This product can accept any of the following chargers listed below. Model UA180020B or Model UA160015a
Assembly | A |
|
|
Mounting accessories (figures A & B) |
| 2 | |
|
| ||
The |
| 10 |
|
brush that can be folded forward for dusting |
|
| |
and upholstery cleaning. |
|
|
|
The pet hair cleaning tool (13) is for use |
|
|
|
when vacuuming pet hair and/or |
|
|
|
debris from carpeted or upholstery surfaces. |
|
|
|
WARNING: Injury to | 11 |
|
|
pets. Do not use pet hair cleaning tool |
|
|
|
directly on animals. |
|
|
|
The crevice tool (11) allows for vacuuming in |
|
|
|
narrow and hard |
|
|
|
• To attach an accessory (11), press the |
|
|
|
accessory clip (10) and slide the accessory |
|
|
|
onto the handle (2). |
|
|
|
• Toremove an accessory, press the accessory |
|
| 16 |
clip (10) and remove the accessory. | B | 2 | |
To unwrap and extend the handle and |
|
| |
hose: |
|
|
|
The handle and hose can be unwrapped |
|
|
|
from the main appliance for extended reach |
|
|
|
when cleaning. Grab the handle where the |
|
|
|
arrows indicate and lift upwards. Unwrap |
|
|
|
the handle and hose from the main |
|
|
|
appliance. The hose can extend up to |
| 11 | 16 |
approximately 4 feet (1.21m). |
| ||
To place the handle and hose back onto the |
|
|
|
main appliance, wrap the hose back |
|
|
|
underneath and around the vac making sure |
|
|
|
that the hose fits between the two “feet” of |
|
|
|
the appliance. Align the handle with its |
|
|
|
cradle and click back into place. |
|
|
|
The handle (2) can be removed from the |
|
|
|
hose allowing the accessories to be |
|
|
|
connected directly to the hose cuff (16) |
|
|
|
when desired. |
|
|
|
To remove the handle: |
|
|
|
• Unclip the handle (2) from the appliance. | C |
|
|
• Rotate the locking ring (3) counterclockwiseto |
|
|
|
release the clips. |
|
|
|
• Pull the hose away from the handle (2). |
|
|
|
• Fit the accessorydirectly tothe hose cuff(16). |
|
|
|
To refit the handle: |
|
|
|
• Remove the accessory from the hose. |
|
|
|
• Push the hose into the handle (2). Rotate |
|
|
|
locking ring (3) clockwise until it clicks into |
|
| 12 |
place. |
|
| |
Fitting the accessory caddy (figure C) |
|
|
|
When not in use, accessories can be stored |
|
|
|
in the accessory caddy (12). The accessory |
|
|
|
caddy can be removed if necessary. |
|
|
|
• To install the accessory caddy (12) push it |
|
|
|
onto the lugs on the body of the appliance |
|
|
|
until it clicks into place. NOTE: Caddy only |
|
|
|
fits on one side of the appliance. |
|
|
|
• To remove the accessory caddy (12) grasp |
|
|
|
either of the rounded sides and pull it away from the base of the appliance. |
4