Desa GMP26T, GMP20BT, GMP16T, GMP30BT Mounting Heater to Floor with Optional Floor KIT

Page 11

INSTALLATION

Continued

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 12).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hol- low or solid wall, install wall anchors. Fol- low steps 1 through 4 under Attaching To Wall Anchor Method, page 10.

If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly se- cured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas con- nections and checking for leaks (see pages 12 through 14).

Front View

Heater

Wall

 

 

Spacer

Side View

Figure 12 - Installing Bottom Mounting

Screws

MOUNTING HEATER TO FLOOR WITH OPTIONAL FLOOR KIT

Mounting Base Feet to Heater

1.Lay heater cabinet on its back on a table with the heater bottom overhanging the table edge.

2.Align holes in base foot with mounting holes on bottom of cabinet (see Figure 13).

3.Secure base foot to heater using sheet metal screws.

4.Repeat for other side.

Wood

Screw

Base Foot

Sheet Metal Screw

Figure 13 - Installing Base Feet

Mounting Base Feet to Floor (Where required by local code)

1.Remove front panel (see Removing Front Panel of Heater, page 9).

2.Position heater with base feet in desired loca- tion. Mark holes for drilling. Remove heater with base.

3.For carpeted floors, make a small cut with a sharp knife at marked locations prior to drill- ing. If mounting base to a wood floor, drill 1/8 inch diameter hole, 3/4 inch deep. (Do not use anchors in wood floors).

If mounting base to a concrete floor, drill with 1/4 inch diameter concrete drill bit, 13/8 inches into floor. Insert anchors completely into holes.

4.Reposition heater with base feet over holes. Secure base to floor with wood screws. See Figure 13.

113048-01C

www.desatech.com

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents What to do if YOU Smell GAS Table of Contents Safety Information Local Codes Safety Information Product IdentificationConfined and Unconfined Space AIR for Combustion VentilationProviding Adequate Ventilation Unusually Tight ConstructionDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationVentilation Air From Inside Building InstallationVentilation AIR Check GAS TypeLocating Heater Installation ItemsInstalling Heater to Wall Placing Heater On Mounting Bracket 20,000 Btu/Hr ModelsAttaching To Wall Anchor Method Mounting Base Feet to Heater Installing Bottom Mounting ScrewsMounting Base Feet to Floor Where required by local code Mounting Heater to Floor with Optional Floor KITTypical Inlet Pipe Diameters Connecting to GAS SupplyTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Pressure Testing GAS Supply Piping SystemChecking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPaManual Control Models Lighting Instructions For Your Safety Read Before LightingPressure Testing Heater GAS Connections Operating HeaterTo Turn OFF GAS To Appliance Manual Lighting ProcedureTo Select Heating Level for Infrared Heaters Thermostat Controlled Models Lighting Instructions Control Knob GMP16T Inspecting HeaterThermostat Control Operation Pilot Flame PatternBurner Flame Pattern for Infrared Heaters Inpecting HeaterBurner Flame Pattern for Blue Flame Heaters Cabinet Cleaning MaintenanceODS/PILOT and Burner Burner Pilot AIR InletObserved Problem Possible Cause Remedy TroubleshootingPressed See Cleaning and Mainte Statement above Gas leak. See WarningGMP16 GMP26 GMP16T GMP26T SpecificationsGMP30BT GMP20BT Accessories Service HintsTechnical Service Service Publications Replacement PartsModels GMP16, GMP26, GMP16T, and GMP26T Illustrated Parts BreakdownParts AVAILABLE-NOT Shown Parts ListModels GMP16 and GMP26 Illustrated Parts Breakdown and Parts ListModels GMP16T and GMP26T ODS/Pilot Burner Assembly GMP16TModels GMP20BT and GMP30BT Parts Available not Shown Limited Warranty VENT-FREE Residential GAS Heaters Warranty InformationKeep this Warranty
Top Page Image Contents