Enviro 50-1096, C-10637 owner manual Direct Vent Model, Preparing Your Sienna for Installation

Page 13

Initial Installation

QUALIFIED INSTALLERS ONLY

DIRECT VENT MODEL:

WARNING: This appliance has been designed to draw room air for proper heat circulation from the sides of the unit. Blocking or modifying the louvers in any way can create hazardous situations.

This model is vented with two (2) 3” aluminum or stainless steel flex vent leading into a co-linear to co-axial vent adaptor and using a vertical termination cap. The flue collars of this model will fit inside of standard 3” vent and may be fastened directly to the vent. The Exhaust vent is on the right of the flue connector. The Air Intake is on the left side of the vent collar plate (this outlet is not in the center, it is off to one side of the vent collar plate.)

Check periodically that the vents are unrestricted. Also ensure that all direct vent pipes have been properly sealed and installed after routine inspection or cleaning. The air intake and exhaust pipes must be installed in the correct locations on the removable connector.

PREPARING YOUR SIENNA FOR INSTALLATION:

Remove the packaging from the appliance and surround panels; check to make sure there is no damage. Carefully check the glass door. Do not use the unit if it is damaged. In the event damage is found, please report it to both the courier and your dealer as soon as possible.

Carefully clean the fireplace and flue before installing the stove. Failure to do so may result in fumes or dirt being blown into the room and may cause a fire leading to death or serious injury.

1.Remove the unit from the box and remove all packaging material from the appliance.

2.Remove door. See “DOOR REMOVAL”.

3.Remove log and ember set and all wrapping material from the stove. Remove wrapping material from log and embers and check for any damage. If damage is observed, do not use unit and contact your local dealer.

4.Remove the vent collar plate from the top of the stove by unscrewing the two (2) T-20 Torx screws located on the center top of the stove. Slide the collar plate backwards. If the fireplace that the unit is to be installed into is high, the collar plate does not need to be removed. Properly secure the vent collar plate to the flexible vent pipe liner(s) previously installed in the chimney. Be careful not to over- stretch the liner(s).

5.Place the unit part way into the fireplace. Connect the fireplace insert’s flexible gas line to the household gas supply, using locally approved methods. Place the electric cable so it can be connected to the power supply.

6.As you push the unit into its final position in the fireplace, if the vent collar plate was removed, reinstall it to the stove by sliding it along the draft hood and secure with the screw.

7.Adjust the leveling legs to ensure the unit is level. There are two (2) leveling legs on each side (shown in Figure 11).

Leveling Legs

two (2) on each side

Figure 11: Leveling legs position.

13

Image 13
Contents What to do if YOU Smell GAS For Your Safety Safety PrecautionsGeneral Table of Contents Vented GAS Fireplace Heater Sienna BV/DV NG/LPG Codes And ApprovalsDimensions SpecificationsRating Label Location 33 x 46 84cm x 193 cm Pilot Lighting Instructions Operating InstructionsPilot Light Burner Lighting Remote Controls OptionalTurn OFF Unit Blower SpeedCleaning the Glass Maintenance And ServiceCleaning the Firebox Cleaning the Plated SurfacesFuel Conversion To be Installed by a Qualified Service Agency onlyClearances to Combustibles Initial InstallationMinimum Fireplace Size Vent Model Automatic Flue GAS Spill Switch B-VENT Model onlyDirect Vent Model Preparing Your Sienna for InstallationVenting Fireplace Inserts Installation of Sienna DV and BVElectrical Requirements Prong from this plugGAS Line Connection Gas Line ConnectionConverting to a BV fireplace Converting a Direct Vent Fireplace to a B-VENT FireplaceReplacing the Blower Secondary InstallationDoor Removal Installation of Surround PanelEmpty firebox with grate and locator pins LOG SET and Ember InstallationThird Stage Log Set Installation Never operate the fireplace with the glass door removed Adjusting Venturi AIR SettingsRemoving the Brick Panel Brick panel set is fragile, handle with extreme careBV only Trouble ShootingNumber Parts List- Unit ComponentsComponentsDiagramParts Parts Diagram Burner Parts List Options Parts Diagram Options To the Dealer WarrantyInstallation Data Sheet