

5.Hit the “Enter” key to disable the password or hit the escape key to keep the password

38	DATA-LINC GROUP

PN 161-09981-002C

rev 8/04

Image 40

Contents DDAA1000/SRM FCC Notification Product User GuideTable of Contents DATA-LINC Group Introduction DDAA1000 and DD1000Antenna Connectoin Type Power ConnectorTeminal Block Discrete Operation ConnectionsPoint-to-Point Discrete Operation Master RemotePoint-to-Multipoint Discrete Operation MasterSupply loop power Analog OperationPoint-to-Point Analog System Needed. The DDAA1000 unites do notConnection of a flow meter to the DDAA1000/SRM unit Master or RemoteFactory Configuration Process Point-to-Multipoint Analog SystemPoint-to-Multipoint Analog Operation Point-to-Multipoint Analog Example RemoteChanging System or Radio Configurations Layout DrawingTechnical Specifications Troubleshooting Product Warranty Return Material AuthorizationTechnical Support Contact InformationAppendix a TOPDDAA1000 DD1000 Configuration Appendix BDATA-LINC Group Ddaa Eeprom MENU** *SET Caplck DATA-LINC Group Appendix C Radio Configuration Terminal SettingsMain Menu Main Menu Option 0 Set Operation Mode Point-to-point MasterPoint-to-Point Remote Point-to-Multi-Point MasterPoint-to-Point Remote/Master Switchable DDAA1000/SRM User Guide Point-to-Point Remote/RepeaterPoint-to-Point Repeater Point-to-Multi-Point RepeaterAvailable data word length and parity selections Main Menu Option 1 Set Baud RateModBus RTU Main Menu Option 2 Edit Call Book Call Book MenuEdit Call Book in Multi-Point Systems Entry Number Repeater 000-0000FreqKey Main Menu Option 3 Edit Radio Transmission CharacteristicsMax Packet Size and 2 Min Packet Size Selections DDAA1000/SRM User Guide Minimum Packet Size Settings bytes Maximum Packet Size Settings where RF Data Rate=3Xmit Rate RF Data RateDDAA1000/SRM User Guide RF Xmit Power Power Transmit SettingsRemote Security RTS to CTSHigh Noise DDAA1000/SRM User Guide Lowpower ModeMCU speed Average Signal Level Main Menu Option 4 Show Radio StatisticsAverage Noise Level Overall Rcv Rate %DDAA1000/SRM User Guide Number of Disconnects Radio TemperatureMulti-Point Operation Main Menu Option 5 Edit Multi-Point Parameters Multi-Point ParametersDiagnostics Remote/RepeaterSubNet ID Radio IDMain Menu Option 8 Password Changing a Password Disabling PasswordDDAA1000/SRM and DD1000/SRM Placement Locations